Improved the LCD and SD comments blocks in Configuration.h

This commit is contained in:
João Brázio 2016-04-14 20:09:27 +01:00 committed by Scott Lahteine
parent 0fc84b75f4
commit 36a49eab1c

View File

@ -714,7 +714,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section extras // @section extras
//
// EEPROM // EEPROM
//
// The microcontroller can store settings in the EEPROM, e.g. max velocity... // The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM // M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
@ -754,113 +756,250 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define ABS_PREHEAT_HPB_TEMP 110 #define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 #define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
//==============================LCD and SD support============================= //=============================================================================
//============================= LCD and SD support ============================
//=============================================================================
// @section lcd // @section lcd
// Define your display language below. Replace (en) with your language code and uncomment. //
// en, pl, fr, de, es, ru, bg, it, pt, pt_utf8, pt-br, pt-br_utf8, fi, an, nl, ca, eu, kana, kana_utf8, cn, cz, test // MARLIN LANGUAGE
// See also language.h //
// Here you may choose the language used by Marlin on the LCD menus, the following
// list of languages are available:
// en, pl, fr, de, es, ru, bg, it, pt, pt_utf8, pt-br, pt-br_utf8,
// fi, an, nl, ca, eu, kana, kana_utf8, cn, cz, test
//
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. //
// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. // LCD CHARSET
//
// Choose ONE of the following charset list, keep in mind that this selection is
// dependent on your physical hardware thus it has to match the type of Character
// based LCD you have.
//
// Note: This options is ignored for a full graphic display.
//
// To find out what type you have:
// - Compile and upload with language set to 'test'
// - Click to get the menu
//
// You'll see two typical lines from the upper half of the charset.
//
// See also https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language // See also https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
//
#define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware
//#define DISPLAY_CHARSET_HD44780_WESTERN //#define DISPLAY_CHARSET_HD44780_WESTERN
//#define DISPLAY_CHARSET_HD44780_CYRILLIC //#define DISPLAY_CHARSET_HD44780_CYRILLIC
//#define ULTRA_LCD //general LCD support, also 16x2 //
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) // LCD TYPE
//#define SDSUPPORT // Enable SD Card Support in Hardware Console //
// Changed behaviour! If you need SDSUPPORT uncomment it! // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication // (ST7565R family).
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking // IMPORTANT NOTE: You have to install Arduino's U8glib library for the Full
//#define REVERSE_MENU_DIRECTION // When enabled CLOCKWISE moves UP in the LCD menu // Graphics Display to work ! - https://github.com/olikraus/U8glib_Arduino
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. //
//#define ULTIPANEL //the UltiPanel as on Thingiverse //#define ULTRA_LCD // Character based
//#define SPEAKER // The sound device is a speaker - not a buzzer. A buzzer resonates with a fixed frequency. //#define DOGLCD // Full graphics display
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms> // SD CARD
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) //
// http://reprap.org/wiki/PanelOne // SD card support is now disabled by default, if you have [and want] SD support
// then you must uncomment the following directive.
//
//#define SDSUPPORT
//
// SD CARD: SPI SPEED
//
// You may uncomment *one* of the following directives to use slower SPI transfer
// speeds, this is usually required if you're getting volume init errors.
//
//#define SPI_SPEED SPI_HALF_SPEED
//#define SPI_SPEED SPI_QUARTER_SPEED
//#define SPI_SPEED SPI_EIGHTH_SPEED
//
// SD CARD: ENABLE CRC
//
// Use CRC checks and retries on the SD communication.
//
//#define SD_CHECK_AND_RETRY
//
// ENCODER SETTINGS
//
// This option defines how many pulses a encoder should produce for a menu
// step to be produced, you should increase this value for highres encoders.
//
//#define ENCODER_PULSES_PER_STEP 1
//
//
// This option defines how many steps are required for Marlin to move between
// next/prev menu items.
//
//#define ENCODER_STEPS_PER_MENU_ITEM 5
//
//
// This option allows you to reverse the direction you have to turn the encoder
// to navigate up/down on the menus, by default CLOCKWISE rotation moves DOWN in
// the LCD menu, when active CLOCKWISE rotation will move UP in the LCD menu.
//
//#define REVERSE_MENU_DIRECTION
//
//
// If you have a speaker activate this directive to enable it.
// By default Marlin assumes your setup is buzzer based and no action is required.
//
//#define SPEAKER
//
// The duration and frequency the buzzer plays the UI feedback sound.
// You may define these directives with 0 (zero) if you want to disable all sound
// feedback from Marlin.
//
// Note: You may test the buzzing sound with the G-Code:
// M300 S<frequency Hz> P<duration ms>
//
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
//
// CONTROLLER TYPE: Standard
//
// Marlin supports a impressive variety of controllers, uncomment the directive
