Merge pull request #1828 from Wackerbarth/Configurator
Update Configurator Files
This commit is contained in:
Scott Lahteine
commit
6a860b99dc
@ -35,6 +35,8 @@ Here are some standard links for getting your machine calibrated:
|
||||
// example_configurations/SCARA directory.
|
||||
//
|
||||
|
||||
// @section info
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
@ -45,12 +47,16 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1
|
||||
//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2
|
||||
|
||||
// @section machine
|
||||
|
||||
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
||||
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||||
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
// :[0,1,2,3,4,5,6,7]
|
||||
#define SERIAL_PORT 0
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
// :[2400,9600,19200,38400,57600,115200,250000]
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// This enables the serial port associated to the Bluetooth interface
|
||||
@ -70,6 +76,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1,2,3,4]
|
||||
#define EXTRUDERS 1
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
@ -81,12 +88,15 @@ Here are some standard links for getting your machine calibrated:
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
// :{1:'ATX',2:'X-Box 360'}
|
||||
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
@ -248,6 +258,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
// @section extruder
|
||||
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
@ -302,12 +313,16 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// @section machine
|
||||
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// @section homing
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
@ -332,6 +347,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// @section machine
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
@ -339,6 +356,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
#define Z_ENABLE_ON 0
|
||||
@ -348,20 +366,32 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define DISABLE_X false
|
||||
#define DISABLE_Y false
|
||||
#define DISABLE_Z false
|
||||
|
||||
// @section extruder
|
||||
|
||||
#define DISABLE_E false // For all extruders
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
||||
// @section homing
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
@ -369,6 +399,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// @section machine
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 0
|
||||
@ -408,6 +440,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//============================= Bed Auto Leveling ===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section bedlevel
|
||||
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
||||
@ -516,6 +550,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
@ -529,6 +565,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
|
||||
// @section movement
|
||||
|
||||
/**
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
@ -555,6 +593,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// @section more
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
#ifdef CUSTOM_M_CODES
|
||||
@ -565,6 +605,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// EEPROM
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
@ -577,6 +618,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// please keep turned on if you can.
|
||||
//#define EEPROM_CHITCHAT
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 180
|
||||
#define PLA_PREHEAT_HPB_TEMP 70
|
||||
@ -587,6 +630,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
//==============================LCD and SD support=============================
|
||||
// @section lcd
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
|
||||
@ -670,6 +714,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
|
||||
//#define SAV_3DLCD
|
||||
|
||||
// @section extras
|
||||
|
||||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
|
||||
@ -3,6 +3,8 @@
|
||||
|
||||
#include "Conditionals.h"
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
@ -46,6 +48,8 @@
|
||||
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
@ -55,6 +59,8 @@
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
// @section temperature
|
||||
|
||||
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
#define TEMP_SENSOR_AD595_OFFSET 0.0
|
||||
@ -72,6 +78,8 @@
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// @section extruder
|
||||
|
||||
// Extruder cooling fans
|
||||
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
@ -89,8 +97,12 @@
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
// @section extras
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
@ -174,6 +186,8 @@
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
// @section homing
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_BUMP_MM 5
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
@ -181,8 +195,12 @@
|
||||
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
// @section machine
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
// @section machine
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
@ -195,11 +213,15 @@
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// @section lcd
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
@ -241,6 +263,8 @@
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
// @section lcd
|
||||
|
||||
#ifdef SDSUPPORT
|
||||
|
||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
||||
@ -273,6 +297,8 @@
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
// @section more
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
//#define USE_WATCHDOG
|
||||
|
||||
@ -317,6 +343,8 @@
|
||||
|
||||
const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
@ -324,6 +352,8 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
//=============================Buffers ============================
|
||||
//===========================================================================
|
||||
|
||||
// @section hidden
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#ifdef SDSUPPORT
|
||||
@ -332,11 +362,13 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
// @section more
|
||||
|
||||
//The ASCII buffer for receiving from the serial:
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
|
||||
// @section extras
|
||||
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
|
||||
@ -31,7 +31,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// For a Scara printer replace the configuration files with the files in the
|
||||
// example_configurations/SCARA directory.
