Merge pull request #1944 from AnHardt/beep2

More Beeper clean up

Marlin/Configuration.h

@@ -661,10 +661,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
-
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //#define PANEL_ONE
@@ -792,13 +791,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 // Uncomment below to enable
 //#define FILAMENT_SENSOR
 
-#define FILAMENT_SENSOR_EXTRUDER_NUM	0  //The number of the extruder that has the filament sensor (0,1,2)
+#define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
-#define MEASUREMENT_DELAY_CM			14  //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+#define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA  3.0  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
-#define MEASURED_UPPER_LIMIT          3.30  //upper limit factor used for sensor reading validation in mm
+#define MEASURED_UPPER_LIMIT         3.3 //upper limit factor used for sensor reading validation in mm
-#define MEASURED_LOWER_LIMIT          1.90  //lower limit factor for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT         1.9 //lower limit factor for sensor reading validation in mm
-#define MAX_MEASUREMENT_DELAY			20  //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+#define MAX_MEASUREMENT_DELAY       20   //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
 
 //defines used in the code
 #define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially

Marlin/Marlin_main.cpp

@@ -4022,20 +4022,8 @@ inline void gcode_M226() {
   inline void gcode_M300() {
     uint16_t beepS = code_seen('S') ? code_value_short() : 110;
     uint32_t beepP = code_seen('P') ? code_value_long() : 1000;
-    if (beepS > 0) {
+    if (beepP > 5000) beepP = 5000; // limit to 5 seconds
-      #if BEEPER > 0
+    lcd_buzz(beepP, beepS);
-        tone(BEEPER, beepS);
-        delay(beepP);
-        noTone(BEEPER);
-      #elif defined(ULTRALCD)
-        lcd_buzz(beepS, beepP);
-      #elif defined(LCD_USE_I2C_BUZZER)
-        lcd_buzz(beepP, beepS);
-      #endif
-    }
-    else {
-      delay(beepP);
-    }
   }
 
 #endif // BEEPER>0 || ULTRALCD || LCD_USE_I2C_BUZZER

Marlin/configurator/config/Configuration.h

@@ -660,9 +660,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/Felix/Configuration.h

@@ -594,9 +594,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -590,9 +590,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/Hephestos/Configuration.h

@@ -614,9 +614,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/K8200/Configuration.h

@@ -672,9 +672,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 #define ULTIMAKERCONTROLLER // K8200: for Display VM8201 // as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/SCARA/Configuration.h

@@ -645,9 +645,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/WITBOX/Configuration.h

@@ -613,9 +613,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/delta/generic/Configuration.h

@@ -662,9 +662,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -666,9 +666,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/makibox/Configuration.h

@@ -613,9 +613,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -619,9 +619,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
-                                               // 0 to disable buzzer feedback  
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
+                                                 // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne

Marlin/ultralcd.cpp

@@ -1131,23 +1131,18 @@ void lcd_quick_feedback() {
     #endif    
     lcd_buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
   #elif defined(BEEPER) && BEEPER > -1
-    SET_OUTPUT(BEEPER);
     #ifndef LCD_FEEDBACK_FREQUENCY_HZ
       #define LCD_FEEDBACK_FREQUENCY_HZ 5000
     #endif
     #ifndef LCD_FEEDBACK_FREQUENCY_DURATION_MS
       #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
     #endif
-    const uint16_t delay = 1000000 / LCD_FEEDBACK_FREQUENCY_HZ / 2;
+    lcd_buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
-    uint16_t i = LCD_FEEDBACK_FREQUENCY_DURATION_MS * LCD_FEEDBACK_FREQUENCY_HZ / 1000;
+  #else
-    while (i--) {
+    #ifndef LCD_FEEDBACK_FREQUENCY_DURATION_MS
-      WRITE(BEEPER,HIGH);
+      #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
-      delayMicroseconds(delay);
+    #endif
-      WRITE(BEEPER,LOW);
+    delay(LCD_FEEDBACK_FREQUENCY_DURATION_MS);
-      delayMicroseconds(delay);
-    }
-    const uint16_t j = max(10000 - LCD_FEEDBACK_FREQUENCY_DURATION_MS * 1000, 0);
-    if (j) delayMicroseconds(j);
   #endif
 }
 
@@ -1544,9 +1539,19 @@ bool lcd_detected(void) {
 }
 
 void lcd_buzz(long duration, uint16_t freq) {
-  #ifdef LCD_USE_I2C_BUZZER
+  if (freq > 0) {
-    lcd.buzz(duration,freq);
+    #if BEEPER > 0
-  #endif
+      SET_OUTPUT(BEEPER);
+      tone(BEEPER, freq, duration);
+    #elif defined(LCD_USE_I2C_BUZZER)
+      lcd.buzz(duration,freq);
+    #else
+      delay(duration);
+    #endif
+  }
+  else {
+    delay(duration);
+  }
 }
 
 bool lcd_clicked() { return LCD_CLICKED; }