Merge pull request #780 from Cylindric3D/typofixes_2

Various typo fixes #2 - only in comments, no code changes.
This commit is contained in:
nothinman 2014-02-17 11:29:18 +00:00
commit 4ddedb3b27
5 changed files with 16 additions and 16 deletions

View File

@ -11,7 +11,7 @@
#include "WProgram.h"
#endif
// it is a russian alphabet translation
// it is a Russian alphabet translation
// except 0401 --> 0xa2 = ╗, 0451 --> 0xb5
const PROGMEM uint8_t utf_recode[] =
{ 0x41,0xa0,0x42,0xa1,0xe0,0x45,0xa3,0xa4,0xa5,0xa6,0x4b,0xa7,0x4d,0x48,0x4f,
@ -115,7 +115,7 @@ void LiquidCrystalRus::begin(uint8_t cols, uint8_t lines, uint8_t dotsize) {
// SEE PAGE 45/46 FOR INITIALIZATION SPECIFICATION!
// according to datasheet, we need at least 40ms after power rises above 2.7V
// before sending commands. Arduino can turn on way befer 4.5V so we'll wait 50
// before sending commands. Arduino can turn on way before 4.5V so we'll wait 50
delayMicroseconds(50000);
// Now we pull both RS and R/W low to begin commands
digitalWrite(_rs_pin, LOW);
@ -126,7 +126,7 @@ void LiquidCrystalRus::begin(uint8_t cols, uint8_t lines, uint8_t dotsize) {
//put the LCD into 4 bit or 8 bit mode
if (! (_displayfunction & LCD_8BITMODE)) {
// this is according to the hitachi HD44780 datasheet
// this is according to the Hitachi HD44780 datasheet
// figure 24, pg 46
// we start in 8bit mode, try to set 4 bit mode
@ -144,7 +144,7 @@ void LiquidCrystalRus::begin(uint8_t cols, uint8_t lines, uint8_t dotsize) {
// finally, set to 8-bit interface
writeNbits(0x02,4);
} else {
// this is according to the hitachi HD44780 datasheet
// this is according to the Hitachi HD44780 datasheet
// page 45 figure 23
// Send function set command sequence
@ -308,7 +308,7 @@ inline void LiquidCrystalRus::command(uint8_t value) {
}
} else send(out_char, HIGH);
#if defined(ARDUINO) && ARDUINO >= 100
return 1; // assume sucess
return 1; // assume success
#endif
}

View File

@ -25,7 +25,7 @@
#ifndef AT90USB
// this next line disables the entire HardwareSerial.cpp,
// this is so I can support Attiny series and any other chip without a uart
// this is so I can support Attiny series and any other chip without a UART
#if defined(UBRRH) || defined(UBRR0H) || defined(UBRR1H) || defined(UBRR2H) || defined(UBRR3H)
#if UART_PRESENT(SERIAL_PORT)
@ -73,7 +73,7 @@ void MarlinSerial::begin(long baud)
bool useU2X = true;
#if F_CPU == 16000000UL && SERIAL_PORT == 0
// hardcoded exception for compatibility with the bootloader shipped
// hard coded exception for compatibility with the bootloader shipped
// with the Duemilanove and previous boards and the firmware on the 8U2
// on the Uno and Mega 2560.
if (baud == 57600) {

View File

@ -22,7 +22,7 @@ CardReader::CardReader()
file_subcall_ctr=0;
memset(workDirParents, 0, sizeof(workDirParents));
autostart_stilltocheck=true; //the sd start is delayed, because otherwise the serial cannot answer fast enought to make contact with the hostsoftware.
autostart_stilltocheck=true; //the SD start is delayed, because otherwise the serial cannot answer fast enough to make contact with the host software.
lastnr=0;
//power to SD reader
#if SDPOWER > -1
@ -245,7 +245,7 @@ void CardReader::openFile(char* name,bool read, bool replace_current/*=true*/)
{
if(!cardOK)
return;
if(file.isOpen()) //replaceing current file by new file, or subfile call
if(file.isOpen()) //replacing current file by new file, or subfile call
{
if(!replace_current)
{
@ -544,7 +544,7 @@ void CardReader::closefile(bool store_location)
if(store_location)
{
//future: store printer state, filename and position for continueing a stoped print
//future: store printer state, filename and position for continuing a stopped print
// so one can unplug the printer and continue printing the next day.
}

View File

@ -12,8 +12,8 @@
#define ST7920_DAT_PIN LCD_PINS_ENABLE
#define ST7920_CS_PIN LCD_PINS_RS
//#define PAGE_HEIGHT 8 //128 byte frambuffer
//#define PAGE_HEIGHT 16 //256 byte frambuffer
//#define PAGE_HEIGHT 8 //128 byte framebuffer
//#define PAGE_HEIGHT 16 //256 byte framebuffer
#define PAGE_HEIGHT 32 //512 byte framebuffer
#define WIDTH 128
@ -59,8 +59,8 @@ uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, vo
ST7920_SET_CMD();
ST7920_WRITE_BYTE(0x08); //display off, cursor+blink off
ST7920_WRITE_BYTE(0x01); //clear CGRAM ram
u8g_Delay(10); //delay for cgram clear
ST7920_WRITE_BYTE(0x3E); //extended mode + gdram active
u8g_Delay(10); //delay for CGRAM clear
ST7920_WRITE_BYTE(0x3E); //extended mode + GDRAM active
for(y=0;y<HEIGHT/2;y++) //clear GDRAM
{
ST7920_WRITE_BYTE(0x80|y); //set y

View File

@ -4,9 +4,9 @@
#include "Marlin.h"
#ifdef USE_WATCHDOG
// intialise watch dog with a 1 sec interrupt time
// initialize watch dog with a 1 sec interrupt time
void watchdog_init();
// pad the dog/reset watchdog. MUST be called at least every second after the first watchdog_init or avr will go into emergency procedures..
// pad the dog/reset watchdog. MUST be called at least every second after the first watchdog_init or AVR will go into emergency procedures..
void watchdog_reset();
#else
//If we do not have a watchdog, then we can have empty functions which are optimized away.