|
||||
//
|
||||
|
||||
@ -65,7 +65,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
||||
#define MOTHERBOARD BOARD_RAMPS_13_EFB
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
@ -79,10 +79,17 @@ Here are some standard links for getting your machine calibrated:
|
||||
// :[1,2,3,4]
|
||||
#define EXTRUDERS 1
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
// :{1:'ATX',2:'X-Box 360'}
|
||||
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
@ -131,9 +138,9 @@ Here are some standard links for getting your machine calibrated:
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
// :{ 0: "Not used", 4: "10k !! do not use for a hotend. Bad resolution at high temp. !!", 1: "100k / 4.7k - EPCOS", 51: "100k / 1k - EPCOS", 6: "100k / 4.7k EPCOS - Not as accurate as Table 1", 5: "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 7: "100k / 4.7k Honeywell 135-104LAG-J01", 71: "100k / 4.7k Honeywell 135-104LAF-J01", 8: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", 9: "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", 10: "100k / 4.7k RS 198-961", 11: "100k / 4.7k beta 3950 1%", 12: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", 13: "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", 60: "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", 55: "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 2: "200k / 4.7k - ATC Semitec 204GT-2", 52: "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", 3: "Mendel-parts / 4.7k", 1047: "Pt1000 / 4.7k", 1010: "Pt1000 / 1k (non standard)", 20: "PT100 (Ultimainboard V2.x)", 147: "Pt100 / 4.7k", 110: "Pt100 / 1k (non-standard)", 998: "Dummy 1", 999: "Dummy 2" }
|
||||
#define TEMP_SENSOR_0 -1
|
||||
#define TEMP_SENSOR_1 -1
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
@ -327,6 +334,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
||||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
// #define ENDSTOPPULLUP_ZPROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
@ -336,10 +344,16 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// @section machine
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
// this has no effect.
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
@ -361,9 +375,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// @section extruder
|
||||
|
||||
@ -391,8 +405,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS 205
|
||||
#define Y_MAX_POS 205
|
||||
#define X_MAX_POS 200
|
||||
#define Y_MAX_POS 200
|
||||
#define Z_MAX_POS 200
|
||||
|
||||
//===========================================================================
|
||||
@ -561,18 +575,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
@ -614,11 +623,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 180
|
||||
#define PLA_PREHEAT_HPB_TEMP 70
|
||||
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
#define ABS_PREHEAT_HOTEND_TEMP 240
|
||||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
#define ABS_PREHEAT_HPB_TEMP 110
|
||||
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
//==============================LCD and SD support=============================
|
||||
// @section lcd
|
||||
@ -626,7 +635,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
|
||||
// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
|
||||
@ -730,7 +739,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
// #define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
@ -784,7 +793,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
||||
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
|
||||
//#define FILAMENT_LCD_DISPLAY
|
||||
|
||||
@ -192,7 +192,7 @@
|
||||
#define X_HOME_BUMP_MM 5
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
#define Z_HOME_BUMP_MM 2
|
||||
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
// @section machine
|
||||
@ -335,7 +335,7 @@
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
#define D_FILAMENT 2.85
|
||||
#define STEPS_MM_E 836
|
||||
#endif // ADVANCE
|
||||
#endif
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
|
||||
@ -10,10 +10,11 @@
|
||||
#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0
|
||||
#define BOARD_SETHI 20 // Sethi 3D_1
|
||||
#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2
|
||||
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Extruder, Fan, Bed)
|
||||
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Bed)
|
||||
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Extruder, Fan, Fan)
|
||||
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Fan)
|
||||
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like)
|
||||
#define BOARD_DUEMILANOVE_328P 4 // Duemilanove w/ ATMega328P pin assignments
|
||||
#define BOARD_GEN6 5 // Gen6
|
||||
#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe
|
||||
@ -28,14 +29,15 @@
|
||||
#define BOARD_ULTIMAKER 7 // Ultimaker
|
||||
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
#define BOARD_3DRAG 77 // 3Drag
|
||||
#define BOARD_K8200 78 // Vellemann K8200 (derived from 3Drag)
|
||||
#define BOARD_3DRAG 77 // 3Drag Controller
|
||||
#define BOARD_K8200 78 // Vellemann K8200 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_TEENSYLU 8 // Teensylu
|
||||
#define BOARD_RUMBA 80 // Rumba
|
||||
#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286)
|
||||
#define BOARD_BRAINWAVE 82 // Brainwave (AT90USB646)
|
||||
#define BOARD_SAV_MKI 83 // SAV Mk-I (AT90USB1286)
|
||||
#define BOARD_TEENSY2 84 // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
#define BOARD_BRAINWAVE_PRO 85 // Brainwave Pro (AT90USB1286)
|
||||
#define BOARD_GEN3_PLUS 9 // Gen3+
|
||||
#define BOARD_GEN3_MONOLITHIC 22 // Gen3 Monolithic Electronics
|
||||
#define BOARD_MEGATRONICS 70 // Megatronics
|
||||
@ -50,10 +52,11 @@
|
||||
#define BOARD_LEAPFROG 999 // Leapfrog
|
||||
#define BOARD_WITBOX 41 // bq WITBOX
|
||||
#define BOARD_HEPHESTOS 42 // bq Prusa i3 Hephestos
|
||||
#define BOARD_BAM_DICE 401 // 2PrintBeta BAM&DICE with STK drivers
|
||||
#define BOARD_BAM_DICE_DUE 402 // 2PrintBeta BAM&DICE Due with STK drivers
|
||||
|
||||
#define BOARD_99 99 // This is in pins.h but...?
