2012-06-02 20:44:17 +02:00
# ifndef CONFIGURATION_H
# define CONFIGURATION_H
2011-11-06 12:39:00 +01:00
2014-12-18 21:02:36 +01:00
# include "boards.h"
2015-02-02 01:06:38 +01:00
//===========================================================================
//============================= Getting Started =============================
//===========================================================================
/*
Here are some standard links for getting your machine calibrated :
2015-03-07 07:14:34 +01:00
* http : //reprap.org/wiki/Calibration
2015-02-02 01:06:38 +01:00
* http : //youtu.be/wAL9d7FgInk
* http : //calculator.josefprusa.cz
* http : //reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
* http : //www.thingiverse.com/thing:5573
* https : //sites.google.com/site/repraplogphase/calibration-of-your-reprap
* http : //www.thingiverse.com/thing:298812
*/
2013-05-02 18:22:58 +02:00
// This configuration file contains the basic settings.
// Advanced settings can be found in Configuration_adv.h
2012-02-07 20:23:43 +01:00
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
2011-11-06 12:39:00 +01:00
2013-09-23 23:29:46 +02:00
//===========================================================================
//============================= DELTA Printer ===============================
//===========================================================================
2014-02-14 12:48:24 +01:00
// For a Delta printer replace the configuration files with the files in the
2013-09-23 23:29:46 +02:00
// example_configurations/delta directory.
2013-12-08 21:34:56 +01:00
//
2013-09-23 23:29:46 +02:00
2014-06-23 17:09:57 +02:00
//===========================================================================
//============================= SCARA Printer ===============================
//===========================================================================
2015-04-05 00:26:35 +02:00
// For a Scara printer replace the configuration files with the files in the
2014-06-23 17:09:57 +02:00
// example_configurations/SCARA directory.
//
2015-04-04 13:15:42 +02:00
// @section info
2013-05-02 18:22:58 +02:00
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
// build by the user have been successfully uploaded into firmware.
2015-04-08 05:38:43 +02:00
# define STRING_VERSION "1.0.3 dev"
2012-11-12 22:06:59 +01:00
# define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
2013-05-02 18:22:58 +02:00
# define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
2015-02-03 12:25:36 +01:00
# define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1
//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2
2011-11-09 20:28:40 +01:00
2015-04-04 13:15:42 +02:00
// @section machine
2012-11-05 12:15:07 +01:00
// SERIAL_PORT selects which serial port should be used for communication with the host.
// This allows the connection of wireless adapters (for instance) to non-default port pins.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
2015-04-04 13:15:42 +02:00
// :[0,1,2,3,4,5,6,7]
2012-11-05 12:15:07 +01:00
# define SERIAL_PORT 0
2011-11-09 20:28:40 +01:00
// This determines the communication speed of the printer
2015-04-04 13:15:42 +02:00
// :[2400,9600,19200,38400,57600,115200,250000]
2012-02-25 17:44:45 +01:00
# define BAUDRATE 250000
2013-10-30 11:45:32 +01:00
// This enables the serial port associated to the Bluetooth interface
2013-11-03 19:57:06 +01:00
//#define BTENABLED // Enable BT interface on AT90USB devices
2013-10-30 11:45:32 +01:00
2014-12-18 21:02:36 +01:00
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
2012-03-22 14:48:10 +01:00
# ifndef MOTHERBOARD
2015-03-10 19:06:34 +01:00
# define MOTHERBOARD BOARD_RAMPS_13_EFB
2012-03-22 14:48:10 +01:00
# endif
2011-11-06 19:30:04 +01:00
2015-04-11 06:29:42 +02:00
// Optional custom name for your RepStrap or other custom machine
// Displayed in the LCD "Ready" message
2015-04-13 02:17:41 +02:00
// #define CUSTOM_MACHINE_NAME "3D Printer"
2013-05-02 18:22:58 +02:00
2013-11-01 21:51:50 +01:00
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
2013-06-07 00:49:25 +02:00
// This defines the number of extruders
2015-04-04 13:15:42 +02:00
// :[1,2,3,4]
2013-06-07 00:49:25 +02:00
# define EXTRUDERS 1
2015-03-31 11:49:47 +02:00
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
2015-03-31 11:50:52 +02:00
//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
2015-03-31 11:49:47 +02:00
2013-01-07 14:33:30 +01:00
//// The following define selects which power supply you have. Please choose the one that matches your setup
// 1 = ATX
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
2015-04-04 13:15:42 +02:00
// :{1:'ATX',2:'X-Box 360'}
2012-07-14 13:43:19 +02:00
2013-01-07 14:33:30 +01:00
# define POWER_SUPPLY 1
2012-07-14 13:43:19 +02:00
2014-02-14 12:48:24 +01:00
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
2013-10-29 18:44:56 +01:00
// #define PS_DEFAULT_OFF
2015-04-04 13:15:42 +02:00
