commit
b373826428
1
Documentation/changelog.md
Normal file
1
Documentation/changelog.md
Normal file
@ -0,0 +1 @@
|
|||||||
|
|
@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
|
|||||||
// The following define selects which electronics board you have.
|
// The following define selects which electronics board you have.
|
||||||
// Please choose the name from boards.h that matches your setup
|
// Please choose the name from boards.h that matches your setup
|
||||||
#ifndef MOTHERBOARD
|
#ifndef MOTHERBOARD
|
||||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
#define MOTHERBOARD BOARD_RAMPS_13_EFB
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Define this to set a custom name for your generic Mendel,
|
// Define this to set a custom name for your generic Mendel,
|
||||||
@ -123,8 +123,8 @@ Here are some standard links for getting your machine calibrated:
|
|||||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||||
|
|
||||||
#define TEMP_SENSOR_0 -1
|
#define TEMP_SENSOR_0 1
|
||||||
#define TEMP_SENSOR_1 -1
|
#define TEMP_SENSOR_1 0
|
||||||
#define TEMP_SENSOR_2 0
|
#define TEMP_SENSOR_2 0
|
||||||
#define TEMP_SENSOR_3 0
|
#define TEMP_SENSOR_3 0
|
||||||
#define TEMP_SENSOR_BED 0
|
#define TEMP_SENSOR_BED 0
|
||||||
@ -301,35 +301,21 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||||||
// Enable this option for Toshiba steppers
|
// Enable this option for Toshiba steppers
|
||||||
// #define CONFIG_STEPPERS_TOSHIBA
|
// #define CONFIG_STEPPERS_TOSHIBA
|
||||||
|
|
||||||
// coarse Endstop Settings
|
// The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
|
||||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
#define ENDSTOPPULLUP_XMAX
|
||||||
|
#define ENDSTOPPULLUP_YMAX
|
||||||
|
#define ENDSTOPPULLUP_ZMAX
|
||||||
|
#define ENDSTOPPULLUP_XMIN
|
||||||
|
#define ENDSTOPPULLUP_YMIN
|
||||||
|
#define ENDSTOPPULLUP_ZMIN
|
||||||
|
|
||||||
#ifndef ENDSTOPPULLUPS
|
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_XMAX
|
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_YMAX
|
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_ZMAX
|
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_XMIN
|
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_YMIN
|
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||||
// #define ENDSTOPPULLUP_ZMIN
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#ifdef ENDSTOPPULLUPS
|
|
||||||
#define ENDSTOPPULLUP_XMAX
|
|
||||||
#define ENDSTOPPULLUP_YMAX
|
|
||||||
#define ENDSTOPPULLUP_ZMAX
|
|
||||||
#define ENDSTOPPULLUP_XMIN
|
|
||||||
#define ENDSTOPPULLUP_YMIN
|
|
||||||
#define ENDSTOPPULLUP_ZMIN
|
|
||||||
#endif
|
|
||||||
|
|
||||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
|
||||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
|
||||||
//#define DISABLE_MAX_ENDSTOPS
|
//#define DISABLE_MAX_ENDSTOPS
|
||||||
//#define DISABLE_MIN_ENDSTOPS
|
//#define DISABLE_MIN_ENDSTOPS
|
||||||
|
|
||||||
@ -346,13 +332,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DISABLE_E false // For all extruders
|
#define DISABLE_E false // For all extruders
|
||||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||||
|
|
||||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
// If you motor turns to wrong direction, you can invert it here:
|
||||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
#define INVERT_X_DIR false
|
||||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
#define INVERT_Y_DIR false
|
||||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
#define INVERT_Z_DIR false
|
||||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
#define INVERT_E0_DIR false
|
||||||
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
#define INVERT_E1_DIR false
|
||||||
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
#define INVERT_E2_DIR false
|
||||||
|
#define INVERT_E3_DIR false
|
||||||
|
|
||||||
// ENDSTOP SETTINGS:
|
// ENDSTOP SETTINGS:
|
||||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||||
@ -364,9 +351,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||||
|
|
||||||
// Travel limits after homing (units are in mm)
|
// Travel limits after homing (units are in mm)
|
||||||
#define X_MAX_POS 205
|
#define X_MAX_POS 200
|
||||||
#define X_MIN_POS 0
|
#define X_MIN_POS 0
|
||||||
#define Y_MAX_POS 205
|
#define Y_MAX_POS 200
|
||||||
#define Y_MIN_POS 0
|
#define Y_MIN_POS 0
|
||||||
#define Z_MAX_POS 200
|
#define Z_MAX_POS 200
|
||||||
#define Z_MIN_POS 0
|
#define Z_MIN_POS 0
|
||||||
@ -416,6 +403,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define RIGHT_PROBE_BED_POSITION 170
|
#define RIGHT_PROBE_BED_POSITION 170
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
@ -438,8 +427,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
|
|
||||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||||
// X and Y offsets must be integers
|
// X and Y offsets must be integers
|
||||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right
|
||||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind
|
||||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||||
|
|
||||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||||
@ -450,6 +439,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
||||||
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
||||||
|
|
||||||
|
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||||
|
//Useful to retract a deployable probe.
