MPCNC/Firmware
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Merge pull request #6284 from thinkyhead/rc_wt150_rebase

Browse Source 
wt150 (Mightyboard Rev E) & RRD Full Graphic Smart Controller
This commit is contained in:
Scott Lahteine 2017-04-09 20:27:44 -05:00 committed by GitHub
commit 7a704af5e6
49 changed files with 3860 additions and 113 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
Marlin/Configuration.h
View File

@ -720,7 +720,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

2
Marlin/SanityCheck.h
View File

@ -770,7 +770,7 @@ static_assert(1 >= 0
*/
#if !HAS_HEATER_0
#error "HEATER_0_PIN not defined for this board."
#elif !PIN_EXISTS(TEMP_0)
#elif !PIN_EXISTS(TEMP_0) && !(defined(MAX6675_SS) && MAX6675_SS >= 0)
#error "TEMP_0_PIN not defined for this board."
#elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)
#error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."

91
Marlin/digipot_mcp4018.cpp Normal file
View File

@ -0,0 +1,91 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#include "MarlinConfig.h"
#if ENABLED(DIGIPOT_I2C) && ENABLED(DIGIPOT_MCP4018)
#include "Stream.h"
#include "utility/twi.h"
#include <SlowSoftI2CMaster.h> //https://github.com/stawel/SlowSoftI2CMaster
// Settings for the I2C based DIGIPOT (MCP4018) based on WT150
#define DIGIPOT_I2C_ADDRESS 0x2f
#define DIGIPOT_A4988_Rsx 0.250
#define DIGIPOT_A4988_Vrefmax 5.0
#define DIGIPOT_A4988_MAX_VALUE 127
#define DIGIPOT_A4988_Itripmax(Vref) ((Vref)/(8.0*DIGIPOT_A4988_Rsx))
#define DIGIPOT_A4988_FACTOR (DIGIPOT_A4988_MAX_VALUE/DIGIPOT_A4988_Itripmax(DIGIPOT_A4988_Vrefmax))
//TODO: MAX_CURRENT -0.5A ?? (currently set to 2A, max possible current 2.5A)
#define DIGIPOT_A4988_MAX_CURRENT (DIGIPOT_A4988_Itripmax(DIGIPOT_A4988_Vrefmax) - 0.5)
static byte current_to_wiper(float current) {
return byte(ceil(float((DIGIPOT_A4988_FACTOR * current))));
}
static uint8_t sda_pins[DIGIPOT_I2C_NUM_CHANNELS] = {
DIGIPOTS_I2C_SDA_X,
DIGIPOTS_I2C_SDA_Y,
DIGIPOTS_I2C_SDA_Z,
DIGIPOTS_I2C_SDA_E0,
DIGIPOTS_I2C_SDA_E1,
};
static SlowSoftI2CMaster pots[DIGIPOT_I2C_NUM_CHANNELS] = {
SlowSoftI2CMaster { sda_pins[0], DIGIPOTS_I2C_SCL },
SlowSoftI2CMaster { sda_pins[1], DIGIPOTS_I2C_SCL },
SlowSoftI2CMaster { sda_pins[2], DIGIPOTS_I2C_SCL },
SlowSoftI2CMaster { sda_pins[3], DIGIPOTS_I2C_SCL },
SlowSoftI2CMaster { sda_pins[4], DIGIPOTS_I2C_SCL }
};
static void i2c_send(int channel, byte v) {
if (WITHIN(channel, 0, DIGIPOT_I2C_NUM_CHANNELS - 1)) {
pots[channel].i2c_start(((DIGIPOT_I2C_ADDRESS) << 1) | I2C_WRITE);
pots[channel].i2c_write(v);
pots[channel].i2c_stop();
}
}
// This is for the MCP4018 I2C based digipot
void digipot_i2c_set_current(int channel, float current) {
current = min(max(current, 0.0f), float(DIGIPOT_A4988_MAX_CURRENT));
i2c_send(channel, current_to_wiper(current));
}
void digipot_i2c_init() {
const float digipot_motor_current[] = DIGIPOT_I2C_MOTOR_CURRENTS;
for (uint8_t i = 0; i < DIGIPOT_I2C_NUM_CHANNELS; i++)
pots[i].i2c_init();
// setup initial currents as defined in Configuration_adv.h
for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++)
digipot_i2c_set_current(i, digipot_motor_current[i]);
}
#endif // DIGIPOT_I2C && DIGIPOT_MCP4018

2
Marlin/digipot_mcp4451.cpp
View File

@ -22,7 +22,7 @@
#include "MarlinConfig.h"
#if ENABLED(DIGIPOT_I2C)
#if ENABLED(DIGIPOT_I2C) && DISABLED(DIGIPOT_MCP4018)
#include "Stream.h"
#include "utility/twi.h"

1
Marlin/example_configurations/Cartesio/Configuration.h
View File

@ -719,7 +719,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 1

6
Marlin/example_configurations/Cartesio/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/Felix/Configuration.h
View File

@ -703,7 +703,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/Felix/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/Felix/DUAL/Configuration.h
View File

@ -703,7 +703,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

1
Marlin/example_configurations/Hephestos/Configuration.h
View File

@ -711,7 +711,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/Hephestos/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/Hephestos_2/Configuration.h
View File

@ -714,7 +714,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -2
#define Z_PROBE_OFFSET_RANGE_MAX 0
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/Hephestos_2/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -422,6 +421,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

6
Marlin/example_configurations/K8200/Configuration_adv.h
View File

@ -269,7 +269,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -420,8 +419,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -434,6 +433,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/K8400/Configuration.h
View File

@ -720,7 +720,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/K8400/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/K8400/Dual-head/Configuration.h
View File

@ -720,7 +720,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

1
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
View File

@ -720,7 +720,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

1
Marlin/example_configurations/RigidBot/Configuration.h
View File

@ -719,7 +719,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/RigidBot/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/SCARA/Configuration.h
View File

@ -735,7 +735,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/SCARA/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/TAZ4/Configuration.h
View File

@ -740,7 +740,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/TAZ4/Configuration_adv.h
View File

@ -264,7 +264,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -415,8 +414,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -429,6 +428,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