// @section temperature
2011-11-09 20:28:40 +01:00
//===========================================================================
2015-02-02 01:06:38 +01:00
//============================= Thermal Settings ============================
2011-11-09 20:28:40 +01:00
//===========================================================================
2012-05-20 12:27:52 +02:00
//
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
//
2012-02-07 20:23:43 +01:00
//// Temperature sensor settings:
// -2 is thermocouple with MAX6675 (only for sensor 0)
// -1 is thermocouple with AD595
// 0 is not used
2012-05-20 12:27:52 +02:00
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
2014-02-14 12:48:24 +01:00
// 3 is Mendel-parts thermistor (4.7k pullup)
2012-02-08 18:38:45 +01:00
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
2013-11-01 21:51:50 +01:00
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
2012-05-20 12:27:52 +02:00
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
2013-07-30 14:01:41 +02:00
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
2012-12-30 12:09:38 +01:00
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
2014-04-13 17:03:20 +02:00
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
2014-04-24 10:49:42 +02:00
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
2015-03-31 08:24:33 +02:00
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
2014-02-13 10:53:46 +01:00
// 20 is the PT100 circuit found in the Ultimainboard V2.x
2014-03-27 04:41:10 +01:00
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
2012-05-20 12:27:52 +02:00
//
2013-06-07 00:49:25 +02:00
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
2012-05-20 12:27:52 +02:00
// (but gives greater accuracy and more stable PID)
// 51 is 100k thermistor - EPCOS (1k pullup)
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
2013-11-01 21:51:50 +01:00
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
2014-02-14 12:15:31 +01:00
//
// 1047 is Pt1000 with 4k7 pullup
// 1010 is Pt1000 with 1k pullup (non standard)
// 147 is Pt100 with 4k7 pullup
// 110 is Pt100 with 1k pullup (non standard)
2015-03-31 08:24:33 +02:00
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
2015-02-24 11:02:16 +01:00
// Use it for Testing or Development purposes. NEVER for production machine.
// #define DUMMY_THERMISTOR_998_VALUE 25
// #define DUMMY_THERMISTOR_999_VALUE 100
2015-04-08 12:12:21 +02:00
// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
2015-03-10 18:41:21 +01:00
# define TEMP_SENSOR_0 1
# define TEMP_SENSOR_1 0
2012-02-07 20:23:43 +01:00
# define TEMP_SENSOR_2 0
2015-02-08 09:05:05 +01:00
# define TEMP_SENSOR_3 0
2012-02-26 16:23:47 +01:00
# define TEMP_SENSOR_BED 0
2011-11-06 12:39:00 +01:00
2013-06-07 00:49:25 +02:00
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
2013-08-01 15:06:39 +02:00
//#define TEMP_SENSOR_1_AS_REDUNDANT
2013-06-07 00:49:25 +02:00
# define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
2011-11-09 20:28:40 +01:00
// Actual temperature must be close to target for this long before M109 returns success
2013-06-07 00:49:25 +02:00
# define TEMP_RESIDENCY_TIME 10 // (seconds)
2012-02-23 18:45:37 +01:00
# define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
2013-05-02 18:22:58 +02:00
# define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
2011-11-06 12:39:00 +01:00
2012-02-07 20:23:43 +01:00
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
2013-06-07 00:49:25 +02:00
// to check that the wiring to the thermistor is not broken.
2012-02-07 20:23:43 +01:00
// Otherwise this would lead to the heater being powered on all the time.
2011-11-09 20:28:40 +01:00
# define HEATER_0_MINTEMP 5
2012-02-07 20:23:43 +01:00
# define HEATER_1_MINTEMP 5
# define HEATER_2_MINTEMP 5
2015-02-08 09:05:05 +01:00
# define HEATER_3_MINTEMP 5
2012-02-07 20:23:43 +01:00
# define BED_MINTEMP 5
2011-11-06 12:39:00 +01:00
2011-11-09 20:28:40 +01:00
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
# define HEATER_0_MAXTEMP 275
2012-02-07 20:23:43 +01:00
# define HEATER_1_MAXTEMP 275
# define HEATER_2_MAXTEMP 275
2015-02-08 09:05:05 +01:00
# define HEATER_3_MAXTEMP 275
2012-02-07 20:23:43 +01:00
# define BED_MAXTEMP 150
2011-12-12 19:34:37 +01:00
2012-08-11 08:17:47 +02:00
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
2012-02-16 11:03:41 +01:00
2014-02-05 10:47:12 +01:00
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
2014-02-03 20:46:09 +01:00
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
2015-02-02 01:06:38 +01:00
//===========================================================================
//============================= PID Settings ================================
//===========================================================================
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
2012-02-07 20:23:43 +01:00
// Comment the following line to disable PID and enable bang-bang.