|
||||||
|
|
||||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
@ -497,12 +489,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
|
|
||||||
// default settings
|
// default settings
|
||||||
|
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
@ -543,11 +536,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
// Preheat Constants
|
// Preheat Constants
|
||||||
#define PLA_PREHEAT_HOTEND_TEMP 180
|
#define PLA_PREHEAT_HOTEND_TEMP 180
|
||||||
#define PLA_PREHEAT_HPB_TEMP 70
|
#define PLA_PREHEAT_HPB_TEMP 70
|
||||||
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||||
|
|
||||||
#define ABS_PREHEAT_HOTEND_TEMP 240
|
#define ABS_PREHEAT_HOTEND_TEMP 240
|
||||||
#define ABS_PREHEAT_HPB_TEMP 100
|
#define ABS_PREHEAT_HPB_TEMP 110
|
||||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||||
|
|
||||||
//==============================LCD and SD support=============================
|
//==============================LCD and SD support=============================
|
||||||
|
|
||||||
|
@ -3,7 +3,7 @@
|
|||||||
*
|
*
|
||||||
* Configuration and EEPROM storage
|
* Configuration and EEPROM storage
|
||||||
*
|
*
|
||||||
* V15 EEPROM Layout:
|
* V16 EEPROM Layout:
|
||||||
*
|
*
|
||||||
* ver
|
* ver
|
||||||
* axis_steps_per_unit (x4)
|
* axis_steps_per_unit (x4)
|
||||||
@ -11,6 +11,7 @@
|
|||||||
* max_acceleration_units_per_sq_second (x4)
|
* max_acceleration_units_per_sq_second (x4)
|
||||||
* acceleration
|
* acceleration
|
||||||
* retract_acceleration
|
* retract_acceleration
|
||||||
|
* travel_aceeleration
|
||||||
* minimumfeedrate
|
* minimumfeedrate
|
||||||
* mintravelfeedrate
|
* mintravelfeedrate
|
||||||
* minsegmenttime
|
* minsegmenttime
|
||||||
@ -104,7 +105,7 @@ void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) {
|
|||||||
// wrong data being written to the variables.
|
// wrong data being written to the variables.
|
||||||
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
|
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
|
||||||
|
|
||||||
#define EEPROM_VERSION "V15"
|
#define EEPROM_VERSION "V16"
|
||||||
|
|
||||||
#ifdef EEPROM_SETTINGS
|
#ifdef EEPROM_SETTINGS
|
||||||
|
|
||||||
@ -118,6 +119,7 @@ void Config_StoreSettings() {
|
|||||||
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
|
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
|
||||||
EEPROM_WRITE_VAR(i, acceleration);
|
EEPROM_WRITE_VAR(i, acceleration);
|
||||||
EEPROM_WRITE_VAR(i, retract_acceleration);
|
EEPROM_WRITE_VAR(i, retract_acceleration);
|
||||||
|
EEPROM_WRITE_VAR(i, travel_acceleration);
|
||||||
EEPROM_WRITE_VAR(i, minimumfeedrate);
|
EEPROM_WRITE_VAR(i, minimumfeedrate);
|
||||||
EEPROM_WRITE_VAR(i, mintravelfeedrate);
|
EEPROM_WRITE_VAR(i, mintravelfeedrate);
|
||||||
EEPROM_WRITE_VAR(i, minsegmenttime);
|
EEPROM_WRITE_VAR(i, minsegmenttime);
|
||||||
@ -253,6 +255,7 @@ void Config_RetrieveSettings() {
|
|||||||
|
|
||||||
EEPROM_READ_VAR(i, acceleration);
|
EEPROM_READ_VAR(i, acceleration);
|
||||||
EEPROM_READ_VAR(i, retract_acceleration);
|
EEPROM_READ_VAR(i, retract_acceleration);
|
||||||
|
EEPROM_READ_VAR(i, travel_acceleration);
|
||||||
EEPROM_READ_VAR(i, minimumfeedrate);
|
EEPROM_READ_VAR(i, minimumfeedrate);
|
||||||
EEPROM_READ_VAR(i, mintravelfeedrate);
|
EEPROM_READ_VAR(i, mintravelfeedrate);
|
||||||
EEPROM_READ_VAR(i, minsegmenttime);
|
EEPROM_READ_VAR(i, minsegmenttime);
|
||||||
@ -380,6 +383,7 @@ void Config_ResetDefault() {
|
|||||||
|
|
||||||
acceleration = DEFAULT_ACCELERATION;
|
acceleration = DEFAULT_ACCELERATION;
|
||||||
retract_acceleration = DEFAULT_RETRACT_ACCELERATION;
|
retract_acceleration = DEFAULT_RETRACT_ACCELERATION;
|
||||||
|
travel_acceleration = DEFAULT_TRAVEL_ACCELERATION;
|
||||||
minimumfeedrate = DEFAULT_MINIMUMFEEDRATE;
|
minimumfeedrate = DEFAULT_MINIMUMFEEDRATE;
|
||||||
minsegmenttime = DEFAULT_MINSEGMENTTIME;
|
minsegmenttime = DEFAULT_MINSEGMENTTIME;
|
||||||
mintravelfeedrate = DEFAULT_MINTRAVELFEEDRATE;
|
mintravelfeedrate = DEFAULT_MINTRAVELFEEDRATE;
|
||||||
@ -516,11 +520,12 @@ void Config_PrintSettings(bool forReplay) {
|
|||||||
SERIAL_EOL;
|
SERIAL_EOL;
|
||||||
SERIAL_ECHO_START;
|
SERIAL_ECHO_START;
|
||||||
if (!forReplay) {
|
if (!forReplay) {
|
||||||