19
Marlin/example_configurations/TinyBoy2/Configuration.h
View File

@ -974,7 +974,7 @@
#define UBL_PROBE_PT_2_Y 20
#define UBL_PROBE_PT_3_X 180
#define UBL_PROBE_PT_3_Y 20
#define UBL_G26_MESH_EDITING // Enable G26 mesh editing
//#define UBL_G26_MESH_EDITING // Enable G26 mesh editing
#elif ENABLED(MESH_BED_LEVELING)
@ -990,6 +990,17 @@
#endif // BED_LEVELING
/**
* Use the LCD controller for bed leveling
* Requires MESH_BED_LEVELING or PROBE_MANUALLY
*/
//#define LCD_BED_LEVELING
#if ENABLED(LCD_BED_LEVELING)
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
#define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
@ -1537,13 +1548,13 @@
// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
// be used to mitigate the associated resolution loss. If enabled,
// some of the PWM cycles are stretched so on average the wanted
// some of the PWM cycles are stretched so on average the desired
// duty cycle is attained.
//#define SOFT_PWM_DITHER
// Temperature status LEDs that display the hotend and bed temperature.
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
// Otherwise the RED led is on. There is 1C hysteresis.
// If all hotends, bed temperature, and target temperature are under 54C
// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
//#define TEMP_STAT_LEDS
// M240 Triggers a camera by emulating a Canon RC-1 Remote

35
Marlin/example_configurations/TinyBoy2/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -286,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine/test this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS
@ -394,18 +394,36 @@
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
/**
* @section stepper motor current
*
* Some boards have a means of setting the stepper motor current via firmware.
*
* The power on motor currents are set by:
* PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
* known compatible chips: A4982
* DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
* M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
* M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
*/
//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
//#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
#define DIGIPOT_I2C_NUM_CHANNELS 8
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO
//===========================================================================
//=============================Additional Features===========================
@ -648,6 +666,7 @@
//#define BEZIER_CURVE_SUPPORT
// G38.2 and G38.3 Probe Target
// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch
//#define G38_PROBE_TARGET
#if ENABLED(G38_PROBE_TARGET)
#define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)

1
Marlin/example_configurations/WITBOX/Configuration.h
View File

@ -711,7 +711,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/WITBOX/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/adafruit/ST7565/Configuration.h
View File

@ -720,7 +720,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -409,8 +408,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -423,6 +422,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/delta/generic/Configuration.h
View File

@ -822,7 +822,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/delta/generic/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -409,8 +408,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -423,6 +422,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/delta/kossel_mini/Configuration.h
View File

@ -817,7 +817,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -409,8 +408,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -423,6 +422,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

6
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
View File

@ -261,7 +261,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -414,8 +413,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -428,6 +427,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/delta/kossel_xl/Configuration.h
View File

@ -833,7 +833,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -409,8 +408,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -423,6 +422,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1
Marlin/example_configurations/makibox/Configuration.h
View File

@ -723,7 +723,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 0

6
Marlin/example_configurations/makibox/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 4 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.7, 1.7, 1.7, 1.7 } // 5DPRINT

1
Marlin/example_configurations/tvrrug/Round2/Configuration.h
View File

@ -716,7 +716,6 @@
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{ 0:'Low', 1:'High' }
#define X_ENABLE_ON 1

6
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
View File

@ -256,7 +256,6 @@
#define INVERT_X2_VS_X_DIR true
#endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
@ -407,8 +406,8 @@
* known compatible chips: AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips: MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT & AZTEEG_X3_PRO
* known compatible chips: MCP4451
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
* known compatible chips: MCP4451, MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD.
* M907 - applies to all.
@ -421,6 +420,7 @@
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
//#define DIGIPOT_I2C
//#define DIGIPOT_MCP4018
#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO

1590
Marlin/example_configurations/wt150/Configuration.h Normal file
View File

File diff suppressed because it is too large Load Diff

1116
Marlin/example_configurations/wt150/Configuration_adv.h Normal file
View File

File diff suppressed because it is too large Load Diff

131
Marlin/pins_MIGHTYBOARD_REVE.h
View File

@ -129,6 +129,9 @@
#define THERMO_CS1 5 // E3
#define THERMO_CS2 2 // E4
#define MAX6675_SS THERMO_CS1
#define MAX6675_SCK_PIN THERMO_SCK_PIN
#define MAX6675_DO_PIN THERMO_DO_PIN
//
// Augmentation for auto-assigning plugs
//
@ -137,7 +140,7 @@
// With no heated bed, an additional 24V fan is possible.
//
#define MOSFET_A_PIN 6 // H3
#define MOSFET_B_PIN 9 // B5
#define MOSFET_B_PIN 11 // B5
#define MOSFET_C_PIN 45 // L4
#define MOSFET_D_PIN 44 // L5
@ -181,8 +184,8 @@
//
// Extruder Auto Fan Pins
//
#define EXTRUDER_0_AUTO_FAN 7 // H4
#define EXTRUDER_1_AUTO_FAN 12 // B6
#define ORIG_E0_AUTO_FAN_PIN 7 // H4
#define ORIG_E1_AUTO_FAN_PIN 12 // B6
//
// Misc. Functions
@ -194,29 +197,117 @@
//
// LCD / Controller
//
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#define BEEPER_PIN 4 // G5
#define LCD_PINS_RS 33 // C4, LCD-STROBE
#define LCD_PINS_ENABLE 72 // J2, LEFT
#define LCD_PINS_D4 35 // C2, LCD-CLK
#define LCD_PINS_D5 32 // C5, RLED
#define LCD_PINS_D6 34 // C3, LCD-DATA
#define LCD_PINS_D7 31 // C6, GLED
#define BTN_EN2 75 // J4, UP
#define BTN_EN1 73 // J3, DOWN
//STOP button connected as KILL_PIN
#define KILL_PIN 14 // J1, RIGHT
//KILL - not connected
#define BEEPER_PIN 8 // H5, SD_WP
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
//on board leds
#define STAT_LED_RED_LED SERVO0_PIN // C1 (1280-EX1, DEBUG2)
#define STAT_LED_BLUE_PIN SERVO1_PIN // C0 (1280-EX2, DEBUG3)
#else
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#define BEEPER_PIN 4 // G5
#define STAT_LED_RED_PIN 32 // C5
#define STAT_LED_BLUE_PIN 31 // C6 (Actually green)
#endif
#define STAT_LED_RED 32 // C5
#define STAT_LED_BLUE 31 // C6 (Actually green)
//
// SD Card
//
#define SDSS 53 // B0
#define SD_DETECT_PIN 30 // C7
#define SD_DETECT_PIN 9 // H6
#define MAX_PIN THERMO_SCK_PIN
//check if all pins are defined in mega/pins_arduino.h
#include <Arduino.h>
static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"
"to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below");
/* in [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h
change:
#define NUM_DIGITAL_PINS 70
to:
#define NUM_DIGITAL_PINS 80
to digital_pin_to_port_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
....
PG , // PG 4 ** 70 **
PG , // PG 3 ** 71 **
PJ , // PJ 2 ** 72 **
PJ , // PJ 3 ** 73 **
PJ , // PJ 7 ** 74 **
PJ , // PJ 4 ** 75 **
PJ , // PJ 5 ** 76 **
PJ , // PJ 6 ** 77 **
PE , // PE 2 ** 78 **
PE , // PE 6 ** 79 **
};
to digital_pin_to_bit_mask_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
....
_BV( 4 ) , // PG 4 ** 70 **
_BV( 3 ) , // PG 3 ** 71 **
_BV( 2 ) , // PJ 2 ** 72 **
_BV( 3 ) , // PJ 3 ** 73 **
_BV( 7 ) , // PJ 7 ** 74 **
_BV( 4 ) , // PJ 4 ** 75 **
_BV( 5 ) , // PJ 5 ** 76 **
_BV( 6 ) , // PJ 6 ** 77 **
_BV( 2 ) , // PE 2 ** 78 **
_BV( 6 ) , // PE 6 ** 79 **
};
to digital_pin_to_timer_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
....
NOT_ON_TIMER , // PG 4 ** 70 **
NOT_ON_TIMER , // PG 3 ** 71 **
NOT_ON_TIMER , // PJ 2 ** 72 **
NOT_ON_TIMER , // PJ 3 ** 73 **
NOT_ON_TIMER , // PJ 7 ** 74 **
NOT_ON_TIMER , // PJ 4 ** 75 **
NOT_ON_TIMER , // PJ 5 ** 76 **
NOT_ON_TIMER , // PJ 6 ** 77 **
NOT_ON_TIMER , // PE 2 ** 78 **
NOT_ON_TIMER , // PE 6 ** 79 **
};
*/