|
||||
|
||||
#define MB(board) (MOTHERBOARD==BOARD_##board)
|
||||
#define IS_RAMPS (MB(RAMPS_OLD) || MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF))
|
||||
|
||||
#endif //__BOARDS_H
|
||||
|
||||
@ -11,28 +11,35 @@
|
||||
//
|
||||
// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h"
|
||||
// ==> ALSO TRY ALL AVAILABLE LANGUAGE OPTIONS
|
||||
// See also documentation/LCDLanguageFont.md
|
||||
|
||||
// Languages
|
||||
// en English
|
||||
// pl Polish
|
||||
// fr French
|
||||
// de German
|
||||
// es Spanish
|
||||
// ru Russian
|
||||
// it Italian
|
||||
// pt Portuguese
|
||||
// pt-br Portuguese (Brazil)
|
||||
// fi Finnish
|
||||
// an Aragonese
|
||||
// nl Dutch
|
||||
// ca Catalan
|
||||
// eu Basque-Euskera
|
||||
// en English
|
||||
// pl Polish
|
||||
// fr French
|
||||
// de German
|
||||
// es Spanish
|
||||
// ru Russian
|
||||
// it Italian
|
||||
// pt Portuguese
|
||||
// pt-br Portuguese (Brazil)
|
||||
// fi Finnish
|
||||
// an Aragonese
|
||||
// nl Dutch
|
||||
// ca Catalan
|
||||
// eu Basque-Euskera
|
||||
// kana Japanese
|
||||
// kana_utf Japanese
|
||||
|
||||
#ifndef LANGUAGE_INCLUDE
|
||||
// pick your language from the list above
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
#endif
|
||||
|
||||
#ifdef HAS_AUTOMATIC_VERSIONING
|
||||
#include "_Version.h"
|
||||
#endif
|
||||
|
||||
#define PROTOCOL_VERSION "1.0"
|
||||
|
||||
#if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2)
|
||||
@ -56,18 +63,37 @@
|
||||
#elif MB(HEPHESTOS)
|
||||
#define MACHINE_NAME "HEPHESTOS"
|
||||
#define FIRMWARE_URL "http://www.bq.com/gb/downloads-prusa-i3-hephestos.html"
|
||||
#else // Default firmware set to Mendel
|
||||
#define MACHINE_NAME "Mendel"
|
||||
#define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
|
||||
#elif MB(BRAINWAVE_PRO)
|
||||
#define MACHINE_NAME "Kossel Pro"
|
||||
#ifndef FIRMWARE_URL
|
||||
#define FIRMWARE_URL "https://github.com/OpenBeamUSA/Marlin/"
|
||||
#endif
|
||||
#else
|
||||
#ifndef MACHINE_NAME
|
||||
#define MACHINE_NAME "Mendel"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifdef CUSTOM_MENDEL_NAME
|
||||
#warning CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
|
||||
#define CUSTOM_MACHINE_NAME CUSTOM_MENDEL_NAME
|
||||
#endif
|
||||
|
||||
#ifdef CUSTOM_MACHINE_NAME
|
||||
#undef MACHINE_NAME
|
||||
#define MACHINE_NAME CUSTOM_MENDEL_NAME
|
||||
#define MACHINE_NAME CUSTOM_MACHINE_NAME
|
||||
#endif
|
||||
|
||||
#ifndef FIRMWARE_URL
|
||||
#define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin"
|
||||
#endif
|
||||
|
||||
#ifndef BUILD_VERSION
|
||||
#define BUILD_VERSION "V1; Sprinter/grbl mashup for gen6"
|
||||
#endif
|
||||
|
||||
#ifndef MACHINE_UUID
|
||||
#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
#endif
|
||||
|
||||
|
||||
@ -114,7 +140,7 @@
|
||||
#define MSG_HEATING_COMPLETE "Heating done."
|
||||
#define MSG_BED_HEATING "Bed Heating."
|
||||
#define MSG_BED_DONE "Bed done."