SERIAL_ECHOLNPGM("Acceleration: S=acceleration, T=retract acceleration");
|
SERIAL_ECHOLNPGM("Accelerations: P=printing, R=retract and T=travel");
|
||||||
SERIAL_ECHO_START;
|
SERIAL_ECHO_START;
|
||||||
}
|
}
|
||||||
SERIAL_ECHOPAIR(" M204 S", acceleration );
|
SERIAL_ECHOPAIR(" M204 P", acceleration );
|
||||||
SERIAL_ECHOPAIR(" T", retract_acceleration);
|
SERIAL_ECHOPAIR(" R", retract_acceleration);
|
||||||
|
SERIAL_ECHOPAIR(" T", travel_acceleration);
|
||||||
SERIAL_EOL;
|
SERIAL_EOL;
|
||||||
|
|
||||||
SERIAL_ECHO_START;
|
SERIAL_ECHO_START;
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 2
|
#define Z_HOME_RETRACT_MM 2
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -201,6 +201,10 @@
|
|||||||
#endif
|
#endif
|
||||||
|
|
||||||
float homing_feedrate[] = HOMING_FEEDRATE;
|
float homing_feedrate[] = HOMING_FEEDRATE;
|
||||||
|
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||||
|
int xy_travel_speed = XY_TRAVEL_SPEED;
|
||||||
|
#endif
|
||||||
|
int homing_bump_divisor[] = HOMING_BUMP_DIVISOR;
|
||||||
bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
|
bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
|
||||||
int feedmultiply = 100; //100->1 200->2
|
int feedmultiply = 100; //100->1 200->2
|
||||||
int saved_feedmultiply;
|
int saved_feedmultiply;
|
||||||
@ -780,7 +784,7 @@ void get_command()
|
|||||||
while(cmdbuffer[bufindw][count] != '*') checksum = checksum^cmdbuffer[bufindw][count++];
|
while(cmdbuffer[bufindw][count] != '*') checksum = checksum^cmdbuffer[bufindw][count++];
|
||||||
strchr_pointer = strchr(cmdbuffer[bufindw], '*');
|
strchr_pointer = strchr(cmdbuffer[bufindw], '*');
|
||||||
|
|
||||||
if( (int)(strtod(strchr_pointer + 1, NULL)) != checksum) {
|
if(strtol(strchr_pointer + 1, NULL, 10) != checksum) {
|
||||||
SERIAL_ERROR_START;
|
SERIAL_ERROR_START;
|
||||||
SERIAL_ERRORPGM(MSG_ERR_CHECKSUM_MISMATCH);
|
SERIAL_ERRORPGM(MSG_ERR_CHECKSUM_MISMATCH);
|
||||||
SERIAL_ERRORLN(gcode_LastN);
|
SERIAL_ERRORLN(gcode_LastN);
|
||||||
@ -816,7 +820,7 @@ void get_command()
|
|||||||
}
|
}
|
||||||
if((strchr(cmdbuffer[bufindw], 'G') != NULL)){
|
if((strchr(cmdbuffer[bufindw], 'G') != NULL)){
|
||||||
strchr_pointer = strchr(cmdbuffer[bufindw], 'G');
|
strchr_pointer = strchr(cmdbuffer[bufindw], 'G');
|
||||||
switch((int)((strtod(strchr_pointer + 1, NULL)))){
|
switch(strtol(strchr_pointer + 1, NULL, 10)){
|
||||||
case 0:
|
case 0:
|
||||||
case 1:
|
case 1:
|
||||||
case 2:
|
case 2:
|
||||||
@ -1146,7 +1150,18 @@ static void run_z_probe() {
|
|||||||
st_synchronize();
|
st_synchronize();
|
||||||
|
|
||||||
// move back down slowly to find bed
|
// move back down slowly to find bed
|
||||||
feedrate = homing_feedrate[Z_AXIS]/4;
|
|
||||||
|
if (homing_bump_divisor[Z_AXIS] >= 1)
|
||||||
|
{
|
||||||
|
feedrate = homing_feedrate[Z_AXIS]/homing_bump_divisor[Z_AXIS];
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
feedrate = homing_feedrate[Z_AXIS]/10;
|
||||||
|
SERIAL_ECHOLN("Warning: The Homing Bump Feedrate Divisor cannot be less then 1");
|
||||||
|
}
|
||||||
|
|
||||||
|
|
||||||
zPosition -= home_retract_mm(Z_AXIS) * 2;
|
zPosition -= home_retract_mm(Z_AXIS) * 2;
|
||||||
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], zPosition, current_position[E_AXIS], feedrate/60, active_extruder);
|
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], zPosition, current_position[E_AXIS], feedrate/60, active_extruder);
|
||||||
st_synchronize();
|
st_synchronize();
|
||||||
@ -1165,7 +1180,7 @@ static void do_blocking_move_to(float x, float y, float z) {
|
|||||||
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate/60, active_extruder);
|
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate/60, active_extruder);
|
||||||
st_synchronize();
|
st_synchronize();
|
||||||
|
|
||||||
feedrate = XY_TRAVEL_SPEED;
|
feedrate = xy_travel_speed;
|
||||||
|
|
||||||
current_position[X_AXIS] = x;
|
current_position[X_AXIS] = x;
|
||||||
current_position[Y_AXIS] = y;
|
current_position[Y_AXIS] = y;
|
||||||
@ -1308,11 +1323,17 @@ static void homeaxis(int axis) {
|
|||||||
st_synchronize();
|
st_synchronize();
|
||||||
|
|
||||||
destination[axis] = 2*home_retract_mm(axis) * axis_home_dir;
|
destination[axis] = 2*home_retract_mm(axis) * axis_home_dir;