// which defines physical controller you're using.
//
//
// Activate this directive if you have an ULTIMAKER Controller.
//
//#define ULTIMAKERCONTROLLER
//
//
// Activate this directive if you have a ULTIPANEL as seen on Thingiverse.
//
//#define ULTIPANEL
//
//
// Activate this directive if you have a PanelOne from T3P3
// (via RAMPS 1.4 AUX2/AUX3) - http://reprap.org/wiki/PanelOne
//
//#define PANEL_ONE //#define PANEL_ONE
//
// The MaKr3d Makr-Panel with graphic controller and SD support //
// http://reprap.org/wiki/MaKr3d_MaKrPanel // Activate this directive if you have a MaKr3d Makr-Panel with graphic
// controller and SD suppord - http://reprap.org/wiki/MaKr3d_MaKrPanel
//
//#define MAKRPANEL //#define MAKRPANEL
//
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD //
// http://panucatt.com // Activate one of these directives if you have a Panucatt Devices Viki 2.0 or
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino // mini Viki with Graphic LCD - http://panucatt.com
//
//#define VIKI2 //#define VIKI2
//#define miniVIKI //#define miniVIKI
// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
// //
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino //
// Activate this directive if you have an Adafruit ST7565 Full Graphic Controller.
// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
//
//#define ELB_FULL_GRAPHIC_CONTROLLER //#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SD_DETECT_INVERTED //
//
// The RepRapDiscount Smart Controller (white PCB) // Activate this directive if you have a RepRapDiscount Smart Controller.
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
//
// Note: Usually sold in a white PCB.
//
//#define REPRAP_DISCOUNT_SMART_CONTROLLER //#define REPRAP_DISCOUNT_SMART_CONTROLLER
//
// The GADGETS3D G3D LCD/SD Controller (blue PCB) //
// Activate this directive if you have a BQ LCD Smart Controller shipped by
// default with the BQ Hephestos 2 and Witbox 2.
//
//#define BQ_LCD_SMART_CONTROLLER
//
//
// Activate this directive if you have a GADGETS3D G3D LCD/SD Controller
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
//
// Note: Usually sold in a blue PCB.
//
//#define G3D_PANEL //#define G3D_PANEL
//
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) //
// Activate this directive if you have a RepRapDiscount FULL GRAPHIC Smart Controller
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
// //
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
// #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER // #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
//#define REPRAPWORLD_KEYPAD
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
// The Elefu RA Board Control Panel
// http://www.elefu.com/index.php?route=product/product&product_id=53
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
//#define RA_CONTROL_PANEL
// The MakerLab Mini Panel with graphic controller and SD support
// http://reprap.org/wiki/Mini_panel
//#define MINIPANEL
/**
* I2C Panels
*/
//#define LCD_I2C_SAINSMART_YWROBOT
//#define LCM1602 // LCM1602 Adapter for 16x2 LCD
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
// //
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) //
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. // Activate this directive if you have a MakerLab Mini Panel with graphic
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) // controller and SD support - http://reprap.org/wiki/Mini_panel
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin //#define MINIPANEL
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). //
//
// Activate this directive if you have a RepRapWorld REPRAPWORLD_KEYPAD v1.1
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
//
// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
// is pressed, a value of 10.0 means 10mm per click.
//
//#define REPRAPWORLD_KEYPAD
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
//
// CONTROLLER TYPE: I2C
//
// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
//
//
// Activate this directive if you have an Elefu RA Board Control Panel
// http://www.elefu.com/index.php?route=product/product&product_id=53
//
//#define RA_CONTROL_PANEL
//#define LCD_I2C_SAINSMART_YWROBOT
//
//
// Activate this directive if you have a LCM160 LCD adapter.
//
//#define LCM1602
//
//
// Activate this directive if you have a PANELOLU2 LCD with status LEDs,
// separate encoder and click inputs.
//
// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
// For more info: https://github.com/lincomatic/LiquidTWI2
//
// Note: The PANELOLU2 encoder click input can either be directly connected to
// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
//
//#define LCD_I2C_PANELOLU2 //#define LCD_I2C_PANELOLU2
//
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //
// Activate this directive if you have a Panucatt VIKI LCD with status LEDs,
// integrated click & L/R/U/D buttons, separate encoder inputs.
//
//#define LCD_I2C_VIKI //#define LCD_I2C_VIKI
//
// SSD1306 OLED generic display support //
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino // Activate this directive if you have a SSD1306 OLED full graphics generic display
//
//#define U8GLIB_SSD1306 //#define U8GLIB_SSD1306
// Shift register panels //
// --------------------- // CONTROLLER TYPE: Shift register panels
// 2 wire Non-latching LCD SR from: //
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
//
//#define SAV_3DLCD //#define SAV_3DLCD
// @section extras // @section extras