|
||||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
|
||||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin " BUILD_VERSION " FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
|
||||
#define MSG_COUNT_X " Count X: "
|
||||
#define MSG_ERR_KILLED "Printer halted. kill() called!"
|
||||
#define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
|
||||
@ -122,12 +148,15 @@
|
||||
#define MSG_UNKNOWN_COMMAND "Unknown command: \""
|
||||
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
|
||||
#define MSG_INVALID_EXTRUDER "Invalid extruder"
|
||||
#define MSG_INVALID_SOLENOID "Invalid solenoid"
|
||||
#define MSG_X_MIN "x_min: "
|
||||
#define MSG_X_MAX "x_max: "
|
||||
#define MSG_Y_MIN "y_min: "
|
||||
#define MSG_Y_MAX "y_max: "
|
||||
#define MSG_Z_MIN "z_min: "
|
||||
#define MSG_Z_MAX "z_max: "
|
||||
#define MSG_Z2_MAX "z2_max: "
|
||||
#define MSG_Z_PROBE "z_probe: "
|
||||
#define MSG_M119_REPORT "Reporting endstop status"
|
||||
#define MSG_ENDSTOP_HIT "TRIGGERED"
|
||||
#define MSG_ENDSTOP_OPEN "open"
|
||||
@ -160,68 +189,48 @@
|
||||
|
||||
#define MSG_ERR_EEPROM_WRITE "Error writing to EEPROM!"
|
||||
|
||||
// temperature.cpp strings
|
||||
#define MSG_PID_AUTOTUNE "PID Autotune"
|
||||
#define MSG_PID_AUTOTUNE_START MSG_PID_AUTOTUNE " start"
|
||||
#define MSG_PID_AUTOTUNE_FAILED MSG_PID_AUTOTUNE " failed!"
|
||||
#define MSG_PID_BAD_EXTRUDER_NUM MSG_PID_AUTOTUNE_FAILED " Bad extruder number"
|
||||
#define MSG_PID_TEMP_TOO_HIGH MSG_PID_AUTOTUNE_FAILED " Temperature too high"
|
||||
#define MSG_PID_TIMEOUT MSG_PID_AUTOTUNE_FAILED " timeout"
|
||||
#define MSG_BIAS " bias: "
|
||||
#define MSG_D " d: "
|
||||
#define MSG_T_MIN " min: "
|
||||
#define MSG_T_MAX " max: "
|
||||
#define MSG_KU " Ku: "
|
||||
#define MSG_TU " Tu: "
|
||||
#define MSG_CLASSIC_PID " Classic PID "
|
||||
#define MSG_KP " Kp: "
|
||||
#define MSG_KI " Ki: "
|
||||
#define MSG_KD " Kd: "
|
||||
#define MSG_OK_B "ok B:"
|
||||
#define MSG_OK_T "ok T:"
|
||||
#define MSG_AT " @:"
|
||||
#define MSG_PID_AUTOTUNE_FINISHED MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
|
||||
#define MSG_PID_DEBUG " PID_DEBUG "
|
||||
#define MSG_PID_DEBUG_INPUT ": Input "
|
||||
#define MSG_PID_DEBUG_OUTPUT " Output "
|
||||
#define MSG_PID_DEBUG_PTERM " pTerm "
|
||||
#define MSG_PID_DEBUG_ITERM " iTerm "
|
||||
#define MSG_PID_DEBUG_DTERM " dTerm "
|
||||
#define MSG_HEATING_FAILED "Heating failed"
|
||||
#define MSG_EXTRUDER_SWITCHED_OFF "Extruder switched off. Temperature difference between temp sensors is too high !"
|
||||
|
||||
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !"
|
||||
#define MSG_THERMAL_RUNAWAY_STOP "Thermal Runaway, system stopped! Heater_ID: "
|
||||
#define MSG_SWITCHED_OFF_MAX " switched off. MAXTEMP triggered !!"
|
||||
#define MSG_MINTEMP_EXTRUDER_OFF ": Extruder switched off. MINTEMP triggered !"