|
||||||
#ifdef DELTA
|
|
||||||
feedrate = homing_feedrate[axis]/10;
|
if (homing_bump_divisor[axis] >= 1)
|
||||||
#else
|
{
|
||||||
feedrate = homing_feedrate[axis]/2 ;
|
feedrate = homing_feedrate[axis]/homing_bump_divisor[axis];
|
||||||
#endif
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
feedrate = homing_feedrate[axis]/10;
|
||||||
|
SERIAL_ECHOLN("Warning: The Homing Bump Feedrate Divisor cannot be less then 1");
|
||||||
|
}
|
||||||
|
|
||||||
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
|
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
|
||||||
st_synchronize();
|
st_synchronize();
|
||||||
#ifdef DELTA
|
#ifdef DELTA
|
||||||
@ -1771,41 +1792,32 @@ inline void gcode_G28() {
|
|||||||
|
|
||||||
#ifdef AUTO_BED_LEVELING_GRID
|
#ifdef AUTO_BED_LEVELING_GRID
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 20 // The probe square sides can be no smaller than this
|
|
||||||
|
|
||||||
// Make sure probing points are reachable
|
// Make sure probing points are reachable
|
||||||
|
|
||||||
#if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
|
#if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
|
||||||
#error The given LEFT_PROBE_BED_POSITION can't be reached by the probe.
|
#error "The given LEFT_PROBE_BED_POSITION can't be reached by the probe."
|
||||||
#elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
|
#elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
|
||||||
#error The given RIGHT_PROBE_BED_POSITION can't be reached by the probe.
|
#error "The given RIGHT_PROBE_BED_POSITION can't be reached by the probe."
|
||||||
#elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
|
#elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
|
||||||
#error The given FRONT_PROBE_BED_POSITION can't be reached by the probe.
|
#error "The given FRONT_PROBE_BED_POSITION can't be reached by the probe."
|
||||||
#elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
|
#elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
|
||||||
#error The given BACK_PROBE_BED_POSITION can't be reached by the probe.
|
#error "The given BACK_PROBE_BED_POSITION can't be reached by the probe."
|
||||||
|
|
||||||
// Check if Probe_Offset * Grid Points is greater than Probing Range
|
|
||||||
|
|
||||||
#elif abs(X_PROBE_OFFSET_FROM_EXTRUDER) * (AUTO_BED_LEVELING_GRID_POINTS-1) >= RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION
|
|
||||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
||||||
#elif abs(Y_PROBE_OFFSET_FROM_EXTRUDER) * (AUTO_BED_LEVELING_GRID_POINTS-1) >= BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION
|
|
||||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#else // !AUTO_BED_LEVELING_GRID
|
#else // !AUTO_BED_LEVELING_GRID
|
||||||
|
|
||||||
#if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
|
#if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
|
||||||
#error The given ABL_PROBE_PT_1_X can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_1_X can't be reached by the probe."
|
||||||
#elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
|
#elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
|
||||||
#error The given ABL_PROBE_PT_2_X can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_2_X can't be reached by the probe."
|
||||||
#elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
|
#elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
|
||||||
#error The given ABL_PROBE_PT_3_X can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_3_X can't be reached by the probe."
|
||||||
#elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
|
#elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
|
||||||
#error The given ABL_PROBE_PT_1_Y can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_1_Y can't be reached by the probe."
|
||||||
#elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
|
#elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
|
||||||
#error The given ABL_PROBE_PT_2_Y can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_2_Y can't be reached by the probe."
|
||||||
#elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
|
#elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
|
||||||
#error The given ABL_PROBE_PT_3_Y can't be reached by the probe.