2011-11-09 20:28:40 +01:00
# define PIDTEMP
2013-06-09 00:51:58 +02:00
# define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
2014-06-24 23:03:55 +02:00
# define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
2011-11-09 20:28:40 +01:00
# ifdef PIDTEMP
2013-06-07 00:49:25 +02:00
//#define PID_DEBUG // Sends debug data to the serial port.
2012-09-13 04:01:31 +02:00
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
2015-01-07 21:41:09 +01:00
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
2015-01-11 03:50:17 +01:00
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with gcode: M301 E[extruder number, 0-2]
2012-12-12 09:08:37 +01:00
# define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
2014-06-24 23:03:55 +02:00
# define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
2013-05-02 18:22:58 +02:00
# define K1 0.95 //smoothing factor within the PID
2011-11-09 20:28:40 +01:00
2014-02-14 12:48:24 +01:00
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
2012-02-07 20:23:43 +01:00
// Ultimaker
2012-03-25 14:36:51 +02:00
# define DEFAULT_Kp 22.2
2013-06-07 00:49:25 +02:00
# define DEFAULT_Ki 1.08
# define DEFAULT_Kd 114
2011-12-06 05:33:33 +01:00
2014-02-14 12:48:24 +01:00
// MakerGear
2011-12-12 19:34:37 +01:00
// #define DEFAULT_Kp 7.0
2013-06-07 00:49:25 +02:00
// #define DEFAULT_Ki 0.1
// #define DEFAULT_Kd 12
2011-11-18 18:59:17 +01:00
2013-06-07 00:49:25 +02:00
// Mendel Parts V9 on 12V
2012-03-25 14:36:51 +02:00
// #define DEFAULT_Kp 63.0
// #define DEFAULT_Ki 2.25
// #define DEFAULT_Kd 440
2011-11-09 20:28:40 +01:00
# endif // PIDTEMP
2011-11-06 12:39:00 +01:00
2015-02-02 01:06:38 +01:00
//===========================================================================
//============================= PID > Bed Temperature Control ===============
//===========================================================================
2013-05-02 18:22:58 +02:00
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
2012-09-17 21:17:24 +02:00
//
2013-05-02 18:22:58 +02:00
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
2015-03-25 11:51:41 +01:00
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
2012-09-17 21:17:24 +02:00
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
2013-06-07 00:49:25 +02:00
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
2012-09-17 21:17:24 +02:00
// shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below.
//#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING
2013-05-02 18:22:58 +02:00
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
2012-09-17 21:17:24 +02:00
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
# define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
2015-02-10 14:13:06 +01:00
//#define PID_BED_DEBUG // Sends debug data to the serial port.
2012-09-17 21:17:24 +02:00
# ifdef PIDTEMPBED
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
2013-05-02 18:22:58 +02:00
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
2012-09-13 04:01:31 +02:00
# define DEFAULT_bedKp 10.00
# define DEFAULT_bedKi .023
# define DEFAULT_bedKd 305.4
2012-09-17 21:17:24 +02:00
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from pidautotune
2012-09-13 04:01:31 +02:00
// #define DEFAULT_bedKp 97.1
// #define DEFAULT_bedKi 1.41
// #define DEFAULT_bedKd 1675.16
2012-09-17 21:17:24 +02:00
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
# endif // PIDTEMPBED
2015-04-04 13:15:42 +02:00
// @section extruder
2012-09-17 21:17:24 +02:00
2012-02-07 20:23:43 +01:00
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
# define PREVENT_DANGEROUS_EXTRUDE
2012-05-08 17:27:45 +02:00
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
# define PREVENT_LENGTHY_EXTRUDE
2012-02-12 17:38:54 +01:00
# define EXTRUDE_MINTEMP 170
2012-02-07 20:23:43 +01:00
# define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
2011-11-06 12:39:00 +01:00
2015-02-02 01:06:38 +01:00
//===========================================================================
//============================= Thermal Runaway Protection ==================
//===========================================================================
/*
2014-06-30 20:22:37 +02:00
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place ( this happened to a friend of mine recently and
motivated me writing this feature ) .
The issue : If a thermistor come off , it will read a lower temperature than actual .
The system will turn the heater on forever , burning up the filament and anything
else around .
2015-03-31 08:24:33 +02:00
After the temperature reaches the target for the first time , this feature will
start measuring for how long the current temperature stays below the target
2014-06-30 20:22:37 +02:00
minus _HYSTERESIS ( set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS ) .
If it stays longer than _PERIOD , it means the thermistor temperature
cannot catch up with the target , so something * may be * wrong . Then , to be on the
safe side , the system will he halt .
2015-03-31 08:24:33 +02:00
Bear in mind the count down will just start AFTER the first time the
2014-06-30 20:22:37 +02:00
thermistor temperature is over the target , so you will have no problem if
your extruder heater takes 2 minutes to hit the target on heating .