|
||||
#define MSG_MAXTEMP_EXTRUDER_OFF ": Extruder" MSG_SWITCHED_OFF_MAX
|
||||
#define MSG_MAXTEMP_BED_OFF "Heated bed" MSG_SWITCHED_OFF_MAX
|
||||
|
||||
// LCD Menu Messages
|
||||
|
||||
// Add your own character. Reference: https://github.com/MarlinFirmware/Marlin/pull/1434 photos
|
||||
// and https://www.sparkfun.com/datasheets/LCD/HD44780.pdf page 17-18
|
||||
#ifdef DOGLCD
|
||||
#define STR_Ae "\304" // 'Ä' U8glib
|
||||
#define STR_ae "\344" // 'ä'
|
||||
#define STR_Oe "\326" // 'Ö'
|
||||
#define STR_oe STR_Oe // 'ö'
|
||||
#define STR_Ue "\334" // 'Ü'
|
||||
#define STR_ue STR_Ue // 'ü'
|
||||
#define STR_sz "\337" // 'ß'
|
||||
#define STR_h2 "\262" // '²'
|
||||
#define STR_h3 "\263" // '³'
|
||||
#define STR_Deg "\260" // '°'
|
||||
#define STR_THERMOMETER "\377"
|
||||
#else
|
||||
#ifdef DISPLAY_CHARSET_HD44780_JAPAN // HD44780 ROM Code: A00 (Japan)
|
||||
#define STR_ae "\xe1"
|
||||
#define STR_Ae STR_ae
|
||||
#define STR_oe "\357"
|
||||
#define STR_Oe STR_oe
|
||||
#define STR_ue "\365"
|
||||
#define STR_Ue STR_ue
|
||||
#define STR_sz "\342"
|
||||
#define STR_h2 "2"
|
||||
#define STR_h3 "3"
|
||||
#define STR_Deg "\271"
|
||||
#define STR_THERMOMETER "\002"
|
||||
#endif
|
||||
#ifdef DISPLAY_CHARSET_HD44780_WESTERN // HD44780 ROM Code: A02 (Western)
|
||||
#define STR_Ae "\216"
|
||||
#define STR_ae "\204"
|
||||
#define STR_Oe "\211"
|
||||
#define STR_oe "\204"
|
||||
#define STR_Ue "\212"
|
||||
#define STR_ue "\201"
|
||||
#define STR_sz "\160"
|
||||
#define STR_h2 "\262"
|
||||
#define STR_h3 "\263"
|
||||
#define STR_Deg "\337"
|
||||
#define STR_THERMOMETER "\002"
|
||||
#endif
|
||||
#if !(defined( DISPLAY_CHARSET_HD44780_JAPAN ) || defined( DISPLAY_CHARSET_HD44780_WESTERN ) || defined( DISPLAY_CHARSET_HD44780_CYRILLIC ))
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN
|
||||
#endif
|
||||
/*
|
||||
#define TESTSTRING000 "\000\001\002\003\004\005\006\007\010\011\012\013\014\015\016\017"
|
||||
#define TESTSTRING020 "\020\021\022\023\024\025\026\027\030\031\032\033\034\035\036\037"
|
||||
#define TESTSTRING040 "\040\041\042\043\044\045\046\047\050\051\052\053\054\055\056\057"
|
||||
#define TESTSTRING060 "\060\061\062\063\064\065\066\067\070\071\072\073\074\075\076\077"
|
||||
#define TESTSTRING100 "\100\101\102\103\104\105\106\107\110\111\112\113\114\115\116\117"
|
||||
#define TESTSTRING120 "\120\121\122\123\124\125\126\127\130\131\132\133\134\135\136\137"
|
||||
#define TESTSTRING140 "\140\141\142\143\144\145\146\147\150\151\152\153\154\155\156\157"
|
||||
#define TESTSTRING160 "\160\161\162\163\164\165\166\167\170\171\172\173\174\175\176\177"
|
||||
#define TESTSTRING200 "\200\201\202\203\204\205\206\207\210\211\212\213\214\215\216\217"
|
||||
#define TESTSTRING220 "\220\221\222\223\224\225\226\227\230\231\232\233\234\235\236\237"
|
||||
#define TESTSTRING240 "\240\241\242\243\244\245\246\247\250\251\252\253\254\255\256\257"
|
||||
#define TESTSTRING260 "\260\261\262\263\264\265\266\267\270\271\272\273\274\275\276\277"
|
||||
#define TESTSTRING300 "\300\301\302\303\304\305\306\307\310\311\312\313\314\315\316\317"
|
||||
#define TESTSTRING320 "\320\321\322\323\324\325\326\327\330\331\332\333\334\335\336\337"
|
||||
#define TESTSTRING340 "\340\341\342\343\344\345\346\347\350\351\352\353\354\355\356\357"
|
||||
#define TESTSTRING360 "\360\361\362\363\364\365\366\367\370\371\372\373\374\375\376\377"
|
||||
*/
|
||||
|
||||
#include LANGUAGE_INCLUDE
|
||||
#include "language_en.h"
|
||||
|
||||
Loading…
Reference in New Issue
Block a user