Fix Endstops Core compatibility (#10822)

Co-Authored-By: ejtagle <ejtagle@hotmail.com>

Marlin/endstops.cpp

@@ -36,9 +36,9 @@
 #endif
 
 #if HAS_BED_PROBE
-  #define ENDSTOPS_ENABLED  (endstops.enabled || endstops.z_probe_enabled)
+  #define ENDSTOPS_ENABLED  (enabled || z_probe_enabled)
 #else
-  #define ENDSTOPS_ENABLED  endstops.enabled
+  #define ENDSTOPS_ENABLED  enabled
 #endif
 
 Endstops endstops;
@@ -196,17 +196,17 @@ void Endstops::init() {
 } // Endstops::init
 
 // Called from ISR. A change was detected. Find out what happened!
-void Endstops::check_possible_change() { if (ENDSTOPS_ENABLED) endstops.update(); }
+void Endstops::check_possible_change() { if (ENDSTOPS_ENABLED) update(); }
 
 // Called from ISR: Poll endstop state if required
 void Endstops::poll() {
 
   #if ENABLED(PINS_DEBUGGING)
-    endstops.run_monitor();  // report changes in endstop status
+    run_monitor();  // report changes in endstop status
   #endif
 
   #if DISABLED(ENDSTOP_INTERRUPTS_FEATURE) || ENABLED(ENDSTOP_NOISE_FILTER)
-    if (ENDSTOPS_ENABLED) endstops.update();
+    if (ENDSTOPS_ENABLED) update();
   #endif
 }
 
@@ -214,7 +214,7 @@ void Endstops::enable_globally(const bool onoff) {
   enabled_globally = enabled = onoff;
 
   #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-    if (onoff) endstops.update(); // If enabling, update state now
+    if (onoff) update(); // If enabling, update state now
   #endif
 }
 
@@ -223,17 +223,16 @@ void Endstops::enable(const bool onoff) {
   enabled = onoff;
 
   #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-    if (onoff) endstops.update(); // If enabling, update state now
+    if (onoff) update(); // If enabling, update state now
   #endif
 }
 
-
 // Disable / Enable endstops based on ENSTOPS_ONLY_FOR_HOMING and global enable
 void Endstops::not_homing() {
   enabled = enabled_globally;
 
   #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-    if (enabled) endstops.update(); // If enabling, update state now
+    if (enabled) update(); // If enabling, update state now
   #endif
 }
 
@@ -242,7 +241,7 @@ void Endstops::hit_on_purpose() {
   hit_state = 0;
 
   #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-    if (enabled) endstops.update(); // If enabling, update state now
+    if (enabled) update(); // If enabling, update state now
   #endif
 }
 
@@ -252,7 +251,7 @@ void Endstops::hit_on_purpose() {
     z_probe_enabled = onoff;
 
     #if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-      if (enabled) endstops.update(); // If enabling, update state now
+      if (enabled) update(); // If enabling, update state now
     #endif
   }
 #endif
@@ -379,7 +378,6 @@ void Endstops::M119() {
 // Check endstops - Could be called from ISR!
 void Endstops::update() {
 
-  #define SET_BIT(N,B,TF) do{ if (TF) SBI(N,B); else CBI(N,B); }while(0)
   // UPDATE_ENDSTOP_BIT: set the current endstop bits for an endstop to its status
   #define UPDATE_ENDSTOP_BIT(AXIS, MINMAX) SET_BIT(live_state, _ENDSTOP(AXIS, MINMAX), (READ(_ENDSTOP_PIN(AXIS, MINMAX)) != _ENDSTOP_INVERTING(AXIS, MINMAX)))
   // COPY_BIT: copy the value of SRC_BIT to DST_BIT in DST
@@ -390,75 +388,6 @@ void Endstops::update() {
     if (G38_move) UPDATE_ENDSTOP_BIT(Z, MIN_PROBE);
   #endif
 
