Sanity check parity with 2.0.x

Marlin/SanityCheck.h

@@ -26,6 +26,9 @@
  * Test configuration values for errors at compile-time.
  */
 
+#ifndef _SANITYCHECK_H_
+#define _SANITYCHECK_H_
+
 /**
  * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features.
  */
@@ -254,7 +257,19 @@
 /**
  * Serial
  */
-#if defined(USBCON) && ENABLED(SERIAL_XON_XOFF)
+#ifndef USBCON
+  #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
+    #error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops."
+  #endif
+
+  #if RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE))
+    #error "RX_BUFFER_SIZE must be a power of 2 greater than 1."
+  #endif
+
+  #if TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE))
+    #error "TX_BUFFER_SIZE must be 0, a power of 2 greater than 1, and no greater than 256."
+  #endif
+#elif ENABLED(SERIAL_XON_XOFF)
   #error "SERIAL_XON_XOFF is not supported on USB-native AVR devices."
 #endif
 
@@ -355,9 +370,7 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
  * Babystepping
  */
 #if ENABLED(BABYSTEPPING)
-  #if DISABLED(ULTRA_LCD) && DISABLED(I2C_POSITION_ENCODERS)
+  #if ENABLED(SCARA)
-    #error "BABYSTEPPING requires an LCD controller."
-  #elif ENABLED(SCARA)
     #error "BABYSTEPPING is not implemented for SCARA yet."
   #elif ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
     #error "BABYSTEPPING only implemented for Z axis on deltabots."
@@ -595,7 +608,7 @@ static_assert(1 >= 0
   #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED
     #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
   #elif ENABLED(DELTA_AUTO_CALIBRATION) && !(HAS_BED_PROBE || ENABLED(ULTIPANEL))
-    #error "DELTA_AUTO_CALIBRATION requires either a probe or an LCD Controller."
+    #error "DELTA_AUTO_CALIBRATION requires a probe or LCD Controller."
   #elif ABL_GRID
     #if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0
       #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers."
@@ -989,11 +1002,12 @@ static_assert(1 >= 0
   #error "TEMP_SENSOR_0 is required."
 #endif
 
-#if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
+// Pins are required for heaters
-  #if !HAS_HEATER_1
+#if ENABLED(HEATER_0_USES_MAX6675) && !(defined(MAX6675_SS) && MAX6675_SS >= 0)
+  #error "MAX6675_SS (required for TEMP_SENSOR_0) not defined for this board."
+#elif (HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)) && !HAS_HEATER_1
   #error "HEATER_1_PIN not defined for this board."
 #endif
-#endif
 
 #if HOTENDS > 1
   #if TEMP_SENSOR_1 == 0
@@ -1412,8 +1426,8 @@ static_assert(1 >= 0
 /**
  * Make sure HAVE_TMC2130 is warranted
  */
-#if ENABLED(HAVE_TMC2130) && !( \
+#if ENABLED(HAVE_TMC2130)
-       ENABLED(  X_IS_TMC2130 ) \
+  #if !( ENABLED(  X_IS_TMC2130 ) \
       || ENABLED( X2_IS_TMC2130 ) \
       || ENABLED(  Y_IS_TMC2130 ) \
       || ENABLED( Y2_IS_TMC2130 ) \
@@ -1425,11 +1439,12 @@ static_assert(1 >= 0
       || ENABLED( E3_IS_TMC2130 ) \
       || ENABLED( E4_IS_TMC2130 ) )
     #error "HAVE_TMC2130 requires at least one TMC2130 stepper to be set."
-#elif ENABLED(SENSORLESS_HOMING) && DISABLED(HAVE_TMC2130)
+  #elif ENABLED(HYBRID_THRESHOLD) && DISABLED(STEALTHCHOP)
-  #error "Enable HAVE_TMC2130 to use SENSORLESS_HOMING."
+    #error "Enable STEALTHCHOP to use HYBRID_THRESHOLD."
   #elif defined(AUTOMATIC_CURRENT_CONTROL)
     #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
   #endif
+#endif
 
 /**
  * Make sure HAVE_TMC2208 is warranted
@@ -1581,3 +1596,5 @@ static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too m
     #endif
   #endif
 #endif
+
+#endif // _SANITYCHECK_H_