Merge pull request #7079 from thinkyhead/bf_m600_fixes

M600 fixes

Marlin/Marlin_main.cpp

@@ -5866,7 +5866,7 @@ inline void gcode_M17() {
       idle();
       heaters_heating = false;
       HOTEND_LOOP() {
-        if (thermalManager.degTargetHotend(e) && abs(thermalManager.degHotend(e) - thermalManager.degTargetHotend(e)) > 3) {
+        if (thermalManager.degTargetHotend(e) && abs(thermalManager.degHotend(e) - thermalManager.degTargetHotend(e)) > TEMP_HYSTERESIS) {
           heaters_heating = true;
           #if ENABLED(ULTIPANEL)
             lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT);
@@ -5882,7 +5882,7 @@ inline void gcode_M17() {
   ) {
     if (move_away_flag) return false; // already paused
 
-    if (!DEBUGGING(DRYRUN) && unload_length != 0) {
+    if (!DEBUGGING(DRYRUN) && (unload_length != 0 || retract != 0)) {
       #if ENABLED(PREVENT_COLD_EXTRUSION)
         if (!thermalManager.allow_cold_extrude &&
             thermalManager.degTargetHotend(active_extruder) < thermalManager.extrude_min_temp) {
@@ -5919,10 +5919,11 @@ inline void gcode_M17() {
     COPY(resume_position, current_position);
     set_destination_to_current();
 
+    if (retract) {
       // Initial retract before move to filament change position
       destination[E_AXIS] += retract;
-
       RUNPLAN(PAUSE_PARK_RETRACT_FEEDRATE);
+    }
 
     // Lift Z axis
     if (z_lift > 0) {
@@ -5951,6 +5952,7 @@ inline void gcode_M17() {
       destination[E_AXIS] += unload_length;
       RUNPLAN(FILAMENT_CHANGE_UNLOAD_FEEDRATE);
       stepper.synchronize();
+    }
 
     if (show_lcd) {
       #if ENABLED(ULTIPANEL)
@@ -5963,11 +5965,12 @@ inline void gcode_M17() {
     #endif
 
     idle();
-    }
 
-    // Disable extruders steppers for manual filament changing
+    // Disable extruders steppers for manual filament changing (only on boards that have separate ENABLE_PINS)
+    #if E0_ENABLE_PIN != X_ENABLE_PIN && E1_ENABLE_PIN != Y_ENABLE_PIN
       disable_e_steppers();
       safe_delay(100);
+    #endif
 
     // Start the heater idle timers
     const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
@@ -5989,15 +5992,44 @@ inline void gcode_M17() {
         filament_change_beep(max_beep_count);
       #endif
 
+      // If the nozzle has timed out, wait for the user to press the button to re-heat the nozzle, then
+      // re-heat the nozzle, re-show the insert screen, restart the idle timers, and start over
       if (!nozzle_timed_out)
         HOTEND_LOOP()
           nozzle_timed_out |= thermalManager.is_heater_idle(e);
 
+      if (nozzle_timed_out) {
         #if ENABLED(ULTIPANEL)
-        if (nozzle_timed_out)
           lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_CLICK_TO_HEAT_NOZZLE);
         #endif
 
+        // Wait for LCD click or M108
+        while (wait_for_user) idle(true);
+
+        // Re-enable the heaters if they timed out
+        HOTEND_LOOP() thermalManager.reset_heater_idle_timer(e);
+
+        // Wait for the heaters to reach the target temperatures
+        ensure_safe_temperature();
+
+        #if ENABLED(ULTIPANEL)
+          lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_INSERT);
+        #endif
+
+        // Start the heater idle timers
+        const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
+
+        HOTEND_LOOP()
+          thermalManager.start_heater_idle_timer(e, nozzle_timeout);
+
+        wait_for_user = true; /* Wait for user to load filament */
+        nozzle_timed_out = false;
+
+        #if HAS_BUZZER
+          filament_change_beep(max_beep_count, true);
+        #endif
+      }
+
       idle(true);
     }
     KEEPALIVE_STATE(IN_HANDLER);
@@ -6049,7 +6081,7 @@ inline void gcode_M17() {
       stepper.synchronize();
     }
 
-    #if ENABLED(ULTIPANEL) && defined(ADVANCED_PAUSE_EXTRUDE_LENGTH) && ADVANCED_PAUSE_EXTRUDE_LENGTH > 0
+    #if ENABLED(ULTIPANEL) && ADVANCED_PAUSE_EXTRUDE_LENGTH > 0
 
       float extrude_length = initial_extrude_length;
 
@@ -6104,8 +6136,6 @@ inline void gcode_M17() {
       filament_ran_out = false;
     #endif
 