-  /**
-   * Define conditions for checking endstops
-   */
-
-  #if IS_CORE
-    #define S_(N) stepper.movement_non_null(CORE_AXIS_##N)
-    #define D_(N) stepper.motor_direction(CORE_AXIS_##N)
-  #endif
-
-  #if CORE_IS_XY || CORE_IS_XZ
-    /**
-     * Head direction in -X axis for CoreXY and CoreXZ bots.
-     *
-     * If steps differ, both axes are moving.
-     * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Y or Z, handled below)
-     * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X)
-     */
-    #if ENABLED(COREXY) || ENABLED(COREXZ)
-      #define X_CMP ==
-    #else
-      #define X_CMP !=
-    #endif
-    #define X_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) X_CMP D_(2)) )
-    #define X_AXIS_HEAD X_HEAD
-  #else
-    #define X_MOVE_TEST stepper.movement_non_null(X_AXIS)
-    #define X_AXIS_HEAD X_AXIS
-  #endif
-
-  #if CORE_IS_XY || CORE_IS_YZ
-    /**
-     * Head direction in -Y axis for CoreXY / CoreYZ bots.
-     *
-     * If steps differ, both axes are moving
-     * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X or Y)
-     * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Y or Z)
-     */
-    #if ENABLED(COREYX) || ENABLED(COREYZ)
-      #define Y_CMP ==
-    #else
-      #define Y_CMP !=
-    #endif
-    #define Y_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) Y_CMP D_(2)) )
-    #define Y_AXIS_HEAD Y_HEAD
-  #else
-    #define Y_MOVE_TEST stepper.movement_non_null(Y_AXIS)
-    #define Y_AXIS_HEAD Y_AXIS
-  #endif
-
-  #if CORE_IS_XZ || CORE_IS_YZ
-    /**
-     * Head direction in -Z axis for CoreXZ or CoreYZ bots.
-     *
-     * If steps differ, both axes are moving
-     * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X or Y, already handled above)
-     * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Z)
-     */
-    #if ENABLED(COREZX) || ENABLED(COREZY)
-      #define Z_CMP ==
-    #else
-      #define Z_CMP !=
-    #endif
-    #define Z_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) Z_CMP D_(2)) )
-    #define Z_AXIS_HEAD Z_HEAD
-  #else
-    #define Z_MOVE_TEST stepper.movement_non_null(Z_AXIS)
-    #define Z_AXIS_HEAD Z_AXIS
-  #endif
-
   // With Dual X, endstops are only checked in the homing direction for the active extruder
   #if ENABLED(DUAL_X_CARRIAGE)
     #define E0_ACTIVE stepper.movement_extruder() == 0
@@ -469,10 +398,27 @@ void Endstops::update() {
     #define X_MAX_TEST true
   #endif
 
+  // Use HEAD for core axes, AXIS for others
+  #if CORE_IS_XY || CORE_IS_XZ
+    #define X_AXIS_HEAD X_HEAD
+  #else
+    #define X_AXIS_HEAD X_AXIS
+  #endif
+  #if CORE_IS_XY || CORE_IS_YZ
+    #define Y_AXIS_HEAD Y_HEAD
+  #else
+    #define Y_AXIS_HEAD Y_AXIS
+  #endif
+  #if CORE_IS_XZ || CORE_IS_YZ
+    #define Z_AXIS_HEAD Z_HEAD
+  #else
+    #define Z_AXIS_HEAD Z_AXIS
+  #endif
+
   /**
    * Check and update endstops according to conditions
    */
-  if (X_MOVE_TEST) {
+  if (stepper.axis_is_moving(X_AXIS)) {
     if (stepper.motor_direction(X_AXIS_HEAD)) { // -direction
       #if HAS_X_MIN
         #if ENABLED(X_DUAL_ENDSTOPS)
@@ -503,7 +449,7 @@ void Endstops::update() {
     }
   }
 
-  if (Y_MOVE_TEST) {
+  if (stepper.axis_is_moving(Y_AXIS)) {
     if (stepper.motor_direction(Y_AXIS_HEAD)) { // -direction
       #if HAS_Y_MIN
         #if ENABLED(Y_DUAL_ENDSTOPS)
@@ -534,7 +480,7 @@ void Endstops::update() {
     }
   }
 
-  if (Z_MOVE_TEST) {
+  if (stepper.axis_is_moving(Z_AXIS)) {
     if (stepper.motor_direction(Z_AXIS_HEAD)) { // Z -direction. Gantry down, bed up.
       #if HAS_Z_MIN
         #if ENABLED(Z_DUAL_ENDSTOPS)
@@ -555,9 +501,7 @@ void Endstops::update() {
 