*/
// If you want to enable this feature for all your extruder heaters,
// uncomment the 2 defines below:
// Parameters for all extruder heaters
//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater,
// uncomment the 2 defines below:
// Parameters for the bed heater
//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
2011-11-09 20:28:40 +01:00
//===========================================================================
2015-02-02 01:06:38 +01:00
//============================= Mechanical Settings =========================
2011-11-09 20:28:40 +01:00
//===========================================================================
2015-04-04 13:15:42 +02:00
// @section machine
2015-03-07 07:14:34 +01:00
// Uncomment this option to enable CoreXY kinematics
2012-07-14 14:21:53 +02:00
// #define COREXY
2015-03-07 07:14:34 +01:00
// Enable this option for Toshiba steppers
// #define CONFIG_STEPPERS_TOSHIBA
2015-04-04 13:15:42 +02:00
// @section homing
2015-03-31 06:15:16 +02:00
// coarse Endstop Settings
# define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
# ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
2015-03-31 07:11:11 +02:00
// #define ENDSTOPPULLUP_ZPROBE
2015-03-31 06:15:16 +02:00
# endif
2015-03-10 18:41:21 +01:00
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
2015-03-29 09:29:16 +02:00
const bool Z_PROBE_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
2012-04-15 19:17:33 +02:00
//#define DISABLE_MAX_ENDSTOPS
2013-06-18 19:20:26 +02:00
//#define DISABLE_MIN_ENDSTOPS
2015-04-04 13:15:42 +02:00
// @section machine
2015-03-29 09:29:16 +02:00
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
2015-04-01 09:14:55 +02:00
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
2015-03-29 09:29:16 +02:00
// this has no effect.
//#define DISABLE_Z_PROBE_ENDSTOP
2011-11-06 12:39:00 +01:00
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
2015-04-04 13:15:42 +02:00
// :{0:'Low',1:'High'}
2011-11-06 12:39:00 +01:00
# define X_ENABLE_ON 0
# define Y_ENABLE_ON 0
# define Z_ENABLE_ON 0
2011-12-06 05:33:33 +01:00
# define E_ENABLE_ON 0 // For all extruders
2011-11-06 12:39:00 +01:00
// Disables axis when it's not being used.
2015-04-25 09:46:33 +02:00
// WARNING: When motors turn off there is a chance of losing position accuracy!
2011-11-06 12:39:00 +01:00
# define DISABLE_X false
# define DISABLE_Y false
2011-12-12 19:34:37 +01:00
# define DISABLE_Z false
2015-04-04 13:15:42 +02:00
// @section extruder
2011-12-06 05:33:33 +01:00
# define DISABLE_E false // For all extruders
2014-06-02 14:07:02 +02:00
# define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
2011-11-06 12:39:00 +01:00
2015-04-04 13:15:42 +02:00
// @section machine
2015-03-31 08:24:33 +02:00
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
2015-03-10 18:41:21 +01:00
# define INVERT_X_DIR false
# define INVERT_Y_DIR false
# define INVERT_Z_DIR false
2015-04-04 13:15:42 +02:00
// @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
2015-03-10 18:41:21 +01:00
# define INVERT_E0_DIR false
# define INVERT_E1_DIR false
# define INVERT_E2_DIR false
# define INVERT_E3_DIR false
2011-11-06 12:39:00 +01:00
2015-04-04 13:15:42 +02:00
// @section homing
2012-02-07 20:23:43 +01:00
// ENDSTOP SETTINGS:
2011-11-06 12:39:00 +01:00
// Sets direction of endstops when homing; 1=MAX, -1=MIN
2015-04-04 13:15:42 +02:00
// :[-1,1]
2011-11-06 12:39:00 +01:00
# define X_HOME_DIR -1
# define Y_HOME_DIR -1
# define Z_HOME_DIR -1
2013-05-02 18:22:58 +02:00
# define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
# define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
2013-09-29 18:20:06 +02:00
2015-04-04 13:15:42 +02:00
// @section machine
2015-02-02 01:06:38 +01:00
// Travel limits after homing (units are in mm)
2013-11-28 01:37:35 +01:00
# define X_MIN_POS 0
# define Y_MIN_POS 0
# define Z_MIN_POS 0
2015-03-11 23:47:32 +01:00
# define X_MAX_POS 200
# define Y_MAX_POS 200
2015-03-07 10:07:40 +01:00
# define Z_MAX_POS 200
2013-11-28 01:37:35 +01:00
2015-03-07 21:43:15 +01:00
//===========================================================================
//============================= Filament Runout Sensor ======================
//===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
// It is assumed that when logic high = filament available
// when logic low = filament ran out
2015-04-29 21:38:40 +02:00
# ifdef FILAMENT_RUNOUT_SENSOR
const bool FIL_RUNOUT_INVERTING = true ; // Should be uncommented and true or false should assigned
# define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
# define FILAMENT_RUNOUT_SCRIPT "M600"
# endif
2015-02-02 01:06:38 +01:00
2015-03-15 10:43:26 +01:00
//===========================================================================
