Initial commit
Signed-off-by: Thomas Schmid <tom@lfence.de>
This commit is contained in:
commit
f784e3b47f
846
printer.cfg
Normal file
846
printer.cfg
Normal file
@ -0,0 +1,846 @@
|
||||
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
||||
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
||||
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
||||
|
||||
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
||||
|
||||
## *** THINGS TO CHANGE/CHECK: ***
|
||||
## MCU paths [mcu] section
|
||||
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
## Z Endstop Switch location [safe_z_home] section
|
||||
## Homing end position [gcode_macro G32] section
|
||||
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||
## Probe points [quad_gantry_level] section
|
||||
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||
## PID tune [extruder] and [heater_bed] sections
|
||||
## Thermistor types [extruder] and [heater_bed] sections
|
||||
## Probe pin [probe] section
|
||||
## Fine tune E steps [extruder] section
|
||||
|
||||
[mcu rpi]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[adxl345]
|
||||
cs_pin: rpi:None
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
175, 175, 50
|
||||
|
||||
[mcu]
|
||||
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
||||
##--------------------------------------------------------------------
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_4A0028000250534E4E313120-if00
|
||||
restart_method: command
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 350
|
||||
max_accel: 3000 #Max 4000
|
||||
max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## B Stepper - Left
|
||||
## Connected to MOTOR_0
|
||||
## Endstop connected to DIAG_0
|
||||
[input_shaper]
|
||||
shaper_freq_x: 59.6
|
||||
shaper_type_x: mzv
|
||||
shaper_freq_y: 45
|
||||
shaper_type_y: mzv
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PF13
|
||||
dir_pin: PF12
|
||||
enable_pin: !PF14
|
||||
rotation_distance: 40
|
||||
microsteps: 32
|
||||
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: PG6
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
#position_endstop: 300
|
||||
#position_max: 300
|
||||
|
||||
## Uncomment for 350mm build
|
||||
position_endstop: 350
|
||||
position_max: 350
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC4
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## A Stepper - Right
|
||||
## Connected to MOTOR_1
|
||||
## Endstop connected to DIAG_1
|
||||
[stepper_y]
|
||||
step_pin: PG0
|
||||
dir_pin: PG1
|
||||
enable_pin: !PF15
|
||||
rotation_distance: 40
|
||||
microsteps: 32
|
||||
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: PG9
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
#position_endstop: 300
|
||||
#position_max: 300
|
||||
|
||||
## Uncomment for 350mm build
|
||||
position_endstop: 358
|
||||
position_max: 358
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PD11
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left
|
||||
## Connected to MOTOR_2
|
||||
## Endstop connected to DIAG_2
|
||||
[stepper_z]
|
||||
step_pin: PF11
|
||||
dir_pin: PG3
|
||||
enable_pin: !PG5
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 32
|
||||
endstop_pin: PG10
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
#position_endstop: -0.5
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_max: 230
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
#position_max: 280
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
position_max: 330
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
position_min: -5
|
||||
homing_speed: 8
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC6
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left
|
||||
## Connected to MOTOR_3
|
||||
[stepper_z1]
|
||||
step_pin: PG4
|
||||
dir_pin: !PC1
|
||||
enable_pin: !PA0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 32
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z1]
|
||||
uart_pin: PC7
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right
|
||||
## Connected to MOTOR_4
|
||||
[stepper_z2]
|
||||
step_pin: PF9
|
||||
dir_pin: PF10
|
||||
enable_pin: !PG2
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 32
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z2]
|
||||
uart_pin: PF2
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right
|
||||
## Connected to MOTOR_5
|
||||
[stepper_z3]
|
||||
step_pin: PC13
|
||||
dir_pin: !PF0
|
||||
enable_pin: !PF1
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 32
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z3]
|
||||
uart_pin: PE4
|
||||
interpolate: false
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
## Connected to MOTOR_6
|
||||
## Heater - HE0
|
||||
## Thermistor - T0
|
||||
[extruder]
|
||||
step_pin: PE2
|
||||
dir_pin: PE3
|
||||
enable_pin: !PD4
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
## 22.6789511 is a good starting point
|
||||
rotation_distance: 22.536398 #Bondtech 5mm Drive Gears
|
||||
## Update Gear Ratio depending on your Extruder Type
|
||||
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||
## Use 80:20 for M4, M3.1
|
||||
gear_ratio: 50:17 #BMG Gear Ratio
|
||||
microsteps: 32
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
heater_pin: PA2
|
||||
## Validate the following thermistor type to make sure it is correct
|
||||
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: PF8
|
||||
# The chip select line for the sensor chip. This parameter must be
|
||||
# provided.
|
||||
spi_speed: 2000000
|
||||
# The SPI speed (in hz) to use when communicating with the chip.
|
||||
# The default is 4000000.
|
||||
spi_software_sclk_pin: EXP2_2
|
||||
spi_software_mosi_pin: EXP2_6
|
||||
spi_software_miso_pin: EXP2_1
|
||||
# See the "common SPI settings" section for a description of the
|
||||
# above parameters.
|
||||
#tc_type: K
|
||||
#tc_use_50Hz_filter: False
|
||||
#tc_averaging_count: 1
|
||||
# The above parameters control the sensor parameters of MAX31856
|
||||
# chips. The defaults for each parameter are next to the parameter
|
||||
# name in the above list.
|
||||
rtd_nominal_r: 100
|
||||
rtd_reference_r: 430
|
||||
rtd_num_of_wires: 4
|
||||
#rtd_use_50Hz_filter: False
|
||||
# The above parameters control the sensor parameters of MAX31865
|
||||
# chips. The defaults for each parameter are next to the parameter
|
||||
# name in the above list.
|
||||
min_temp: 0
|
||||
max_temp: 480
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
#control = pid
|
||||
#pid_kp = 26.213
|
||||
#pid_ki = 1.304
|
||||
#pid_kd = 131.721
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.038
|
||||
## Default is 0.040, leave stock
|
||||
pressure_advance_smooth_time: 0.040
|
||||
|
||||
## E0 on MOTOR6
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PE1
|
||||
interpolate: false
|
||||
run_current: 0.5
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
## SSR Pin - HE1
|
||||
## Thermistor - TB
|
||||
heater_pin: PA3
|
||||
## Validate the following thermistor type to make sure it is correct
|
||||
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
||||
sensor_type: Generic 3950
|
||||
sensor_pin: PF3
|
||||
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
||||
max_power: 0.6
|
||||
# tba: test --> 0
|
||||
min_temp: 0
|
||||
max_temp: 120
|
||||
#control: pid
|
||||
#pid_kp: 58.437
|
||||
#pid_ki: 2.347
|
||||
#pid_kd: 363.769
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
|
||||
## Select the probe port by type:
|
||||
## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V.
|
||||
#pin: ~!PB7
|
||||
## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO.
|
||||
#pin: PG15
|
||||
## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper
|
||||
pin: ~PC5
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
x_offset: 0
|
||||
y_offset: 25.0
|
||||
z_offset: 0
|
||||
speed: 10.0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
sample_retract_dist: 3.0
|
||||
samples_tolerance: 0.006
|
||||
samples_tolerance_retries: 3
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Print Cooling Fan - FAN0
|
||||
pin: PA8
|
||||
kick_start_time: 0.5
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
off_below: 0.10
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
## Hotend Fan - FAN1
|
||||
pin: PE5
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
## If you are experiencing back flow, you can reduce fan_speed
|
||||
#fan_speed: 1.0
|
||||
|
||||
[controller_fan controller_fan]
|
||||
## Controller fan - FAN2
|
||||
pin: PD12
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
|
||||
[heater_fan exhaust_fan]
|
||||
## Exhaust fan - FAN3
|
||||
pin: PD13
|
||||
max_power: 1.0
|
||||
shutdown_speed: 0.0
|
||||
kick_start_time: 5.0
|
||||
heater: heater_bed
|
||||
heater_temp: 60
|
||||
fan_speed: 1.0
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
## Chamber Lighting - HE2 Connector (Optional)
|
||||
#[output_pin caselight]
|
||||
#pin: PB10
|
||||
#pwm:true
|
||||
#shutdown_value: 0
|
||||
#value:1
|
||||
#cycle_time: 0.01
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
home_xy_position: 232.45, 358
|
||||
speed:100
|
||||
z_hop:10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
## Gantry Corners for 250mm Build
|
||||
## Uncomment for 250mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 310, 320
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,175
|
||||
# 200,175
|
||||
# 200,25
|
||||
|
||||
## Gantry Corners for 300mm Build
|
||||
## Uncomment for 300mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 360,370
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,225
|
||||
# 250,225
|
||||
# 250,25
|
||||
|
||||
## Gantry Corners for 350mm Build
|
||||
## Uncomment for 350mm build
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
410,420
|
||||
# Probe points
|
||||
points:
|
||||
50,25
|
||||
50,275
|
||||
300,275
|
||||
300,25
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
speed: 350
|
||||
horizontal_move_z: 5
|
||||
retries: 5
|
||||
retry_tolerance: 0.0075
|
||||
max_adjust: 10
|
||||
|
||||