|
#error "The given ABL_PROBE_PT_3_Y can't be reached by the probe."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#endif // !AUTO_BED_LEVELING_GRID
|
#endif // !AUTO_BED_LEVELING_GRID
|
||||||
@ -1821,6 +1833,8 @@ inline void gcode_G28() {
|
|||||||
* P Set the size of the grid that will be probed (P x P points).
|
* P Set the size of the grid that will be probed (P x P points).
|
||||||
* Example: "G29 P4"
|
* Example: "G29 P4"
|
||||||
*
|
*
|
||||||
|
* S Set the XY travel speed between probe points (in mm/min)
|
||||||
|
*
|
||||||
* V Set the verbose level (0-4). Example: "G29 V3"
|
* V Set the verbose level (0-4). Example: "G29 V3"
|
||||||
*
|
*
|
||||||
* T Generate a Bed Topology Report. Example: "G29 P5 T" for a detailed report.
|
* T Generate a Bed Topology Report. Example: "G29 P5 T" for a detailed report.
|
||||||
@ -1877,11 +1891,13 @@ inline void gcode_G28() {
|
|||||||
SERIAL_PROTOCOLPGM("G29 Auto Bed Leveling\n");
|
SERIAL_PROTOCOLPGM("G29 Auto Bed Leveling\n");
|
||||||
|
|
||||||
int auto_bed_leveling_grid_points = code_seen('P') ? code_value_long() : AUTO_BED_LEVELING_GRID_POINTS;
|
int auto_bed_leveling_grid_points = code_seen('P') ? code_value_long() : AUTO_BED_LEVELING_GRID_POINTS;
|
||||||
if (auto_bed_leveling_grid_points < 2 || auto_bed_leveling_grid_points > AUTO_BED_LEVELING_GRID_POINTS) {
|
if (auto_bed_leveling_grid_points < 2) {
|
||||||
SERIAL_PROTOCOLPGM("?Number of probed (P)oints is implausible (2 minimum).\n");
|
SERIAL_PROTOCOLPGM("?Number of probed (P)oints is implausible (2 minimum).\n");
|
||||||
return;
|
return;
|
||||||
}
|
}
|
||||||
|
|
||||||
|
xy_travel_speed = code_seen('S') ? code_value_long() : XY_TRAVEL_SPEED;
|
||||||
|
|
||||||
int left_probe_bed_position = code_seen('L') ? code_value_long() : LEFT_PROBE_BED_POSITION,
|
int left_probe_bed_position = code_seen('L') ? code_value_long() : LEFT_PROBE_BED_POSITION,
|
||||||
right_probe_bed_position = code_seen('R') ? code_value_long() : RIGHT_PROBE_BED_POSITION,
|
right_probe_bed_position = code_seen('R') ? code_value_long() : RIGHT_PROBE_BED_POSITION,
|
||||||
front_probe_bed_position = code_seen('F') ? code_value_long() : FRONT_PROBE_BED_POSITION,
|
front_probe_bed_position = code_seen('F') ? code_value_long() : FRONT_PROBE_BED_POSITION,
|
||||||
@ -2110,6 +2126,11 @@ inline void gcode_G28() {
|
|||||||
#ifdef Z_PROBE_SLED
|
#ifdef Z_PROBE_SLED
|
||||||
dock_sled(true, -SLED_DOCKING_OFFSET); // dock the probe, correcting for over-travel
|
dock_sled(true, -SLED_DOCKING_OFFSET); // dock the probe, correcting for over-travel
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
#ifdef Z_PROBE_END_SCRIPT
|
||||||
|
enquecommands_P(PSTR(Z_PROBE_END_SCRIPT));
|
||||||
|
st_synchronize();
|
||||||
|
#endif
|
||||||
}
|
}
|
||||||
|
|
||||||
#ifndef Z_PROBE_SLED
|
#ifndef Z_PROBE_SLED
|
||||||
@ -3257,16 +3278,34 @@ inline void gcode_M203() {
|
|||||||
}
|
}
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* M204: Set Default Acceleration and/or Default Filament Acceleration in mm/sec^2 (M204 S3000 T7000)
|
* M204: Set Accelerations in mm/sec^2 (M204 P1200 R3000 T3000)
|
||||||
*
|
*
|
||||||
* S = normal moves
|
* P = Printing moves
|
||||||
* T = filament only moves
|
* R = Retract only (no X, Y, Z) moves
|
||||||
|
* T = Travel (non printing) moves
|
||||||
*
|
*
|
||||||
* Also sets minimum segment time in ms (B20000) to prevent buffer under-runs and M20 minimum feedrate
|
* Also sets minimum segment time in ms (B20000) to prevent buffer under-runs and M20 minimum feedrate
|
||||||
*/
|
*/
|
||||||
inline void gcode_M204() {
|
inline void gcode_M204() {
|
||||||
if (code_seen('S')) acceleration = code_value();
|
if (code_seen('P'))
|
||||||
if (code_seen('T')) retract_acceleration = code_value();
|
{
|
||||||
|
acceleration = code_value();
|
||||||
|
SERIAL_ECHOPAIR("Setting Printing Acceleration: ", acceleration );
|
||||||
|
SERIAL_EOL;
|
||||||
|
}
|
||||||
|
if (code_seen('R'))
|
||||||
|
{
|
||||||
|
retract_acceleration = code_value();
|
||||||
|
SERIAL_ECHOPAIR("Setting Retract Acceleration: ", retract_acceleration );
|
||||||
|
SERIAL_EOL;
|
||||||
|
}
|
||||||
|
if (code_seen('T'))
|
||||||
|
{
|
||||||
|
travel_acceleration = code_value();
|
||||||
|
SERIAL_ECHOPAIR("Setting Travel Acceleration: ", travel_acceleration );
|
||||||
|
SERIAL_EOL;