-    set_current_to_destination();
-
     #if ENABLED(ULTIPANEL)
       // Show status screen
       lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_STATUS);
@@ -7643,7 +7673,7 @@ inline void gcode_M18_M84() {
       if (parser.seen('X')) disable_X();
       if (parser.seen('Y')) disable_Y();
       if (parser.seen('Z')) disable_Z();
-      #if ((E0_ENABLE_PIN != X_ENABLE_PIN) && (E1_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS
+      #if E0_ENABLE_PIN != X_ENABLE_PIN && E1_ENABLE_PIN != Y_ENABLE_PIN // Only enable on boards that have separate ENABLE_PINS
         if (parser.seen('E')) disable_e_steppers();
       #endif
     }

Marlin/mesh_bed_leveling.h

@@ -94,8 +94,8 @@
     }
 
     static float calc_z0(const float &a0, const float &a1, const float &z1, const float &a2, const float &z2) {
-      const float delta_z = (z2 - z1) / (a2 - a1);
+      const float delta_z = (z2 - z1) / (a2 - a1),
-      const float delta_a = a0 - a1;
+                  delta_a = a0 - a1;
       return z1 + delta_a * delta_z;
     }
 

Marlin/planner.cpp

@@ -534,7 +534,7 @@ void Planner::check_axes_activity() {
       if (!ubl.state.active) return;
       #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
         // if z_fade_height enabled (nonzero) and raw_z above it, no leveling required
-        if ((planner.z_fade_height) && (planner.z_fade_height <= RAW_Z_POSITION(lz))) return;
+        if (planner.z_fade_height && planner.z_fade_height <= RAW_Z_POSITION(lz)) return;
         lz += ubl.state.z_offset + ubl.get_z_correction(lx, ly) * ubl.fade_scaling_factor_for_z(lz);
       #else // no fade
         lz += ubl.state.z_offset + ubl.get_z_correction(lx, ly);
@@ -598,9 +598,9 @@ void Planner::check_axes_activity() {
 
       if (ubl.state.active) {
 
-        const float z_physical = RAW_Z_POSITION(logical[Z_AXIS]);
+        const float z_physical = RAW_Z_POSITION(logical[Z_AXIS]),
-        const float z_ublmesh  = ubl.get_z_correction(logical[X_AXIS], logical[Y_AXIS]);
+                    z_correct = ubl.get_z_correction(logical[X_AXIS], logical[Y_AXIS]),
-        const float z_virtual  = z_physical - ubl.state.z_offset - z_ublmesh;
+                    z_virtual = z_physical - ubl.state.z_offset - z_correct;
               float z_logical = LOGICAL_Z_POSITION(z_virtual);
 
         #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
@@ -614,10 +614,10 @@ void Planner::check_axes_activity() {
           //    so L=(P-O-M)/(1-M/H) for L<H
 
           if (planner.z_fade_height) {
-            if (z_logical < planner.z_fade_height )
-              z_logical = z_logical / (1.0 - (z_ublmesh * planner.inverse_z_fade_height));
             if (z_logical >= planner.z_fade_height)
               z_logical = LOGICAL_Z_POSITION(z_physical - ubl.state.z_offset);
+            else
+              z_logical /= 1.0 - z_correct * planner.inverse_z_fade_height;
           }
 
         #endif // ENABLE_LEVELING_FADE_HEIGHT

Marlin/ultralcd.cpp

@@ -1019,7 +1019,7 @@ void kill_screen(const char* lcd_msg) {
   #if ENABLED(AUTO_BED_LEVELING_UBL)
 
     float mesh_edit_value, mesh_edit_accumulator; // We round mesh_edit_value to 2.5 decimal places. So we keep a
-                                                  // seperate value that doesn't lose precision.
+                                                  // separate value that doesn't lose precision.
     static int ubl_encoderPosition = 0;
 
     static void _lcd_mesh_fine_tune(const char* msg) {
@@ -1107,11 +1107,16 @@ void kill_screen(const char* lcd_msg) {
   #if ENABLED(ADVANCED_PAUSE_FEATURE)
 
     void lcd_enqueue_filament_change() {
-      if (!DEBUGGING(DRYRUN) && thermalManager.tooColdToExtrude(active_extruder)) {
+
+      #if ENABLED(PREVENT_COLD_EXTRUSION)
+        if (!DEBUGGING(DRYRUN) && !thermalManager.allow_cold_extrude &&
+            thermalManager.degTargetHotend(active_extruder) < thermalManager.extrude_min_temp) {
           lcd_save_previous_screen();
           lcd_goto_screen(lcd_advanced_pause_toocold_menu);
           return;
         }
+      #endif
+
       lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_INIT);
       enqueue_and_echo_commands_P(PSTR("M600 B0"));
     }