770
Marlin/softspi.h Normal file
View File

@ -0,0 +1,770 @@
//https://github.com/niteris/ArduinoSoftSpi
#include <Arduino.h>
#ifdef __arm__
#ifdef CORE_TEENSY
//------------------------------------------------------------------------------
/** read pin value
* @param[in] pin Arduino pin number
* @return value read
*/
static inline __attribute__((always_inline))
bool fastDigitalRead(uint8_t pin) {
return *portInputRegister(pin);
}
//------------------------------------------------------------------------------
/** Set pin value
* @param[in] pin Arduino pin number
* @param[in] level value to write
*/
static inline __attribute__((always_inline))
void fastDigitalWrite(uint8_t pin, bool value) {
if (value) {
*portSetRegister(pin) = 1;
} else {
*portClearRegister(pin) = 1;
}
}
#else // CORE_TEENSY
//------------------------------------------------------------------------------
/** read pin value
* @param[in] pin Arduino pin number
* @return value read
*/
static inline __attribute__((always_inline))
bool fastDigitalRead(uint8_t pin){
return g_APinDescription[pin].pPort->PIO_PDSR & g_APinDescription[pin].ulPin;
}
//------------------------------------------------------------------------------
/** Set pin value
* @param[in] pin Arduino pin number
* @param[in] level value to write
*/
static inline __attribute__((always_inline))
void fastDigitalWrite(uint8_t pin, bool value){
if(value) {
g_APinDescription[pin].pPort->PIO_SODR = g_APinDescription[pin].ulPin;
} else {
g_APinDescription[pin].pPort->PIO_CODR = g_APinDescription[pin].ulPin;
}
}
#endif // CORE_TEENSY
//------------------------------------------------------------------------------
inline void fastDigitalToggle(uint8_t pin) {
fastDigitalWrite(pin, !fastDigitalRead(pin));
}
//------------------------------------------------------------------------------
inline void fastPinMode(uint8_t pin, bool mode) {pinMode(pin, mode);}
#else // __arm__
#include <avr/io.h>
#include <util/atomic.h>
//------------------------------------------------------------------------------
/**
* @class pin_map_t
* @brief struct for mapping digital pins
*/
struct pin_map_t {
volatile uint8_t* ddr; /**< address of DDR for this pin */
volatile uint8_t* pin; /**< address of PIN for this pin */
volatile uint8_t* port; /**< address of PORT for this pin */
uint8_t bit; /**< bit number for this pin */
};
//------------------------------------------------------------------------------
#if defined(__AVR_ATmega168__)\
||defined(__AVR_ATmega168P__)\
||defined(__AVR_ATmega328P__)
// 168 and 328 Arduinos
const static pin_map_t pinMap[] = {
{&DDRD, &PIND, &PORTD, 0}, // D0 0
{&DDRD, &PIND, &PORTD, 1}, // D1 1
{&DDRD, &PIND, &PORTD, 2}, // D2 2
{&DDRD, &PIND, &PORTD, 3}, // D3 3
{&DDRD, &PIND, &PORTD, 4}, // D4 4
{&DDRD, &PIND, &PORTD, 5}, // D5 5
{&DDRD, &PIND, &PORTD, 6}, // D6 6
{&DDRD, &PIND, &PORTD, 7}, // D7 7
{&DDRB, &PINB, &PORTB, 0}, // B0 8
{&DDRB, &PINB, &PORTB, 1}, // B1 9
{&DDRB, &PINB, &PORTB, 2}, // B2 10
{&DDRB, &PINB, &PORTB, 3}, // B3 11
{&DDRB, &PINB, &PORTB, 4}, // B4 12
{&DDRB, &PINB, &PORTB, 5}, // B5 13
{&DDRC, &PINC, &PORTC, 0}, // C0 14
{&DDRC, &PINC, &PORTC, 1}, // C1 15
{&DDRC, &PINC, &PORTC, 2}, // C2 16
{&DDRC, &PINC, &PORTC, 3}, // C3 17
{&DDRC, &PINC, &PORTC, 4}, // C4 18
{&DDRC, &PINC, &PORTC, 5} // C5 19
};
//------------------------------------------------------------------------------
#elif defined(__AVR_ATmega1280__)\
|| defined(__AVR_ATmega2560__)
// Mega
static const pin_map_t pinMap[] = {
{&DDRE, &PINE, &PORTE, 0}, // E0 0
{&DDRE, &PINE, &PORTE, 1}, // E1 1
{&DDRE, &PINE, &PORTE, 4}, // E4 2
{&DDRE, &PINE, &PORTE, 5}, // E5 3
{&DDRG, &PING, &PORTG, 5}, // G5 4
{&DDRE, &PINE, &PORTE, 3}, // E3 5
{&DDRH, &PINH, &PORTH, 3}, // H3 6
{&DDRH, &PINH, &PORTH, 4}, // H4 7
{&DDRH, &PINH, &PORTH, 5}, // H5 8
{&DDRH, &PINH, &PORTH, 6}, // H6 9
{&DDRB, &PINB, &PORTB, 4}, // B4 10
{&DDRB, &PINB, &PORTB, 5}, // B5 11
{&DDRB, &PINB, &PORTB, 6}, // B6 12
{&DDRB, &PINB, &PORTB, 7}, // B7 13
{&DDRJ, &PINJ, &PORTJ, 1}, // J1 14
{&DDRJ, &PINJ, &PORTJ, 0}, // J0 15
{&DDRH, &PINH, &PORTH, 1}, // H1 16
{&DDRH, &PINH, &PORTH, 0}, // H0 17
{&DDRD, &PIND, &PORTD, 3}, // D3 18
{&DDRD, &PIND, &PORTD, 2}, // D2 19
{&DDRD, &PIND, &PORTD, 1}, // D1 20
{&DDRD, &PIND, &PORTD, 0}, // D0 21
{&DDRA, &PINA, &PORTA, 0}, // A0 22
{&DDRA, &PINA, &PORTA, 1}, // A1 23
{&DDRA, &PINA, &PORTA, 2}, // A2 24
{&DDRA, &PINA, &PORTA, 3}, // A3 25
{&DDRA, &PINA, &PORTA, 4}, // A4 26
{&DDRA, &PINA, &PORTA, 5}, // A5 27
{&DDRA, &PINA, &PORTA, 6}, // A6 28
{&DDRA, &PINA, &PORTA, 7}, // A7 29
{&DDRC, &PINC, &PORTC, 7}, // C7 30
{&DDRC, &PINC, &PORTC, 6}, // C6 31
{&DDRC, &PINC, &PORTC, 5}, // C5 32
{&DDRC, &PINC, &PORTC, 4}, // C4 33
{&DDRC, &PINC, &PORTC, 3}, // C3 34
{&DDRC, &PINC, &PORTC, 2}, // C2 35
{&DDRC, &PINC, &PORTC, 1}, // C1 36
{&DDRC, &PINC, &PORTC, 0}, // C0 37
{&DDRD, &PIND, &PORTD, 7}, // D7 38
{&DDRG, &PING, &PORTG, 2}, // G2 39
{&DDRG, &PING, &PORTG, 1}, // G1 40
{&DDRG, &PING, &PORTG, 0}, // G0 41
{&DDRL, &PINL, &PORTL, 7}, // L7 42
{&DDRL, &PINL, &PORTL, 6}, // L6 43
{&DDRL, &PINL, &PORTL, 5}, // L5 44
{&DDRL, &PINL, &PORTL, 4}, // L4 45