|
||||||
|
}
|
||||||
|
|
||||||
}
|
}
|
||||||
|
|
||||||
/**
|
/**
|
||||||
@ -4218,7 +4257,7 @@ inline void gcode_M350() {
|
|||||||
*/
|
*/
|
||||||
inline void gcode_M351() {
|
inline void gcode_M351() {
|
||||||
#if defined(X_MS1_PIN) && X_MS1_PIN > -1
|
#if defined(X_MS1_PIN) && X_MS1_PIN > -1
|
||||||
if (code_seen('S')) switch((int)code_value()) {
|
if (code_seen('S')) switch(code_value_long()) {
|
||||||
case 1:
|
case 1:
|
||||||
for(int i=0;i<NUM_AXIS;i++) if (code_seen(axis_codes[i])) microstep_ms(i, code_value(), -1);
|
for(int i=0;i<NUM_AXIS;i++) if (code_seen(axis_codes[i])) microstep_ms(i, code_value(), -1);
|
||||||
if (code_seen('B')) microstep_ms(4, code_value(), -1);
|
if (code_seen('B')) microstep_ms(4, code_value(), -1);
|
||||||
@ -4417,7 +4456,7 @@ void process_commands() {
|
|||||||
}
|
}
|
||||||
|
|
||||||
else if (code_seen('M')) {
|
else if (code_seen('M')) {
|
||||||
switch( (int)code_value() ) {
|
switch( code_value_long() ) {
|
||||||
#ifdef ULTIPANEL
|
#ifdef ULTIPANEL
|
||||||
case 0: // M0 - Unconditional stop - Wait for user button press on LCD
|
case 0: // M0 - Unconditional stop - Wait for user button press on LCD
|
||||||
case 1: // M1 - Conditional stop - Wait for user button press on LCD
|
case 1: // M1 - Conditional stop - Wait for user button press on LCD
|
||||||
|
@ -413,6 +413,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define RIGHT_PROBE_BED_POSITION 170
|
#define RIGHT_PROBE_BED_POSITION 170
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
@ -498,8 +500,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {250, 250, 3.3, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {250, 250, 3.3, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 2
|
#define Z_HOME_RETRACT_MM 2
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -419,6 +419,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||||
@ -503,8 +505,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 500} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 500} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 3
|
#define Z_HOME_RETRACT_MM 3
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -443,6 +443,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||||
@ -528,8 +530,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {300, 300, 30, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {300, 300, 30, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {300,300,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {300,300,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 400 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 2000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 3
|
#define X_HOME_RETRACT_MM 3
|
||||||
#define Y_HOME_RETRACT_MM 3
|
#define Y_HOME_RETRACT_MM 3
|
||||||
#define Z_HOME_RETRACT_MM 3
|
#define Z_HOME_RETRACT_MM 3
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
#ifdef SCARA
|
#ifdef SCARA
|
||||||
#define QUICK_HOME //SCARA needs Quickhome
|
#define QUICK_HOME //SCARA needs Quickhome
|
||||||
|
@ -413,6 +413,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||||
@ -497,8 +499,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {350, 350, 7.2, 80} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {350, 350, 7.2, 80} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {1000,1000,10,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {1000,1000,10,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 2
|
#define Z_HOME_RETRACT_MM 2
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -440,8 +440,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
|
#define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
|
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
|
@ -411,6 +411,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||||
@ -495,8 +497,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 2
|
#define Z_HOME_RETRACT_MM 2
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -412,6 +412,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define RIGHT_PROBE_BED_POSITION 170
|
#define RIGHT_PROBE_BED_POSITION 170
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
|
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||||
|
|
||||||
// Set the number of grid points per dimension
|
// Set the number of grid points per dimension
|
||||||
// You probably don't need more than 3 (squared=9)
