BIBO2 default update and Cyclops config (#10107)
This commit is contained in:
parent
7b2ea8febe
commit
c2ba9a03ee
@ -306,7 +306,7 @@
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_4 0
|
||||
#define TEMP_SENSOR_BED 60
|
||||
#define TEMP_SENSOR_BED 5
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
@ -433,8 +433,8 @@
|
||||
// It also enables the M302 command to set the minimum extrusion temperature
|
||||
// or to allow moving the extruder regardless of the hotend temperature.
|
||||
// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
|
||||
#define PREVENT_COLD_EXTRUSION
|
||||
#define EXTRUDE_MINTEMP 170
|
||||
//#define PREVENT_COLD_EXTRUSION
|
||||
//#define EXTRUDE_MINTEMP 170
|
||||
|
||||
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
|
||||
// Note that for Bowden Extruders a too-small value here may prevent loading.
|
||||
@ -485,11 +485,11 @@
|
||||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||||
//#define USE_XMIN_PLUG
|
||||
//#define USE_YMIN_PLUG
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
#define USE_XMAX_PLUG
|
||||
#define USE_YMAX_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
// Enable pullup for all endstops to prevent a floating state
|
||||
@ -543,14 +543,14 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 93.6}
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 400}
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 350, 350, 10, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 350, 350, 10, 50 }
|
||||
|
||||
/**
|
||||
* Default Max Acceleration (change/s) change = mm/s
|
||||
@ -558,7 +558,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 300, 5000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 300, 2500 }
|
||||
|
||||
/**
|
||||
* Default Acceleration (change/s) change = mm/s
|
||||
@ -705,7 +705,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
#define MIN_PROBE_EDGE 10
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
#define XY_PROBE_SPEED 9000
|
||||
|
||||
// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||||
@ -733,7 +733,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
//#define Z_AFTER_PROBING 10 // Z position after probing is done
|
||||
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
@ -766,8 +766,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// Enable this option for Toshiba stepper drivers
|
||||
@ -788,27 +788,27 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR 1
|
||||
#define Y_HOME_DIR 1
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
// @section machine
|
||||
|
||||
// The size of the print bed
|
||||
#define X_BED_SIZE 214
|
||||
#define X_BED_SIZE 220
|
||||
#define Y_BED_SIZE 186
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS -107
|
||||
#define Y_MIN_POS -93
|
||||
#define X_MIN_POS -13
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS 141
|
||||
#define Y_MAX_POS 93
|
||||
#define X_MAX_POS 250
|
||||
#define Y_MAX_POS 186
|
||||
#define Z_MAX_POS 186
|
||||
|
||||
/**
|
||||
@ -1066,8 +1066,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
#endif
|
||||
|
||||
// Homing speeds (mm/m)
|
||||
#define HOMING_FEEDRATE_XY (15*60)
|
||||
#define HOMING_FEEDRATE_Z (4*60)
|
||||
#define HOMING_FEEDRATE_XY (25*60)
|
||||
#define HOMING_FEEDRATE_Z (6*60)
|
||||
|
||||
// @section calibrate
|
||||
|
||||
@ -1172,12 +1172,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
// @section temperature
|
||||
|
||||
// Preheat Constants
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_BED 60
|
||||
#define PREHEAT_1_TEMP_HOTEND 190
|
||||
#define PREHEAT_1_TEMP_BED 65
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 80
|
||||
#define PREHEAT_2_TEMP_BED 100
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
|
File diff suppressed because it is too large
Load Diff
Loading…
Reference in New Issue
Block a user