2015-04-08 20:52:48 +02:00
//============================ Mesh Bed Leveling ============================
2015-03-15 10:43:26 +01:00
//===========================================================================
2015-03-16 02:50:11 +01:00
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
// #define MESH_BED_LEVELING // Enable mesh bed leveling
2015-03-15 10:43:26 +01:00
2015-04-05 04:06:02 +02:00
# ifdef MANUAL_BED_LEVELING
2015-04-05 05:14:06 +02:00
# define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
2015-04-01 21:18:51 +02:00
# endif // MANUAL_BED_LEVELING
2015-04-04 00:31:35 +02:00
# ifdef MESH_BED_LEVELING
2015-03-15 10:43:26 +01:00
# define MESH_MIN_X 10
# define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
# define MESH_MIN_Y 10
# define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y)
2015-03-16 01:48:46 +01:00
# define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited
2015-03-15 10:43:26 +01:00
# define MESH_NUM_Y_POINTS 3
2015-03-15 23:18:11 +01:00
# define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0
2015-03-15 10:43:26 +01:00
# endif // MESH_BED_LEVELING
2015-02-02 01:06:38 +01:00
//===========================================================================
2014-12-21 13:06:05 +01:00
//============================= Bed Auto Leveling ===========================
2015-02-02 01:06:38 +01:00
//===========================================================================
2013-09-29 18:20:06 +02:00
2015-04-04 13:15:42 +02:00
// @section bedlevel
2014-12-21 13:06:05 +01:00
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
# define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
2013-09-29 18:20:06 +02:00
2014-12-21 13:06:05 +01:00
# ifdef ENABLE_AUTO_BED_LEVELING
2013-09-29 18:20:06 +02:00
2015-03-07 07:14:34 +01:00
// There are 2 different ways to specify probing locations
//
// - "grid" mode
// Probe several points in a rectangular grid.
// You specify the rectangle and the density of sample points.
// This mode is preferred because there are more measurements.
//
// - "3-point" mode
// Probe 3 arbitrary points on the bed (that aren't colinear)
// You specify the XY coordinates of all 3 points.
// Enable this to sample the bed in a grid (least squares solution)
// Note: this feature generates 10KB extra code size
2014-12-21 13:06:05 +01:00
# define AUTO_BED_LEVELING_GRID
2015-03-07 07:14:34 +01:00
2014-12-21 13:06:05 +01:00
# ifdef AUTO_BED_LEVELING_GRID
2014-02-20 06:12:39 +01:00
# define LEFT_PROBE_BED_POSITION 15
# define RIGHT_PROBE_BED_POSITION 170
# define FRONT_PROBE_BED_POSITION 20
2015-03-07 07:14:34 +01:00
# define BACK_PROBE_BED_POSITION 170
2015-03-31 08:24:33 +02:00
2015-03-10 18:08:32 +01:00
# define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
2014-02-20 06:12:39 +01:00
2015-03-07 07:14:34 +01:00
// Set the number of grid points per dimension
// You probably don't need more than 3 (squared=9)
2014-12-21 13:06:05 +01:00
# define AUTO_BED_LEVELING_GRID_POINTS 2
2014-02-20 06:12:39 +01:00
2015-03-07 07:14:34 +01:00
# else // !AUTO_BED_LEVELING_GRID
2014-02-20 06:12:39 +01:00
2015-03-07 07:14:34 +01:00
// Arbitrary points to probe. A simple cross-product
// is used to estimate the plane of the bed.
2014-02-20 06:12:39 +01:00
# define ABL_PROBE_PT_1_X 15
# define ABL_PROBE_PT_1_Y 180
# define ABL_PROBE_PT_2_X 15
# define ABL_PROBE_PT_2_Y 20
# define ABL_PROBE_PT_3_X 170
# define ABL_PROBE_PT_3_Y 20
2014-12-21 13:06:05 +01:00
# endif // AUTO_BED_LEVELING_GRID
2013-09-29 18:20:06 +02:00
2015-03-07 07:14:34 +01:00
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
2014-12-31 19:34:59 +01:00
// X and Y offsets must be integers
2015-03-10 18:08:32 +01:00
# define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right
# define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind
2015-03-05 06:32:11 +01:00
# define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
2013-10-12 22:28:11 +02:00
# define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
// Be sure you have this distance over your Z_MAX_POS in case
2013-12-08 21:34:56 +01:00
2013-09-29 18:20:06 +02:00
# define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min
2013-12-08 21:34:56 +01:00
2015-03-31 08:24:33 +02:00
# define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
2013-09-29 18:20:06 +02:00
# define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
2015-03-07 19:55:30 +01:00
# define Z_RAISE_AFTER_PROBING 15 //How much the extruder will be raised after the last probing point.
2013-09-29 18:20:06 +02:00
2015-03-10 18:41:21 +01:00
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
2015-03-10 18:08:32 +01:00
//Useful to retract a deployable probe.