{&DDRL, &PINL, &PORTL, 3}, // L3 46
{&DDRL, &PINL, &PORTL, 2}, // L2 47
{&DDRL, &PINL, &PORTL, 1}, // L1 48
{&DDRL, &PINL, &PORTL, 0}, // L0 49
{&DDRB, &PINB, &PORTB, 3}, // B3 50
{&DDRB, &PINB, &PORTB, 2}, // B2 51
{&DDRB, &PINB, &PORTB, 1}, // B1 52
{&DDRB, &PINB, &PORTB, 0}, // B0 53
{&DDRF, &PINF, &PORTF, 0}, // F0 54
{&DDRF, &PINF, &PORTF, 1}, // F1 55
{&DDRF, &PINF, &PORTF, 2}, // F2 56
{&DDRF, &PINF, &PORTF, 3}, // F3 57
{&DDRF, &PINF, &PORTF, 4}, // F4 58
{&DDRF, &PINF, &PORTF, 5}, // F5 59
{&DDRF, &PINF, &PORTF, 6}, // F6 60
{&DDRF, &PINF, &PORTF, 7}, // F7 61
{&DDRK, &PINK, &PORTK, 0}, // K0 62
{&DDRK, &PINK, &PORTK, 1}, // K1 63
{&DDRK, &PINK, &PORTK, 2}, // K2 64
{&DDRK, &PINK, &PORTK, 3}, // K3 65
{&DDRK, &PINK, &PORTK, 4}, // K4 66
{&DDRK, &PINK, &PORTK, 5}, // K5 67
{&DDRK, &PINK, &PORTK, 6}, // K6 68
{&DDRK, &PINK, &PORTK, 7}, // K7 69
//pins_MIGHTYBOARD_REVE.h
{&DDRG, &PING, &PORTG, 4}, // G4 70
{&DDRG, &PING, &PORTG, 3}, // G3 71
{&DDRJ, &PINJ, &PORTJ, 2}, // J2 72
{&DDRJ, &PINJ, &PORTJ, 3}, // J3 73
{&DDRJ, &PINJ, &PORTJ, 7}, // J7 74
{&DDRJ, &PINJ, &PORTJ, 4}, // J4 75
{&DDRJ, &PINJ, &PORTJ, 5}, // J5 76
{&DDRJ, &PINJ, &PORTJ, 6}, // J6 77
{&DDRE, &PINE, &PORTE, 2}, // E2 78
{&DDRE, &PINE, &PORTE, 6} // E6 79
};
//------------------------------------------------------------------------------
#elif defined(__AVR_ATmega1284P__)\
|| defined(__AVR_ATmega1284__)\
|| defined(__AVR_ATmega644P__)\
|| defined(__AVR_ATmega644__)\
|| defined(__AVR_ATmega64__)\
|| defined(__AVR_ATmega32__)\
|| defined(__AVR_ATmega324__)\
|| defined(__AVR_ATmega16__)
#ifdef defined(VARIANT_MIGHTY)
// Mighty Layout
static const pin_map_t pinMap[] = {
{&DDRB, &PINB, &PORTB, 0}, // B0 0
{&DDRB, &PINB, &PORTB, 1}, // B1 1
{&DDRB, &PINB, &PORTB, 2}, // B2 2
{&DDRB, &PINB, &PORTB, 3}, // B3 3
{&DDRB, &PINB, &PORTB, 4}, // B4 4
{&DDRB, &PINB, &PORTB, 5}, // B5 5
{&DDRB, &PINB, &PORTB, 6}, // B6 6
{&DDRB, &PINB, &PORTB, 7}, // B7 7
{&DDRD, &PIND, &PORTD, 0}, // D0 8
{&DDRD, &PIND, &PORTD, 1}, // D1 9
{&DDRD, &PIND, &PORTD, 2}, // D2 10
{&DDRD, &PIND, &PORTD, 3}, // D3 11
{&DDRD, &PIND, &PORTD, 4}, // D4 12
{&DDRD, &PIND, &PORTD, 5}, // D5 13
{&DDRD, &PIND, &PORTD, 6}, // D6 14
{&DDRD, &PIND, &PORTD, 7}, // D7 15
{&DDRC, &PINC, &PORTC, 0}, // C0 16
{&DDRC, &PINC, &PORTC, 1}, // C1 17
{&DDRC, &PINC, &PORTC, 2}, // C2 18
{&DDRC, &PINC, &PORTC, 3}, // C3 19
{&DDRC, &PINC, &PORTC, 4}, // C4 20
{&DDRC, &PINC, &PORTC, 5}, // C5 21
{&DDRC, &PINC, &PORTC, 6}, // C6 22
{&DDRC, &PINC, &PORTC, 7}, // C7 23
{&DDRA, &PINA, &PORTA, 0}, // A0 24
{&DDRA, &PINA, &PORTA, 1}, // A1 25
{&DDRA, &PINA, &PORTA, 2}, // A2 26
{&DDRA, &PINA, &PORTA, 3}, // A3 27
{&DDRA, &PINA, &PORTA, 4}, // A4 28
{&DDRA, &PINA, &PORTA, 5}, // A5 29
{&DDRA, &PINA, &PORTA, 6}, // A6 30
{&DDRA, &PINA, &PORTA, 7} // A7 31
};
#elif defined(VARIANT_BOBUINO)
// Bobuino Layout
static const pin_map_t pinMap[] = {
{&DDRD, &PIND, &PORTD, 0}, // D0 0
{&DDRD, &PIND, &PORTD, 1}, // D1 1
{&DDRD, &PIND, &PORTD, 2}, // D2 2
{&DDRD, &PIND, &PORTD, 3}, // D3 3
{&DDRB, &PINB, &PORTB, 0}, // B0 4
{&DDRB, &PINB, &PORTB, 1}, // B1 5
{&DDRB, &PINB, &PORTB, 2}, // B2 6
{&DDRB, &PINB, &PORTB, 3}, // B3 7
{&DDRD, &PIND, &PORTD, 5}, // D5 8
{&DDRD, &PIND, &PORTD, 6}, // D6 9
{&DDRB, &PINB, &PORTB, 4}, // B4 10
{&DDRB, &PINB, &PORTB, 5}, // B5 11
{&DDRB, &PINB, &PORTB, 6}, // B6 12
{&DDRB, &PINB, &PORTB, 7}, // B7 13
{&DDRA, &PINA, &PORTA, 7}, // A7 14
{&DDRA, &PINA, &PORTA, 6}, // A6 15
{&DDRA, &PINA, &PORTA, 5}, // A5 16
{&DDRA, &PINA, &PORTA, 4}, // A4 17
{&DDRA, &PINA, &PORTA, 3}, // A3 18
{&DDRA, &PINA, &PORTA, 2}, // A2 19
{&DDRA, &PINA, &PORTA, 1}, // A1 20
{&DDRA, &PINA, &PORTA, 0}, // A0 21
{&DDRC, &PINC, &PORTC, 0}, // C0 22
{&DDRC, &PINC, &PORTC, 1}, // C1 23
{&DDRC, &PINC, &PORTC, 2}, // C2 24
{&DDRC, &PINC, &PORTC, 3}, // C3 25
{&DDRC, &PINC, &PORTC, 4}, // C4 26
{&DDRC, &PINC, &PORTC, 5}, // C5 27
{&DDRC, &PINC, &PORTC, 6}, // C6 28
{&DDRC, &PINC, &PORTC, 7}, // C7 29
{&DDRD, &PIND, &PORTD, 4}, // D4 30
{&DDRD, &PIND, &PORTD, 7} // D7 31
};
#elif defined(VARIANT_STANDARD)
// Standard Layout
static const pin_map_t pinMap[] = {
{&DDRB, &PINB, &PORTB, 0}, // B0 0
{&DDRB, &PINB, &PORTB, 1}, // B1 1
{&DDRB, &PINB, &PORTB, 2}, // B2 2
{&DDRB, &PINB, &PORTB, 3}, // B3 3
{&DDRB, &PINB, &PORTB, 4}, // B4 4
{&DDRB, &PINB, &PORTB, 5}, // B5 5
{&DDRB, &PINB, &PORTB, 6}, // B6 6
{&DDRB, &PINB, &PORTB, 7}, // B7 7
{&DDRD, &PIND, &PORTD, 0}, // D0 8
{&DDRD, &PIND, &PORTD, 1}, // D1 9
{&DDRD, &PIND, &PORTD, 2}, // D2 10
{&DDRD, &PIND, &PORTD, 3}, // D3 11
{&DDRD, &PIND, &PORTD, 4}, // D4 12
{&DDRD, &PIND, &PORTD, 5}, // D5 13
{&DDRD, &PIND, &PORTD, 6}, // D6 14
{&DDRD, &PIND, &PORTD, 7}, // D7 15
{&DDRC, &PINC, &PORTC, 0}, // C0 16
{&DDRC, &PINC, &PORTC, 1}, // C1 17
{&DDRC, &PINC, &PORTC, 2}, // C2 18
{&DDRC, &PINC, &PORTC, 3}, // C3 19
{&DDRC, &PINC, &PORTC, 4}, // C4 20
{&DDRC, &PINC, &PORTC, 5}, // C5 21
{&DDRC, &PINC, &PORTC, 6}, // C6 22
{&DDRC, &PINC, &PORTC, 7}, // C7 23
{&DDRA, &PINA, &PORTA, 7}, // A7 24
{&DDRA, &PINA, &PORTA, 6}, // A6 25
{&DDRA, &PINA, &PORTA, 5}, // A5 26
{&DDRA, &PINA, &PORTA, 4}, // A4 27
