Fix case light logic on Azteeg_X3 boards.

This commit is contained in:
Bob-the-Kuhn 2017-06-01 12:33:24 -05:00
parent 155aa62fb0
commit 9a9bbfc57c
3 changed files with 14 additions and 19 deletions

View File

@ -32,11 +32,10 @@
#error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_NAME "Azteeg X3"
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
#define CASE_LIGHT_PIN 6 // must define it here or else RAMPS will define it
#endif
#define BOARD_NAME "Azteeg X3"
#include "pins_RAMPS_13.h"
@ -75,10 +74,8 @@
//
// Misc
//
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) && STAT_LED_RED_PIN == 6
#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT) && PIN_EXISTS(STAT_LED_RED) && STAT_LED_RED_PIN == CASE_LIGHT_PIN
#undef STAT_LED_RED_PIN
#undef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN 6 // open collector FET driver
#endif
//
@ -94,6 +91,7 @@
#if SERVO0_PIN == 7
#undef SERVO0_PIN
#def SERVO0_PIN 11
#endif
#define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 21

View File

@ -28,12 +28,13 @@
#error "Azteeg X3 Pro supports up to 5 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_NAME "Azteeg X3 Pro"
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
#define CASE_LIGHT_PIN 44 // must define it here or else RAMPS will define it
#endif
#define BOARD_NAME "Azteeg X3 Pro"
#include "pins_RAMPS.h"
#ifndef __AVR_ATmega2560__
@ -144,19 +145,16 @@
//
// Misc. Functions
//
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT)
#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT) && defined(DOGLCD_A0) && DOGLCD_A0 == CASE_LIGHT_PIN
#undef DOGLCD_A0 // steal pin 44 for the case light; if you have a Viki2 and have connected it
#define DOGLCD_A0 57 // following the Panucatt wiring diagram, you may need to tweak these pin assignments
// as the wiring diagram uses pin 44 for DOGLCD_A0
#undef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN 44 // must have a hardware PWM
// as the wiring diagram uses pin 44 for DOGLCD_A0
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3pro board
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN

View File

@ -204,8 +204,7 @@
#define PS_ON_PIN 12
#if !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#undef CASE_LIGHT_PIN
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
#define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \