539 lines
14 KiB
INI
539 lines
14 KiB
INI
# This file contains common pin mappings for the BigTreeTech Octopus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Thermistor types [extruder] and [heater_bed] sections
|
|
## Probe pin [probe] section
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[adxl345]
|
|
cs_pin: rpi:None
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
probe_points:
|
|
175, 175, 50
|
|
|
|
[mcu]
|
|
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_4A0028000250534E4E313120-if00
|
|
restart_method: command
|
|
##--------------------------------------------------------------------
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 350
|
|
max_accel: 3000 #Max 4000
|
|
max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## B Stepper - Left
|
|
## Connected to MOTOR_0
|
|
## Endstop connected to DIAG_0
|
|
[input_shaper]
|
|
shaper_freq_x: 59.6
|
|
shaper_type_x: mzv
|
|
shaper_freq_y: 45
|
|
shaper_type_y: mzv
|
|
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
## Uncomment for 350mm build
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 40 #Max 100, default 25
|
|
second_homing_speed: 15
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## A Stepper - Right
|
|
## Connected to MOTOR_1
|
|
## Endstop connected to DIAG_1
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
## Uncomment for 350mm build
|
|
position_endstop: 358
|
|
position_max: 358
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 40 #Max 100, default 25
|
|
second_homing_speed: 15
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left
|
|
## Connected to MOTOR_2
|
|
## Endstop connected to DIAG_2
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
endstop_pin: PG10
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 230
|
|
|
|
## Uncomment below for 300mm build
|
|
#position_max: 280
|
|
|
|
## Uncomment below for 350mm build
|
|
position_max: 330
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -5
|
|
homing_speed: 8
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z1 Stepper - Rear Left
|
|
## Connected to MOTOR_3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z2 Stepper - Rear Right
|
|
## Connected to MOTOR_4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z3 Stepper - Front Right
|
|
## Connected to MOTOR_5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: false
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
## Connected to MOTOR_6
|
|
## Heater - HE0
|
|
## Thermistor - T0
|
|
[extruder]
|
|
step_pin: PE2
|
|
dir_pin: PE3
|
|
enable_pin: !PD4
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point
|
|
rotation_distance: 22.536398 #Bondtech 5mm Drive Gears
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
gear_ratio: 50:17 #BMG Gear Ratio
|
|
microsteps: 32
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
heater_pin: PA2
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
|
sensor_type: MAX31865
|
|
sensor_pin: PF8
|
|
spi_speed: 2000000
|
|
spi_software_sclk_pin: EXP2_2
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_miso_pin: EXP2_1
|
|
rtd_nominal_r: 100
|
|
rtd_reference_r: 430
|
|
rtd_num_of_wires: 4
|
|
#rtd_use_50Hz_filter: False
|
|
# The above parameters control the sensor parameters of MAX31865
|
|
# chips. The defaults for each parameter are next to the parameter
|
|
# name in the above list.
|
|
min_temp: 0
|
|
max_temp: 480
|
|
max_power: 1.0
|
|
min_extrude_temp: 170
|
|
#control = pid
|
|
#pid_kp = 26.213
|
|
#pid_ki = 1.304
|
|
#pid_kd = 131.721
|
|
## Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.038 # T.S: Calibrated 05.01.2021
|
|
pressure_advance_smooth_time: 0.040 # T.S: Calibrated 05.01.2021
|
|
|
|
## E0 on MOTOR6
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 extruder]
|
|
uart_pin: PE1
|
|
interpolate: false
|
|
run_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
## SSR Pin - HE1
|
|
## Thermistor - TB
|
|
heater_pin: PA3
|
|
## Validate the following thermistor type to make sure it is correct
|
|
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
#control: pid
|
|
#pid_kp: 58.437
|
|
#pid_ki: 2.347
|
|
#pid_kd: 363.769
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
## Inductive Probe
|
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
|
|
|
## Select the probe port by type:
|
|
## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V.
|
|
#pin: ~!PB7
|
|
## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO.
|
|
#pin: PG15
|
|
## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper
|
|
pin: ~PC5
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 0
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.006
|
|
samples_tolerance_retries: 3
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[fan]
|
|
## Print Cooling Fan - FAN0
|
|
pin: PA8
|
|
kick_start_time: 0.5
|
|
## Depending on your fan, you may need to increase this value
|
|
## if your fan will not start. Can change cycle_time (increase)
|
|
## if your fan is not able to slow down effectively
|
|
off_below: 0.10
|
|
|
|
[heater_fan hotend_fan]
|
|
## Hotend Fan - FAN1
|
|
pin: PE5
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
## If you are experiencing back flow, you can reduce fan_speed
|
|
#fan_speed: 1.0
|
|
|
|
[controller_fan controller_fan]
|
|
## Controller fan - FAN2
|
|
pin: PD12
|
|
kick_start_time: 0.5
|
|
heater: heater_bed
|
|
|
|
[heater_fan exhaust_fan]
|
|
## Exhaust fan - FAN3
|
|
pin: PD13
|
|
max_power: 1.0
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 60
|
|
fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
## Chamber Lighting - HE2 Connector (Optional)
|
|
#[output_pin caselight]
|
|
#pin: PB10
|
|
#pwm:true
|
|
#shutdown_value: 0
|
|
#value:1
|
|
#cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 232.45, 358
|
|
speed:100
|
|
z_hop:10
|
|
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
speed: 350
|
|
horizontal_move_z: 5
|
|
retries: 5
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 10
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
|
|
####################################################################
|
|
# Virtual SD Card
|
|
####################################################################
|
|
|
|
# Print files without octoprint
|
|
|
|
[virtual_sdcard]
|
|
path: ~/.octoprint/uploads/
|
|
|
|
[menu __main __sdcard]
|
|
type: vsdlist
|
|
enable: {('virtual_sdcard' in printer)}
|
|
name: Print Files
|
|
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.1
|
|
initial_GREEN: 0.5
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=0 GREEN=0.2 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0 GREEN=0.2 BLUE=1 INDEX=3
|
|
|
|
[output_pin beeper]
|
|
pin: EXP1_1
|
|
|
|
#####################################################################
|
|
# Menu
|
|
#####################################################################
|
|
[include menu.cfg]
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
[include macros.cfg]
|
|
|
|
#####################################################################
|
|
# Display
|
|
#####################################################################
|
|
[include display.cfg]
|
|
|
|
[save_variables]
|
|
filename: /home/pi/Voron2_Config/variables.cfg
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 30.421
|
|
#*# pid_ki = 2.386
|
|
#*# pid_kd = 96.965
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 41.377
|
|
#*# pid_ki = 0.857
|
|
#*# pid_kd = 499.625
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = -0.8
|