{&DDRA, &PINA, &PORTA, 3}, // A3 28
{&DDRA, &PINA, &PORTA, 2}, // A2 29
{&DDRA, &PINA, &PORTA, 1}, // A1 30
{&DDRA, &PINA, &PORTA, 0} // A0 31
};
#else // VARIANT_MIGHTY
#error Undefined variant 1284, 644, 324, 64, 32
#endif // VARIANT_MIGHTY
//------------------------------------------------------------------------------
#elif defined(__AVR_ATmega32U4__)
#ifdef CORE_TEENSY
// Teensy 2.0
static const pin_map_t pinMap[] = {
{&DDRB, &PINB, &PORTB, 0}, // B0 0
{&DDRB, &PINB, &PORTB, 1}, // B1 1
{&DDRB, &PINB, &PORTB, 2}, // B2 2
{&DDRB, &PINB, &PORTB, 3}, // B3 3
{&DDRB, &PINB, &PORTB, 7}, // B7 4
{&DDRD, &PIND, &PORTD, 0}, // D0 5
{&DDRD, &PIND, &PORTD, 1}, // D1 6
{&DDRD, &PIND, &PORTD, 2}, // D2 7
{&DDRD, &PIND, &PORTD, 3}, // D3 8
{&DDRC, &PINC, &PORTC, 6}, // C6 9
{&DDRC, &PINC, &PORTC, 7}, // C7 10
{&DDRD, &PIND, &PORTD, 6}, // D6 11
{&DDRD, &PIND, &PORTD, 7}, // D7 12
{&DDRB, &PINB, &PORTB, 4}, // B4 13
{&DDRB, &PINB, &PORTB, 5}, // B5 14
{&DDRB, &PINB, &PORTB, 6}, // B6 15
{&DDRF, &PINF, &PORTF, 7}, // F7 16
{&DDRF, &PINF, &PORTF, 6}, // F6 17
{&DDRF, &PINF, &PORTF, 5}, // F5 18
{&DDRF, &PINF, &PORTF, 4}, // F4 19
{&DDRF, &PINF, &PORTF, 1}, // F1 20
{&DDRF, &PINF, &PORTF, 0}, // F0 21
{&DDRD, &PIND, &PORTD, 4}, // D4 22
{&DDRD, &PIND, &PORTD, 5}, // D5 23
{&DDRE, &PINE, &PORTE, 6} // E6 24
};
//------------------------------------------------------------------------------
#else // CORE_TEENSY
// Leonardo
static const pin_map_t pinMap[] = {
{&DDRD, &PIND, &PORTD, 2}, // D2 0
{&DDRD, &PIND, &PORTD, 3}, // D3 1
{&DDRD, &PIND, &PORTD, 1}, // D1 2
{&DDRD, &PIND, &PORTD, 0}, // D0 3
{&DDRD, &PIND, &PORTD, 4}, // D4 4
{&DDRC, &PINC, &PORTC, 6}, // C6 5
{&DDRD, &PIND, &PORTD, 7}, // D7 6
{&DDRE, &PINE, &PORTE, 6}, // E6 7
{&DDRB, &PINB, &PORTB, 4}, // B4 8
{&DDRB, &PINB, &PORTB, 5}, // B5 9
{&DDRB, &PINB, &PORTB, 6}, // B6 10
{&DDRB, &PINB, &PORTB, 7}, // B7 11
{&DDRD, &PIND, &PORTD, 6}, // D6 12
{&DDRC, &PINC, &PORTC, 7}, // C7 13
{&DDRB, &PINB, &PORTB, 3}, // B3 14
{&DDRB, &PINB, &PORTB, 1}, // B1 15
{&DDRB, &PINB, &PORTB, 2}, // B2 16
{&DDRB, &PINB, &PORTB, 0}, // B0 17
{&DDRF, &PINF, &PORTF, 7}, // F7 18
{&DDRF, &PINF, &PORTF, 6}, // F6 19
{&DDRF, &PINF, &PORTF, 5}, // F5 20
{&DDRF, &PINF, &PORTF, 4}, // F4 21
{&DDRF, &PINF, &PORTF, 1}, // F1 22
{&DDRF, &PINF, &PORTF, 0}, // F0 23
{&DDRD, &PIND, &PORTD, 4}, // D4 24
{&DDRD, &PIND, &PORTD, 7}, // D7 25
{&DDRB, &PINB, &PORTB, 4}, // B4 26
{&DDRB, &PINB, &PORTB, 5}, // B5 27
{&DDRB, &PINB, &PORTB, 6}, // B6 28
{&DDRD, &PIND, &PORTD, 6} // D6 29
};
#endif // CORE_TEENSY
//------------------------------------------------------------------------------
#elif defined(__AVR_AT90USB646__)\
|| defined(__AVR_AT90USB1286__)
// Teensy++ 1.0 & 2.0
static const pin_map_t pinMap[] = {
{&DDRD, &PIND, &PORTD, 0}, // D0 0
{&DDRD, &PIND, &PORTD, 1}, // D1 1
{&DDRD, &PIND, &PORTD, 2}, // D2 2
{&DDRD, &PIND, &PORTD, 3}, // D3 3
{&DDRD, &PIND, &PORTD, 4}, // D4 4
{&DDRD, &PIND, &PORTD, 5}, // D5 5
{&DDRD, &PIND, &PORTD, 6}, // D6 6
{&DDRD, &PIND, &PORTD, 7}, // D7 7
{&DDRE, &PINE, &PORTE, 0}, // E0 8
{&DDRE, &PINE, &PORTE, 1}, // E1 9
{&DDRC, &PINC, &PORTC, 0}, // C0 10
{&DDRC, &PINC, &PORTC, 1}, // C1 11
{&DDRC, &PINC, &PORTC, 2}, // C2 12
{&DDRC, &PINC, &PORTC, 3}, // C3 13
{&DDRC, &PINC, &PORTC, 4}, // C4 14
{&DDRC, &PINC, &PORTC, 5}, // C5 15
{&DDRC, &PINC, &PORTC, 6}, // C6 16
{&DDRC, &PINC, &PORTC, 7}, // C7 17
{&DDRE, &PINE, &PORTE, 6}, // E6 18
{&DDRE, &PINE, &PORTE, 7}, // E7 19
{&DDRB, &PINB, &PORTB, 0}, // B0 20
{&DDRB, &PINB, &PORTB, 1}, // B1 21
{&DDRB, &PINB, &PORTB, 2}, // B2 22
{&DDRB, &PINB, &PORTB, 3}, // B3 23
{&DDRB, &PINB, &PORTB, 4}, // B4 24
{&DDRB, &PINB, &PORTB, 5}, // B5 25
{&DDRB, &PINB, &PORTB, 6}, // B6 26
{&DDRB, &PINB, &PORTB, 7}, // B7 27
{&DDRA, &PINA, &PORTA, 0}, // A0 28
{&DDRA, &PINA, &PORTA, 1}, // A1 29
{&DDRA, &PINA, &PORTA, 2}, // A2 30
{&DDRA, &PINA, &PORTA, 3}, // A3 31
{&DDRA, &PINA, &PORTA, 4}, // A4 32
{&DDRA, &PINA, &PORTA, 5}, // A5 33
{&DDRA, &PINA, &PORTA, 6}, // A6 34
{&DDRA, &PINA, &PORTA, 7}, // A7 35
{&DDRE, &PINE, &PORTE, 4}, // E4 36
{&DDRE, &PINE, &PORTE, 5}, // E5 37
{&DDRF, &PINF, &PORTF, 0}, // F0 38
{&DDRF, &PINF, &PORTF, 1}, // F1 39
{&DDRF, &PINF, &PORTF, 2}, // F2 40
{&DDRF, &PINF, &PORTF, 3}, // F3 41
{&DDRF, &PINF, &PORTF, 4}, // F4 42
{&DDRF, &PINF, &PORTF, 5}, // F5 43
{&DDRF, &PINF, &PORTF, 6}, // F6 44
{&DDRF, &PINF, &PORTF, 7} // F7 45
};
//------------------------------------------------------------------------------
#else // CPU type
#error unknown CPU type
#endif // CPU type
//------------------------------------------------------------------------------
/** count of pins */
static const uint8_t digitalPinCount = sizeof(pinMap)/sizeof(pin_map_t);
//==============================================================================
/** generate bad pin number error */
void badPinNumber(void)
__attribute__((error("Pin number is too large or not a constant")));
//------------------------------------------------------------------------------
/** Check for valid pin number
* @param[in] pin Number of pin to be checked.
*/
static inline __attribute__((always_inline))
void badPinCheck(uint8_t pin) {
if (!__builtin_constant_p(pin) || pin >= digitalPinCount) {
badPinNumber();
}
}
//------------------------------------------------------------------------------
/** fast write helper
* @param[in] address I/O register address
* @param[in] bit bit number to write
* @param[in] level value for bit
*/
static inline __attribute__((always_inline))
void fastBitWriteSafe(volatile uint8_t* address, uint8_t bit, bool level) {
uint8_t oldSREG;
if (address > (uint8_t*)0X5F) {
oldSREG = SREG;
cli();
}
if (level) {
*address |= 1 << bit;
} else {
*address &= ~(1 << bit);
}
if (address > (uint8_t*)0X5F) {
SREG = oldSREG;
}
}
//------------------------------------------------------------------------------
/** read pin value
* @param[in] pin Arduino pin number
* @return value read
*/
static inline __attribute__((always_inline))
bool fastDigitalRead(uint8_t pin) {
badPinCheck(pin);
return (*pinMap[pin].pin >> pinMap[pin].bit) & 1;
}
//------------------------------------------------------------------------------
/** toggle a pin
* @param[in] pin Arduino pin number
*
* If the pin is in output mode toggle the pin level.
* If the pin is in input mode toggle the state of the 20K pullup.
*/
static inline __attribute__((always_inline))
void fastDigitalToggle(uint8_t pin) {
badPinCheck(pin);
if (pinMap[pin].pin > (uint8_t*)0X5F) {
// must write bit to high address port
*pinMap[pin].pin = 1 << pinMap[pin].bit;
} else {
// will compile to sbi and PIN register will not be read.
*pinMap[pin].pin |= 1 << pinMap[pin].bit;
}
}
//------------------------------------------------------------------------------
/** Set pin value
* @param[in] pin Arduino pin number
* @param[in] level value to write
*/
static inline __attribute__((always_inline))
void fastDigitalWrite(uint8_t pin, bool level) {
badPinCheck(pin);
fastBitWriteSafe(pinMap[pin].port, pinMap[pin].bit, level);
}
//------------------------------------------------------------------------------
/** set pin mode
* @param[in] pin Arduino pin number
* @param[in] mode if true set output mode else input mode
*
* fastPinMode does not enable or disable the 20K pullup for input mode.
*/
static inline __attribute__((always_inline))
void fastPinMode(uint8_t pin, bool mode) {
badPinCheck(pin);
fastBitWriteSafe(pinMap[pin].ddr, pinMap[pin].bit, mode);
}
#endif // __arm__
//------------------------------------------------------------------------------
/** set pin configuration
* @param[in] pin Arduino pin number
* @param[in] mode If true set output mode else input mode
* @param[in] level If mode is output, set level high/low.
* If mode is input, enable or disable the pin's 20K pullup.
*/
static inline __attribute__((always_inline))
void fastPinConfig(uint8_t pin, bool mode, bool level) {
fastPinMode(pin, mode);
fastDigitalWrite(pin, level);
}
//==============================================================================
/**
* @class DigitalPin
* @brief Fast digital port I/O
*/
template<uint8_t PinNumber>
class DigitalPin {
public:
//----------------------------------------------------------------------------
/** Constructor */
DigitalPin() {}
//----------------------------------------------------------------------------
/** Constructor
* @param[in] pinMode if true set output mode else input mode.
*/
explicit DigitalPin(bool pinMode) {
mode(pinMode);
}
//----------------------------------------------------------------------------
/** Constructor
* @param[in] mode If true set output mode else input mode
* @param[in] level If mode is output, set level high/low.
* If mode is input, enable or disable the pin's 20K pullup.
*/
DigitalPin(bool mode, bool level) {
config(mode, level);
}
//----------------------------------------------------------------------------
/** Asignment operator
* @param[in] value If true set the pin's level high else set the
* pin's level low.
*
* @return This DigitalPin instance.
*/
inline DigitalPin & operator = (bool value) __attribute__((always_inline)) {
write(value);
return *this;
}
//----------------------------------------------------------------------------
/** Parenthesis operator
* @return Pin's level
*/
inline operator bool () const __attribute__((always_inline)) {
return read();
}
//----------------------------------------------------------------------------
/** set pin configuration
* @param[in] mode If true set output mode else input mode
* @param[in] level If mode is output, set level high/low.
* If mode is input, enable or disable the pin's 20K pullup.
*/
inline __attribute__((always_inline))
void config(bool mode, bool level) {
fastPinConfig(PinNumber, mode, level);
}
//----------------------------------------------------------------------------
/**
* Set pin level high if output mode or enable 20K pullup if input mode.
*/
inline __attribute__((always_inline))
void high() {write(true);}
//----------------------------------------------------------------------------
/**
* Set pin level low if output mode or disable 20K pullup if input mode.
*/
inline __attribute__((always_inline))
void low() {write(false);}