########################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
########################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE8, EXP1_2=PE7,
|
||||
EXP1_3=PE9, EXP1_4=PE10,
|
||||
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
||||
EXP1_7=PE14, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PB1, EXP2_4=PA4,
|
||||
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
||||
EXP2_7=PC15, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<5V>
|
||||
|
||||
|
||||
####################################################################
|
||||
# Virtual SD Card
|
||||
####################################################################
|
||||
|
||||
# Print files without octoprint
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/.octoprint/uploads/
|
||||
|
||||
[menu __main __sdcard]
|
||||
type: vsdlist
|
||||
enable: {('virtual_sdcard' in printer)}
|
||||
name: Print Files
|
||||
#####################################################################
|
||||
# Displays
|
||||
#####################################################################
|
||||
|
||||
## Uncomment the display that you have
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
#[display]
|
||||
## RepRapDiscount 128x64 Full Graphic Smart Controller
|
||||
#lcd_type: st7920
|
||||
#cs_pin: EXP1_4
|
||||
#sclk_pin: EXP1_5
|
||||
#sid_pin: EXP1_3
|
||||
#menu_timeout: 40
|
||||
#encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
#click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
[display]
|
||||
# mini12864 LCD Display
|
||||
lcd_type: uc1701
|
||||
cs_pin: EXP1_3
|
||||
a0_pin: EXP1_4
|
||||
rst_pin: EXP1_5
|
||||
encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
click_pin: ^!EXP1_2
|
||||
contrast: 63
|
||||
spi_software_miso_pin: EXP2_1
|
||||
spi_software_mosi_pin: EXP2_6
|
||||
spi_software_sclk_pin: EXP2_2
|
||||
|
||||
[neopixel btt_mini12864]
|
||||
# To control Neopixel RGB in mini12864 display
|
||||
pin: EXP1_6
|
||||
chain_count: 3
|
||||
initial_RED: 0.1
|
||||
initial_GREEN: 0.5
|
||||
initial_BLUE: 0.0
|
||||
color_order: RGB
|
||||
|
||||
## Set RGB values on boot up for each Neopixel.
|
||||
## Index 1 = display, Index 2 and 3 = Knob
|
||||
[delayed_gcode setdisplayneopixel]
|
||||
initial_duration: 1
|
||||
gcode:
|
||||
SET_LED LED=btt_mini12864 RED=0 GREEN=0.2 BLUE=1 INDEX=1 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=2 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=0 GREEN=0.2 BLUE=1 INDEX=3
|
||||
|
||||
### menu move 10mm ###
|
||||
[menu __main __control __move_10mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 10mm
|
||||
|
||||
[menu __main __control __move_10mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
realtime: True
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 1mm ###
|
||||
[menu __main __control __move_1mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 1mm
|
||||
|
||||
[menu __main __control __move_1mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
realtime: True
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 0.1mm ###
|
||||
[menu __main __control __move_01mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 0.1mm
|
||||
|
||||
[menu __main __control __move_01mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
realtime: True
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
realtime: True
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G0 X340 Y340 F18000
|
||||
G28
|
||||
## Uncomment for for your size printer:
|
||||
#--------------------------------------------------------------------
|
||||
## Uncomment for 250mm build
|
||||
#G0 X125 Y125 Z30 F3600
|
||||
|
||||
## Uncomment for 300 build
|
||||
#G0 X150 Y150 Z30 F3600
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#G0 X175 Y175 Z30 F3600
|
||||
G0 Z20
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
[gcode_macro PURGE_LINE]
|
||||
gcode:
|
||||
G0 X0 Y0 F18000 ; move to print bed corner
|
||||
G92 E0
|
||||
G0 Z0.2 F3000 ; move to bed
|
||||
G1 X100 E20 F1000 ; intro line
|
||||
G92 E0
|
||||
|
||||
G1 E-0.5 F3600
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
G32 ; home all axes
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
|
||||
PURGE_LINE
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
# safe anti-stringing move coords
|
||||
{% set th = printer.toolhead %}
|
||||
{% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %}
|
||||
{% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %}
|
||||
{% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %}
|
||||
|
||||
SAVE_GCODE_STATE NAME=STATE_PRINT_END
|
||||
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-2.0 F3600 ; retract filament
|
||||
|
||||
TURN_OFF_HEATERS
|
||||
|
||||
G90 ; absolute positioning
|
||||
G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing
|
||||
G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear
|
||||
M107 ; turn off fan
|
||||
|
||||
BED_MESH_CLEAR
|
||||
RESTORE_GCODE_STATE NAME=STATE_PRINT_END
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 30.421
|
||||
#*# pid_ki = 2.386
|
||||
#*# pid_kd = 96.965
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 41.377
|
||||
#*# pid_ki = 0.857
|
||||
#*# pid_kd = 499.625
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*# position_endstop = -0.8
|
||||
Loading…
Reference in New Issue
Block a user