|
// You probably don't need more than 3 (squared=9)
|
||||||
@ -501,8 +503,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
/* MICHEL: This has an impact on the "ripples" in print walls */
|
/* MICHEL: This has an impact on the "ripples" in print walls */
|
||||||
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
@ -214,6 +214,7 @@
|
|||||||
#define X_HOME_RETRACT_MM 5
|
#define X_HOME_RETRACT_MM 5
|
||||||
#define Y_HOME_RETRACT_MM 5
|
#define Y_HOME_RETRACT_MM 5
|
||||||
#define Z_HOME_RETRACT_MM 1
|
#define Z_HOME_RETRACT_MM 1
|
||||||
|
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||||
|
|
||||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||||
|
@ -233,6 +233,9 @@
|
|||||||
#ifndef MSG_A_RETRACT
|
#ifndef MSG_A_RETRACT
|
||||||
#define MSG_A_RETRACT "A-retract"
|
#define MSG_A_RETRACT "A-retract"
|
||||||
#endif
|
#endif
|
||||||
|
#ifndef MSG_A_TRAVEL
|
||||||
|
#define MSG_A_TRAVEL "A-travel"
|
||||||
|
#endif
|
||||||
#ifndef MSG_XSTEPS
|
#ifndef MSG_XSTEPS
|
||||||
#define MSG_XSTEPS "Xsteps/mm"
|
#define MSG_XSTEPS "Xsteps/mm"
|
||||||
#endif
|
#endif
|
||||||
|
@ -67,8 +67,9 @@ float max_feedrate[NUM_AXIS]; // set the max speeds
|
|||||||
float axis_steps_per_unit[NUM_AXIS];
|
float axis_steps_per_unit[NUM_AXIS];
|
||||||
unsigned long max_acceleration_units_per_sq_second[NUM_AXIS]; // Use M201 to override by software
|
unsigned long max_acceleration_units_per_sq_second[NUM_AXIS]; // Use M201 to override by software
|
||||||
float minimumfeedrate;
|
float minimumfeedrate;
|
||||||
float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
|
float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all printing moves. M204 SXXXX
|
||||||
float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
||||||
|
float travel_acceleration; // Travel acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX
|
||||||
float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
||||||
float max_z_jerk;
|
float max_z_jerk;
|
||||||
float max_e_jerk;
|
float max_e_jerk;
|
||||||
@ -907,19 +908,24 @@ Having the real displacement of the head, we can calculate the total movement le
|
|||||||
{
|
{
|
||||||
block->acceleration_st = ceil(retract_acceleration * steps_per_mm); // convert to: acceleration steps/sec^2
|
block->acceleration_st = ceil(retract_acceleration * steps_per_mm); // convert to: acceleration steps/sec^2
|
||||||
}
|
}
|
||||||
|
else if(block->steps_e == 0)
|
||||||
|
{
|
||||||
|
block->acceleration_st = ceil(travel_acceleration * steps_per_mm); // convert to: acceleration steps/sec^2
|
||||||
|
}
|
||||||
else
|
else
|
||||||
{
|
{
|
||||||
block->acceleration_st = ceil(acceleration * steps_per_mm); // convert to: acceleration steps/sec^2
|
block->acceleration_st = ceil(acceleration * steps_per_mm); // convert to: acceleration steps/sec^2
|
||||||
// Limit acceleration per axis
|
|
||||||
if(((float)block->acceleration_st * (float)block->steps_x / (float)block->step_event_count) > axis_steps_per_sqr_second[X_AXIS])
|
|
||||||
block->acceleration_st = axis_steps_per_sqr_second[X_AXIS];
|
|
||||||
if(((float)block->acceleration_st * (float)block->steps_y / (float)block->step_event_count) > axis_steps_per_sqr_second[Y_AXIS])
|
|
||||||
block->acceleration_st = axis_steps_per_sqr_second[Y_AXIS];
|
|
||||||
if(((float)block->acceleration_st * (float)block->steps_e / (float)block->step_event_count) > axis_steps_per_sqr_second[E_AXIS])
|
|
||||||
block->acceleration_st = axis_steps_per_sqr_second[E_AXIS];
|
|
||||||
if(((float)block->acceleration_st * (float)block->steps_z / (float)block->step_event_count ) > axis_steps_per_sqr_second[Z_AXIS])
|
|
||||||
block->acceleration_st = axis_steps_per_sqr_second[Z_AXIS];
|
|
||||||
}
|
}
|
||||||
|
// Limit acceleration per axis
|
||||||
|
if(((float)block->acceleration_st * (float)block->steps_x / (float)block->step_event_count) > axis_steps_per_sqr_second[X_AXIS])
|
||||||
|
block->acceleration_st = axis_steps_per_sqr_second[X_AXIS];
|
||||||
|
if(((float)block->acceleration_st * (float)block->steps_y / (float)block->step_event_count) > axis_steps_per_sqr_second[Y_AXIS])
|
||||||
|
block->acceleration_st = axis_steps_per_sqr_second[Y_AXIS];
|
||||||
|
if(((float)block->acceleration_st * (float)block->steps_e / (float)block->step_event_count) > axis_steps_per_sqr_second[E_AXIS])