//----------------------------------------------------------------------------
/**
* Set pin mode
* @param[in] pinMode if true set output mode else input mode.
*
* mode() does not enable or disable the 20K pullup for input mode.
*/
inline __attribute__((always_inline))
void mode(bool pinMode) {
fastPinMode(PinNumber, pinMode);
}
//----------------------------------------------------------------------------
/** @return Pin's level */
inline __attribute__((always_inline))
bool read() const {
return fastDigitalRead(PinNumber);
}
//----------------------------------------------------------------------------
/** toggle a pin
*
* If the pin is in output mode toggle the pin's level.
* If the pin is in input mode toggle the state of the 20K pullup.
*/
inline __attribute__((always_inline))
void toggle() {
fastDigitalToggle(PinNumber);
}
//----------------------------------------------------------------------------
/** Write the pin's level.
* @param[in] value If true set the pin's level high else set the
* pin's level low.
*/
inline __attribute__((always_inline))
void write(bool value) {
fastDigitalWrite(PinNumber, value);
}
};
//------------------------------------------------------------------------------
/** Nop for timing. */
#define nop asm volatile ("nop\n\t")
//------------------------------------------------------------------------------
/** Pin Mode for MISO is input.*/
const bool MISO_MODE = false;
/** Pullups disabled for MISO are disabled. */
const bool MISO_LEVEL = false;
/** Pin Mode for MOSI is output.*/
const bool MOSI_MODE = true;
/** Pin Mode for SCK is output. */
const bool SCK_MODE = true;
//------------------------------------------------------------------------------
/**
* @class SoftSPI
* @brief Fast software SPI.
*/
template<uint8_t MisoPin, uint8_t MosiPin, uint8_t SckPin, uint8_t Mode = 0>
class SoftSPI {
public:
//----------------------------------------------------------------------------
/** Initialize SoftSPI pins. */
void begin() {
fastPinConfig(MisoPin, MISO_MODE, MISO_LEVEL);
fastPinConfig(MosiPin, MOSI_MODE, !MODE_CPHA(Mode));
fastPinConfig(SckPin, SCK_MODE, MODE_CPOL(Mode));
}
//----------------------------------------------------------------------------
/** Soft SPI receive byte.
* @return Data byte received.
*/
inline __attribute__((always_inline))
uint8_t receive() {
uint8_t data = 0;
receiveBit(7, &data);
receiveBit(6, &data);
receiveBit(5, &data);
receiveBit(4, &data);
receiveBit(3, &data);
receiveBit(2, &data);
receiveBit(1, &data);
receiveBit(0, &data);
return data;
}
//----------------------------------------------------------------------------
/** Soft SPI send byte.
* @param[in] data Data byte to send.
*/
inline __attribute__((always_inline))
void send(uint8_t data) {
sendBit(7, data);
sendBit(6, data);
sendBit(5, data);
sendBit(4, data);
sendBit(3, data);
sendBit(2, data);
sendBit(1, data);
sendBit(0, data);
}
//----------------------------------------------------------------------------
/** Soft SPI transfer byte.
* @param[in] txData Data byte to send.
* @return Data byte received.
*/
inline __attribute__((always_inline))
uint8_t transfer(uint8_t txData) {
uint8_t rxData = 0;
transferBit(7, &rxData, txData);
transferBit(6, &rxData, txData);
transferBit(5, &rxData, txData);
transferBit(4, &rxData, txData);
transferBit(3, &rxData, txData);
transferBit(2, &rxData, txData);
transferBit(1, &rxData, txData);
transferBit(0, &rxData, txData);
return rxData;
}
private:
//----------------------------------------------------------------------------
inline __attribute__((always_inline))
bool MODE_CPHA(uint8_t mode) {return (mode & 1) != 0;}
inline __attribute__((always_inline))
bool MODE_CPOL(uint8_t mode) {return (mode & 2) != 0;}
inline __attribute__((always_inline))
void receiveBit(uint8_t bit, uint8_t* data) {
if (MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, !MODE_CPOL(Mode));
}
nop;
nop;
fastDigitalWrite(SckPin,
MODE_CPHA(Mode) ? MODE_CPOL(Mode) : !MODE_CPOL(Mode));
if (fastDigitalRead(MisoPin)) *data |= 1 << bit;
if (!MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, MODE_CPOL(Mode));
}
}
//----------------------------------------------------------------------------
inline __attribute__((always_inline))
void sendBit(uint8_t bit, uint8_t data) {
if (MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, !MODE_CPOL(Mode));
}
fastDigitalWrite(MosiPin, data & (1 << bit));
fastDigitalWrite(SckPin,
MODE_CPHA(Mode) ? MODE_CPOL(Mode) : !MODE_CPOL(Mode));
nop;
nop;
if (!MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, MODE_CPOL(Mode));
}
}
//----------------------------------------------------------------------------
inline __attribute__((always_inline))
void transferBit(uint8_t bit, uint8_t* rxData, uint8_t txData) {
if (MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, !MODE_CPOL(Mode));
}
fastDigitalWrite(MosiPin, txData & (1 << bit));
fastDigitalWrite(SckPin,
MODE_CPHA(Mode) ? MODE_CPOL(Mode) : !MODE_CPOL(Mode));
if (fastDigitalRead(MisoPin)) *rxData |= 1 << bit;
if (!MODE_CPHA(Mode)) {
fastDigitalWrite(SckPin, MODE_CPOL(Mode));
}
}
//----------------------------------------------------------------------------
};