       // When closing the gap check the enabled probe
       #if ENABLED(Z_MIN_PROBE_ENDSTOP)
-        if (z_probe_enabled) {
+        if (z_probe_enabled) UPDATE_ENDSTOP_BIT(Z, MIN_PROBE);
-          UPDATE_ENDSTOP_BIT(Z, MIN_PROBE);
-        }
       #endif
     }
     else { // Z +direction. Gantry up, bed down.
@@ -633,16 +577,16 @@ void Endstops::update() {
     // If G38 command is active check Z_MIN_PROBE for ALL movement
     if (G38_move) {
       if (TEST_ENDSTOP(_ENDSTOP(Z, MIN_PROBE))) {
-        if      (stepper.movement_non_null(_AXIS(X))) { _ENDSTOP_HIT(X, MIN); planner.endstop_triggered(_AXIS(X)); }
+        if      (stepper.axis_is_moving(_AXIS(X))) { _ENDSTOP_HIT(X, MIN); planner.endstop_triggered(_AXIS(X)); }
-        else if (stepper.movement_non_null(_AXIS(Y))) { _ENDSTOP_HIT(Y, MIN); planner.endstop_triggered(_AXIS(Y)); }
+        else if (stepper.axis_is_moving(_AXIS(Y))) { _ENDSTOP_HIT(Y, MIN); planner.endstop_triggered(_AXIS(Y)); }
-        else if (stepper.movement_non_null(_AXIS(Z))) { _ENDSTOP_HIT(Z, MIN); planner.endstop_triggered(_AXIS(Z)); }
+        else if (stepper.axis_is_moving(_AXIS(Z))) { _ENDSTOP_HIT(Z, MIN); planner.endstop_triggered(_AXIS(Z)); }
         G38_endstop_hit = true;
       }
     }
   #endif
 
   // Now, we must signal, after validation, if an endstop limit is pressed or not
-  if (X_MOVE_TEST) {
+  if (stepper.axis_is_moving(X_AXIS)) {
     if (stepper.motor_direction(X_AXIS_HEAD)) { // -direction
       #if HAS_X_MIN
         #if ENABLED(X_DUAL_ENDSTOPS)
@@ -663,7 +607,7 @@ void Endstops::update() {
     }
   }
 
-  if (Y_MOVE_TEST) {
+  if (stepper.axis_is_moving(Y_AXIS)) {
     if (stepper.motor_direction(Y_AXIS_HEAD)) { // -direction
       #if HAS_Y_MIN
         #if ENABLED(Y_DUAL_ENDSTOPS)
@@ -684,7 +628,7 @@ void Endstops::update() {
     }
   }
 
-  if (Z_MOVE_TEST) {
+  if (stepper.axis_is_moving(Z_AXIS)) {
     if (stepper.motor_direction(Z_AXIS_HEAD)) { // Z -direction. Gantry down, bed up.
       #if HAS_Z_MIN
         #if ENABLED(Z_DUAL_ENDSTOPS)

Marlin/macros.h

@@ -70,6 +70,7 @@
 #define TEST(n,b) !!((n)&_BV(b))
 #define SBI(n,b) (n |= _BV(b))
 #define CBI(n,b) (n &= ~_BV(b))
+#define SET_BIT(N,B,TF) do{ if (TF) SBI(N,B); else CBI(N,B); }while(0)
 
 #define _BV32(b) (1UL << (b))
 #define TEST32(n,b) !!((n)&_BV32(b))

Marlin/stepper.cpp

@@ -85,10 +85,10 @@ block_t* Stepper::current_block = NULL;  // A pointer to the block currently bei
 
 // private:
 
-uint8_t Stepper::last_direction_bits = 0,       // The next stepping-bits to be output
+uint8_t Stepper::last_direction_bits = 0,
-        Stepper::last_movement_extruder = 0xFF; // Last movement extruder, as computed when the last movement was fetched from planner
+        Stepper::last_movement_extruder = 0xFF,
-bool Stepper::abort_current_block,              // Signals to the stepper that current block should be aborted
+        Stepper::axis_did_move;
-     Stepper::last_movement_non_null[NUM_AXIS]; // Last Movement in the given direction is not null, as computed when the last movement was fetched from planner
+bool Stepper::abort_current_block;
 
 #if ENABLED(X_DUAL_ENDSTOPS)
   bool Stepper::locked_x_motor = false, Stepper::locked_x2_motor = false;
@@ -367,10 +367,6 @@ void Stepper::set_directions() {
   #endif // !LIN_ADVANCE
 }
 
-#if ENABLED(ENDSTOP_INTERRUPTS_FEATURE)
-  extern volatile uint8_t e_hit;
-#endif
-
 #if ENABLED(BEZIER_JERK_CONTROL)
   /**
    *   We are using a quintic (fifth-degree) Bézier polynomial for the velocity curve.
@@ -1533,8 +1529,75 @@ uint32_t Stepper::stepper_block_phase_isr() {
           return interval; // No more queued movements!
       }
 