|
||||||
|
block->acceleration_st = axis_steps_per_sqr_second[E_AXIS];
|
||||||
|
if(((float)block->acceleration_st * (float)block->steps_z / (float)block->step_event_count ) > axis_steps_per_sqr_second[Z_AXIS])
|
||||||
|
block->acceleration_st = axis_steps_per_sqr_second[Z_AXIS];
|
||||||
|
|
||||||
block->acceleration = block->acceleration_st / steps_per_mm;
|
block->acceleration = block->acceleration_st / steps_per_mm;
|
||||||
block->acceleration_rate = (long)((float)block->acceleration_st * (16777216.0 / (F_CPU / 8.0)));
|
block->acceleration_rate = (long)((float)block->acceleration_st * (16777216.0 / (F_CPU / 8.0)));
|
||||||
|
|
||||||
|
@ -112,6 +112,7 @@ extern unsigned long max_acceleration_units_per_sq_second[NUM_AXIS]; // Use M201
|
|||||||
extern float minimumfeedrate;
|
extern float minimumfeedrate;
|
||||||
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
|
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
|
||||||
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
||||||
|
extern float travel_acceleration; // Travel acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX
|
||||||
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
|
||||||
extern float max_z_jerk;
|
extern float max_z_jerk;
|
||||||
extern float max_e_jerk;
|
extern float max_e_jerk;
|
||||||
|
@ -903,6 +903,7 @@ static void lcd_control_motion_menu() {
|
|||||||
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_Z, &max_acceleration_units_per_sq_second[Z_AXIS], 100, 99000, reset_acceleration_rates);
|
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_Z, &max_acceleration_units_per_sq_second[Z_AXIS], 100, 99000, reset_acceleration_rates);
|
||||||
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E, &max_acceleration_units_per_sq_second[E_AXIS], 100, 99000, reset_acceleration_rates);
|
MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E, &max_acceleration_units_per_sq_second[E_AXIS], 100, 99000, reset_acceleration_rates);
|
||||||
MENU_ITEM_EDIT(float5, MSG_A_RETRACT, &retract_acceleration, 100, 99000);
|
MENU_ITEM_EDIT(float5, MSG_A_RETRACT, &retract_acceleration, 100, 99000);
|
||||||
|
MENU_ITEM_EDIT(float5, MSG_A_TRAVEL, &travel_acceleration, 100, 99000);
|
||||||
MENU_ITEM_EDIT(float52, MSG_XSTEPS, &axis_steps_per_unit[X_AXIS], 5, 9999);
|
MENU_ITEM_EDIT(float52, MSG_XSTEPS, &axis_steps_per_unit[X_AXIS], 5, 9999);
|
||||||
MENU_ITEM_EDIT(float52, MSG_YSTEPS, &axis_steps_per_unit[Y_AXIS], 5, 9999);
|
MENU_ITEM_EDIT(float52, MSG_YSTEPS, &axis_steps_per_unit[Y_AXIS], 5, 9999);
|
||||||
MENU_ITEM_EDIT(float51, MSG_ZSTEPS, &axis_steps_per_unit[Z_AXIS], 5, 9999);
|
MENU_ITEM_EDIT(float51, MSG_ZSTEPS, &axis_steps_per_unit[Z_AXIS], 5, 9999);
|
||||||
|
@ -27,11 +27,11 @@ We are actively looking for testers. So please try the current development versi
|
|||||||
[![Coverity Scan Build Status](https://scan.coverity.com/projects/2224/badge.svg)](https://scan.coverity.com/projects/2224)
|
[![Coverity Scan Build Status](https://scan.coverity.com/projects/2224/badge.svg)](https://scan.coverity.com/projects/2224)
|
||||||
[![Travis Build Status](https://travis-ci.org/MarlinFirmware/Marlin.svg)](https://travis-ci.org/MarlinFirmware/Marlin)
|
[![Travis Build Status](https://travis-ci.org/MarlinFirmware/Marlin.svg)](https://travis-ci.org/MarlinFirmware/Marlin)
|
||||||
|
|
||||||
What bugs are we working on: [Bug Fixing Round 2](https://github.com/MarlinFirmware/Marlin/milestones/Bug%20Fixing%20Round%202)
|
What bugs are we working on: [Bug Fixing Round 3](https://github.com/MarlinFirmware/Marlin/milestones/Bug%20Fixing%20Round%203)
|
||||||
|
|
||||||
## Contact
|
## Contact
|
||||||
|
|
||||||
__IRC:__ #marlin-firmware @freenode ([WebChat Client](https://webchat.freenode.net/?channels=marlin-firmware), [Archive](http://energymonitor-dk.dns4e.net/marlin-firmware-log/))
|
__IRC:__ #marlin-firmware @freenode ([WebChat Client](https://webchat.freenode.net/?channels=marlin-firmware)
|
||||||
|
|
||||||
__Mailing List:__ marlin@lists.0l.de ([Subscribe](http://lists.0l.de/mailman/listinfo/marlin), [Archive](http://lists.0l.de/pipermail/marlin/))
|
__Mailing List:__ marlin@lists.0l.de ([Subscribe](http://lists.0l.de/mailman/listinfo/marlin), [Archive](http://lists.0l.de/pipermail/marlin/))
|
||||||
|
|
||||||
|
Loading…
Reference in New Issue
Block a user