68
Marlin/spi.h Normal file
View File

@ -0,0 +1,68 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#ifndef __SPI_H__
#define __SPI_H__
#include <stdint.h>
#include "softspi.h"
template<uint8_t MisoPin, uint8_t MosiPin, uint8_t SckPin>
class Spi {
static SoftSPI<MisoPin, MosiPin, SckPin> softSpi;
public:
inline __attribute__((always_inline))
static void init() {
softSpi.begin();
}
inline __attribute__((always_inline))
static void send(uint8_t data) {
softSpi.send(data);
}
inline __attribute__((always_inline))
static uint8_t receive() {
return softSpi.receive();
}
};
//hardware spi
template<>
class Spi<MISO_PIN, MOSI_PIN, SCK_PIN> {
public:
inline __attribute__((always_inline))
static void init() {
OUT_WRITE(SCK_PIN, LOW);
OUT_WRITE(MOSI_PIN, HIGH);
SET_INPUT(MISO_PIN);
WRITE(MISO_PIN, HIGH);
}
inline __attribute__((always_inline))
static uint8_t receive() {
SPDR = 0;
for (;!TEST(SPSR, SPIF););
return SPDR;
}
};
#endif

20
Marlin/temperature.cpp
View File

@ -31,6 +31,7 @@
#include "temperature.h"
#include "thermistortables.h"
#include "language.h"
#include "spi.h"
#if ENABLED(BABYSTEPPING)
#include "stepper.h"
#endif
@ -942,6 +943,15 @@ void Temperature::updateTemperaturesFromRawValues() {
#endif
#if ENABLED(HEATER_0_USES_MAX6675)
#ifndef MAX6675_SCK_PIN
#define MAX6675_SCK_PIN SCK_PIN
#endif
#ifndef MAX6675_DO_PIN
#define MAX6675_DO_PIN MISO_PIN
#endif
Spi<MAX6675_DO_PIN, MOSI_PIN, MAX6675_SCK_PIN> max6675_spi;
#endif
/**
* Initialize the temperature manager
@ -1007,11 +1017,13 @@ void Temperature::init() {
OUT_WRITE(SCK_PIN, LOW);
OUT_WRITE(MOSI_PIN, HIGH);
SET_INPUT_PULLUP(MISO_PIN);
OUT_WRITE(SS_PIN, HIGH);
max6675_spi.init();
OUT_WRITE(SS_PIN, HIGH);
OUT_WRITE(MAX6675_SS, HIGH);
#endif //HEATER_0_USES_MAX6675
#endif // HEATER_0_USES_MAX6675
#ifdef DIDR2
#define ANALOG_SELECT(pin) do{ if (pin < 8) SBI(DIDR0, pin); else SBI(DIDR2, pin - 8); }while(0)
@ -1356,9 +1368,7 @@ void Temperature::disable_all_heaters() {
// Read a big-endian temperature value
max6675_temp = 0;
for (uint8_t i = sizeof(max6675_temp); i--;) {
SPDR = 0;
for (;!TEST(SPSR, SPIF););
max6675_temp |= SPDR;
max6675_temp |= max6675_spi.receive();
if (i > 0) max6675_temp <<= 8; // shift left if not the last byte
}

2
Marlin/ultralcd.cpp
View File

@ -1564,9 +1564,9 @@ void kill_screen(const char* lcd_msg) {
*/
void _lcd_level_bed_homing() {
if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_HOMING), NULL);
lcdDrawUpdate = LCDVIEW_KEEP_REDRAWING;
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
lcd_goto_screen(_lcd_level_bed_homing_done);
lcdDrawUpdate = LCDVIEW_KEEP_REDRAWING;
}
/**