2014-08-04 16:18:25 +02:00
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
2013-09-29 18:20:06 +02:00
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
2013-12-08 21:34:56 +01:00
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
2013-11-28 01:37:35 +01:00
2014-12-21 13:06:05 +01:00
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
2013-11-28 01:37:35 +01:00
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
2013-12-08 21:34:56 +01:00
# define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
2013-11-28 01:37:35 +01:00
// When defined, it will:
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled
// - If stepper drivers timeout, it will need X and Y homing again before Z homing
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
// - Block Z homing only when the probe is outside bed area.
2013-12-08 21:34:56 +01:00
2013-11-28 01:37:35 +01:00
# ifdef Z_SAFE_HOMING
2013-12-08 21:34:56 +01:00
2013-11-28 01:37:35 +01:00
# define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH / 2) // X point for Z homing when homing all axis (G28)
# define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH / 2) // Y point for Z homing when homing all axis (G28)
2013-12-08 21:34:56 +01:00
2013-11-28 01:37:35 +01:00
# endif
2013-12-08 21:34:56 +01:00
2015-04-04 03:14:57 +02:00
// Support for a dedicated Z PROBE endstop separate from the Z MIN endstop.
// If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below.
// If you want to still use the Z min endstop for homing, disable Z_SAFE_HOMING above. Eg; to park the head outside the bed area when homing with G28.
// WARNING: The Z MIN endstop will need to set properly as it would without a Z PROBE to prevent head crashes and premature stopping during a print.
2015-04-04 07:54:48 +02:00
// To use a separate Z PROBE endstop, you must have a Z_PROBE_PIN defined in the pins.h file for your control board.
2015-04-04 03:14:57 +02:00
// If you are using a servo based Z PROBE, you will need to enable NUM_SERVOS, SERVO_ENDSTOPS and SERVO_ENDSTOPS_ANGLES in the R/C Servo below.
// RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board. Use 5V for powered sensors, otherwise connect to ground and D32
// for normally closed configuration and 5V and D32 for normally open configurations. Normally closed configuration is advised and assumed.
// The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
// D32 is currently selected in the RAMPS 1.3/1.4 pin file. All other boards will need changes to the respective pins_XXXXX.h file.
// WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework.
//#define Z_PROBE_ENDSTOP
2015-03-28 10:31:51 +01:00
2014-12-21 13:06:05 +01:00
# endif // ENABLE_AUTO_BED_LEVELING
2013-09-29 18:20:06 +02:00
2011-11-06 12:39:00 +01:00
2015-04-04 13:15:42 +02:00
// @section homing
2012-09-15 06:48:49 +02:00
// The position of the homing switches
2012-12-11 10:54:40 +01:00
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
2012-09-15 06:48:49 +02:00
2015-03-07 10:07:40 +01:00
// Manual homing switch locations:
2014-02-14 12:48:24 +01:00
// For deltabots this means top and center of the Cartesian print volume.
2015-03-07 10:07:40 +01:00
# ifdef MANUAL_HOME_POSITIONS
# define MANUAL_X_HOME_POS 0
# define MANUAL_Y_HOME_POS 0
# define MANUAL_Z_HOME_POS 0
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
# endif
2012-02-22 18:07:56 +01:00
2015-04-04 13:15:42 +02:00
// @section movement
2015-04-04 05:45:24 +02:00
/**
* MOVEMENT SETTINGS
*/
2012-02-26 16:23:47 +01:00
# define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
2011-11-06 19:23:08 +01:00
2013-06-07 00:49:25 +02:00
// default settings
2011-11-06 12:39:00 +01:00
2015-03-10 18:41:21 +01:00
# define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
# define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
# define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
2011-11-06 12:39:00 +01:00
2015-03-11 17:19:02 +01:00
# define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
# define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
# define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
2011-11-06 12:39:00 +01:00
2013-05-02 18:55:15 +02:00
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
2011-11-27 21:12:55 +01:00
# define DEFAULT_XYJERK 20.0 // (mm/sec)
2011-11-13 20:42:08 +01:00
# define DEFAULT_ZJERK 0.4 // (mm/sec)
2012-03-04 16:34:58 +01:00
# define DEFAULT_EJERK 5.0 // (mm/sec)
2011-11-06 12:39:00 +01:00
2015-02-02 01:06:38 +01:00
//=============================================================================
//============================= Additional Features ===========================
//=============================================================================
2011-11-06 12:39:00 +01:00
2015-04-04 13:15:42 +02:00
// @section more
2014-02-19 23:59:10 +01:00
// Custom M code points
# define CUSTOM_M_CODES
# ifdef CUSTOM_M_CODES
2015-03-26 05:20:50 +01:00
# ifdef ENABLE_AUTO_BED_LEVELING
# define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
2015-03-26 21:52:48 +01:00
# define Z_PROBE_OFFSET_RANGE_MIN -20
# define Z_PROBE_OFFSET_RANGE_MAX 20
2015-03-26 05:20:50 +01:00
# endif
2014-02-19 23:59:10 +01:00
# endif
2015-04-04 13:15:42 +02:00
// @section extras
2014-02-19 23:59:10 +01:00
2011-11-09 20:28:40 +01:00
// EEPROM
2014-02-14 12:48:24 +01:00
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
2013-06-07 00:49:25 +02:00
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
2011-11-09 20:28:40 +01:00
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
2014-02-14 12:48:24 +01:00
//define this to enable EEPROM support
2012-02-26 16:23:47 +01:00
//#define EEPROM_SETTINGS
2015-04-07 06:46:18 +02:00
# ifdef EEPROM_SETTINGS
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
# define EEPROM_CHITCHAT // please keep turned on if you can.
# endif
2011-11-06 12:39:00 +01:00
2015-04-04 13:15:42 +02:00
// @section temperature
2013-06-07 00:49:25 +02:00
// Preheat Constants
2013-08-01 15:06:39 +02:00
# define PLA_PREHEAT_HOTEND_TEMP 180
2013-06-07 00:49:25 +02:00
# define PLA_PREHEAT_HPB_TEMP 70
2015-03-10 18:41:21 +01:00
# define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
2013-06-07 00:49:25 +02:00
# define ABS_PREHEAT_HOTEND_TEMP 240
2015-03-10 18:41:21 +01:00
# define ABS_PREHEAT_HPB_TEMP 110
# define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
2013-06-07 00:49:25 +02:00
2015-02-08 13:45:22 +01:00
//==============================LCD and SD support=============================
2015-04-04 13:15:42 +02:00
// @section lcd
2015-02-08 13:45:22 +01:00
// Define your display language below. Replace (en) with your language code and uncomment.
2015-04-27 12:15:36 +02:00
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
2015-02-08 13:45:22 +01:00
// See also language.h
2015-03-13 14:26:58 +01:00
# define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
2015-01-30 10:28:22 +01:00
2015-03-31 08:24:33 +02:00
// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
2015-03-13 14:26:58 +01:00
// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
2015-03-17 11:23:44 +01:00
// See also documentation/LCDLanguageFont.md
2015-03-11 11:10:35 +01:00
# define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware
//#define DISPLAY_CHARSET_HD44780_WESTERN
2015-03-17 11:23:44 +01:00
//#define DISPLAY_CHARSET_HD44780_CYRILLIC
2015-01-30 10:28:22 +01:00
2014-02-14 12:48:24 +01:00
//#define ULTRA_LCD //general LCD support, also 16x2
2013-06-07 00:49:25 +02:00
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
2012-02-26 22:05:38 +01:00
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
2013-04-24 10:50:57 +02:00
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
2014-05-01 12:03:41 +02:00
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
2013-09-23 23:25:11 +02:00
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
2013-12-08 21:34:56 +01:00
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
2014-02-14 12:48:24 +01:00
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
//#define ULTIPANEL //the UltiPanel as on Thingiverse
2014-02-03 08:45:03 +01:00
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
2015-04-20 11:11:13 +02:00
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
2014-07-29 19:56:55 +02:00
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
// http://reprap.org/wiki/PanelOne
//#define PANEL_ONE
2013-07-14 10:17:55 +02:00
// The MaKr3d Makr-Panel with graphic controller and SD support
// http://reprap.org/wiki/MaKr3d_MaKrPanel
//#define MAKRPANEL
2015-02-08 11:14:59 +01:00
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
// http://panucatt.com
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define VIKI2
//#define miniVIKI
2013-01-08 17:09:57 +01:00
// The RepRapDiscount Smart Controller (white PCB)
2012-11-07 02:32:13 +01:00
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
2015-04-20 15:01:43 +02:00
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
2013-03-05 15:51:24 +01:00
// The GADGETS3D G3D LCD/SD Controller (blue PCB)
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
2013-01-08 17:09:57 +01:00
//#define G3D_PANEL
2012-11-07 02:32:13 +01:00
2013-04-16 14:21:39 +02:00
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
2013-06-07 00:49:25 +02:00
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
//#define REPRAPWORLD_KEYPAD
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
2013-05-06 16:44:38 +02:00
// The Elefu RA Board Control Panel
// http://www.elefu.com/index.php?route=product/product&product_id=53
2015-01-06 21:55:08 +01:00
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
2013-05-07 07:23:54 +02:00
//#define RA_CONTROL_PANEL
2013-05-06 16:44:38 +02:00
2015-03-20 06:22:23 +01:00
/**
* I2C Panels
*/
2012-11-11 11:06:58 +01:00
2013-06-07 00:49:25 +02:00
//#define LCD_I2C_SAINSMART_YWROBOT
2012-11-11 11:06:58 +01:00
2013-06-07 00:49:25 +02:00
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
//#define LCD_I2C_PANELOLU2
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
//#define LCD_I2C_VIKI
2012-04-22 20:55:56 +02:00
2013-10-30 11:45:32 +01:00
// Shift register panels
// ---------------------
2013-11-03 19:57:06 +01:00
// 2 wire Non-latching LCD SR from:
2015-03-31 08:24:33 +02:00
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
2014-12-28 19:54:06 +01:00
//#define SAV_3DLCD
2013-07-14 10:28:26 +02:00
2015-04-04 13:15:42 +02:00
// @section extras
2012-05-02 19:26:14 +02:00
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
2012-08-11 15:51:04 +02:00
//#define FAST_PWM_FAN
2012-05-02 19:26:14 +02:00
2013-06-09 12:52:49 +02:00
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
2015-03-31 08:24:33 +02:00
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
2013-06-09 12:52:49 +02:00
// is too low, you should also increment SOFT_PWM_SCALE.