-      // Compute movement direction for proper endstop handling
+      // Flag all moving axes for proper endstop handling
-      LOOP_NA(i) last_movement_non_null[i] = !!current_block->steps[i];
+
+      #if IS_CORE
+        // Define conditions for checking endstops
+        #define S_(N) current_block->steps[CORE_AXIS_##N]
+        #define D_(N) motor_direction(CORE_AXIS_##N)
+      #endif
+
+      #if CORE_IS_XY || CORE_IS_XZ
+        /**
+         * Head direction in -X axis for CoreXY and CoreXZ bots.
+         *
+         * If steps differ, both axes are moving.
+         * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Y or Z, handled below)
+         * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X)
+         */
+        #if ENABLED(COREXY) || ENABLED(COREXZ)
+          #define X_CMP ==
+        #else
+          #define X_CMP !=
+        #endif
+        #define X_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) X_CMP D_(2)) )
+      #else
+        #define X_MOVE_TEST !!current_block->steps[X_AXIS]
+      #endif
+
+      #if CORE_IS_XY || CORE_IS_YZ
+        /**
+         * Head direction in -Y axis for CoreXY / CoreYZ bots.
+         *
+         * If steps differ, both axes are moving
+         * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X or Y)
+         * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Y or Z)
+         */
+        #if ENABLED(COREYX) || ENABLED(COREYZ)
+          #define Y_CMP ==
+        #else
+          #define Y_CMP !=
+        #endif
+        #define Y_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) Y_CMP D_(2)) )
+      #else
+        #define Y_MOVE_TEST !!current_block->steps[Y_AXIS]
+      #endif
+
+      #if CORE_IS_XZ || CORE_IS_YZ
+        /**
+         * Head direction in -Z axis for CoreXZ or CoreYZ bots.
+         *
+         * If steps differ, both axes are moving
+         * If DeltaA ==  DeltaB, the movement is only in the 1st axis (X or Y, already handled above)
+         * If DeltaA == -DeltaB, the movement is only in the 2nd axis (Z)
+         */
+        #if ENABLED(COREZX) || ENABLED(COREZY)
+          #define Z_CMP ==
+        #else
+          #define Z_CMP !=
+        #endif
+        #define Z_MOVE_TEST ( S_(1) != S_(2) || (S_(1) > 0 && D_(1) Z_CMP D_(2)) )
+      #else
+        #define Z_MOVE_TEST !!current_block->steps[Z_AXIS]
+      #endif
+
+      SET_BIT(axis_did_move, X_AXIS, X_MOVE_TEST);
+      SET_BIT(axis_did_move, Y_AXIS, Y_MOVE_TEST);
+      SET_BIT(axis_did_move, Z_AXIS, Z_MOVE_TEST);
+      SET_BIT(axis_did_move, E_AXIS, !!current_block->steps[E_AXIS]);
+      SET_BIT(axis_did_move, X_HEAD, !!current_block->steps[X_HEAD]);
+      SET_BIT(axis_did_move, Y_HEAD, !!current_block->steps[Y_HEAD]);
+      SET_BIT(axis_did_move, Z_HEAD, !!current_block->steps[Z_HEAD]);
 
       // Initialize the trapezoid generator from the current block.
       #if ENABLED(LIN_ADVANCE)

Marlin/stepper.h

@@ -99,9 +99,9 @@ class Stepper {
   private:
 
     static uint8_t last_direction_bits,     // The next stepping-bits to be output
-                   last_movement_extruder;        // Last movement extruder, as computed when the last movement was fetched from planner
+                   last_movement_extruder,  // Last movement extruder, as computed when the last movement was fetched from planner
-    static bool abort_current_block,              // Signals to the stepper that current block should be aborted
+                   axis_did_move;           // Last Movement in the given direction is not null, as computed when the last movement was fetched from planner
-                last_movement_non_null[NUM_AXIS]; // Last Movement in the given direction is not null, as computed when the last movement was fetched from planner
+    static bool abort_current_block;        // Signals to the stepper that current block should be aborted
 
     #if ENABLED(X_DUAL_ENDSTOPS)
       static bool locked_x_motor, locked_x2_motor;
@@ -219,7 +219,7 @@ class Stepper {
     FORCE_INLINE static bool motor_direction(const AxisEnum axis) { return TEST(last_direction_bits, axis); }
 
     // The last movement direction was not null on the specified axis. Note that motor direction is not necessarily the same.
-    FORCE_INLINE static bool movement_non_null(const AxisEnum axis) { return last_movement_non_null[axis]; }
+    FORCE_INLINE static bool axis_is_moving(const AxisEnum axis) { return TEST(axis_did_move, axis); }
 
     // The extruder associated to the last movement
     FORCE_INLINE static uint8_t movement_extruder() { return last_movement_extruder; }