//#define FAN_SOFT_PWM
// Incrementing this by 1 will double the software PWM frequency,
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
// However, control resolution will be halved for each increment;
// at zero value, there are 128 effective control positions.
# define SOFT_PWM_SCALE 0
2015-03-20 06:22:23 +01:00
// Temperature status LEDs that display the hotend and bet temperature.
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
// Otherwise the RED led is on. There is 1C hysteresis.
//#define TEMP_STAT_LEDS
2011-12-22 12:11:39 +01:00
// M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23
2015-04-04 00:31:35 +02:00
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
2012-09-02 01:12:49 +02:00
//#define SF_ARC_FIX
2013-06-07 00:49:25 +02:00
// Support for the BariCUDA Paste Extruder.
//#define BARICUDA
2013-09-10 11:18:29 +02:00
//define BlinkM/CyzRgb Support
2013-09-20 09:57:42 +02:00
//#define BLINKM
2013-09-10 11:18:29 +02:00
2013-06-07 00:49:25 +02:00
/*********************************************************************\
* R / C SERVO support
* Sponsored by TrinityLabs , Reworked by codexmas
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
// Number of servos
//
// If you select a configuration below, this will receive a default value and does not need to be set manually
// set it manually if you have more servos than extruders and wish to manually control some
// leaving it undefined or defining as 0 will disable the servo subsystem
// If unsure, leave commented / disabled
//
2013-06-09 23:10:41 +02:00
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
2013-06-06 16:36:52 +02:00
// Servo Endstops
2013-08-01 15:06:39 +02:00
//
2013-06-06 16:36:52 +02:00
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
2015-03-31 12:20:15 +02:00
// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500.
2013-08-01 15:06:39 +02:00
//
2013-06-06 16:36:52 +02:00
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
2013-06-07 00:49:25 +02:00
2014-08-07 02:30:57 +02:00
/**********************************************************************\
* Support for a filament diameter sensor
* Also allows adjustment of diameter at print time ( vs at slicing )
* Single extruder only at this point ( extruder 0 )
2015-03-31 08:24:33 +02:00
*
2014-08-07 02:30:57 +02:00
* Motherboards
2015-03-31 08:24:33 +02:00
* 34 - RAMPS1 .4 - uses Analog input 5 on the AUX2 connector
2014-11-11 04:43:58 +01:00
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector ( version B , C , D , E )
2014-08-07 02:30:57 +02:00
* 301 - Rambo - uses Analog input 3
* Note may require analog pins to be defined for different motherboards
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
2014-11-09 20:26:02 +01:00
// Uncomment below to enable
//#define FILAMENT_SENSOR
2015-04-20 15:01:43 +02:00
# define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
# define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
2014-08-07 02:30:57 +02:00
2015-04-20 15:01:43 +02:00
# define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
# define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm
# define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm
# define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
2014-08-07 02:30:57 +02:00
//defines used in the code
2015-03-31 08:24:33 +02:00
# define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
2014-08-07 02:30:57 +02:00
2014-11-11 04:43:58 +01:00
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
//#define FILAMENT_LCD_DISPLAY
2014-08-07 02:30:57 +02:00
2012-02-07 20:23:43 +01:00
# include "Configuration_adv.h"
2015-01-16 16:48:22 +01:00
# include "thermistortables.h"
2011-11-09 20:28:40 +01:00
2015-03-20 06:22:23 +01:00
# endif //CONFIGURATION_H