Move setup() and loop() to the end

This commit is contained in:
Scott Lahteine 2016-09-11 20:21:54 -05:00
parent 8ff338c2b9
commit f9a192c7e3

View File

@ -850,10 +850,6 @@ void servo_init() {
*/ */
STOW_Z_SERVO(); STOW_Z_SERVO();
#endif #endif
#if HAS_BED_PROBE
endstops.enable_z_probe(false);
#endif
} }
/** /**
@ -879,216 +875,6 @@ void servo_init() {
#endif #endif
/**
* Marlin entry-point: Set up before the program loop
* - Set up the kill pin, filament runout, power hold
* - Start the serial port
* - Print startup messages and diagnostics
* - Get EEPROM or default settings
* - Initialize managers for:
* temperature
* planner
* watchdog
* stepper
* photo pin
* servos
* LCD controller
* Digipot I2C
* Z probe sled
* status LEDs
*/
void setup() {
#ifdef DISABLE_JTAG
// Disable JTAG on AT90USB chips to free up pins for IO
MCUCR = 0x80;
MCUCR = 0x80;
#endif
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
setup_filrunoutpin();
#endif
setup_killpin();
setup_powerhold();
#if HAS_STEPPER_RESET
disableStepperDrivers();
#endif
MYSERIAL.begin(BAUDRATE);
SERIAL_PROTOCOLLNPGM("start");
SERIAL_ECHO_START;
// Check startup - does nothing if bootloader sets MCUSR to 0
byte mcu = MCUSR;
if (mcu & 1) SERIAL_ECHOLNPGM(MSG_POWERUP);
if (mcu & 2) SERIAL_ECHOLNPGM(MSG_EXTERNAL_RESET);
if (mcu & 4) SERIAL_ECHOLNPGM(MSG_BROWNOUT_RESET);
if (mcu & 8) SERIAL_ECHOLNPGM(MSG_WATCHDOG_RESET);
if (mcu & 32) SERIAL_ECHOLNPGM(MSG_SOFTWARE_RESET);
MCUSR = 0;
SERIAL_ECHOPGM(MSG_MARLIN);
SERIAL_ECHOLNPGM(" " SHORT_BUILD_VERSION);
#ifdef STRING_DISTRIBUTION_DATE
#ifdef STRING_CONFIG_H_AUTHOR
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_CONFIGURATION_VER);
SERIAL_ECHOPGM(STRING_DISTRIBUTION_DATE);
SERIAL_ECHOPGM(MSG_AUTHOR);
SERIAL_ECHOLNPGM(STRING_CONFIG_H_AUTHOR);
SERIAL_ECHOPGM("Compiled: ");
SERIAL_ECHOLNPGM(__DATE__);
#endif // STRING_CONFIG_H_AUTHOR
#endif // STRING_DISTRIBUTION_DATE
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_FREE_MEMORY);
SERIAL_ECHO(freeMemory());
SERIAL_ECHOPGM(MSG_PLANNER_BUFFER_BYTES);
SERIAL_ECHOLN((int)sizeof(block_t)*BLOCK_BUFFER_SIZE);
// Send "ok" after commands by default
for (int8_t i = 0; i < BUFSIZE; i++) send_ok[i] = true;
// Load data from EEPROM if available (or use defaults)
// This also updates variables in the planner, elsewhere
Config_RetrieveSettings();
// Initialize current position based on home_offset
memcpy(current_position, home_offset, sizeof(home_offset));
// Vital to init stepper/planner equivalent for current_position
SYNC_PLAN_POSITION_KINEMATIC();
thermalManager.init(); // Initialize temperature loop
#if ENABLED(USE_WATCHDOG)
watchdog_init();
#endif
stepper.init(); // Initialize stepper, this enables interrupts!
setup_photpin();
servo_init();
#if HAS_CONTROLLERFAN
SET_OUTPUT(CONTROLLERFAN_PIN); //Set pin used for driver cooling fan
#endif
#if HAS_STEPPER_RESET
enableStepperDrivers();
#endif
#if ENABLED(DIGIPOT_I2C)
digipot_i2c_init();
#endif
#if ENABLED(DAC_STEPPER_CURRENT)
dac_init();
#endif
#if ENABLED(Z_PROBE_SLED) && PIN_EXISTS(SLED)
pinMode(SLED_PIN, OUTPUT);
digitalWrite(SLED_PIN, LOW); // turn it off
#endif // Z_PROBE_SLED
setup_homepin();
#ifdef STAT_LED_RED
pinMode(STAT_LED_RED, OUTPUT);
digitalWrite(STAT_LED_RED, LOW); // turn it off
#endif
#ifdef STAT_LED_BLUE
pinMode(STAT_LED_BLUE, OUTPUT);
digitalWrite(STAT_LED_BLUE, LOW); // turn it off
#endif
lcd_init();
#if ENABLED(SHOW_BOOTSCREEN)
#if ENABLED(DOGLCD)
safe_delay(BOOTSCREEN_TIMEOUT);
#elif ENABLED(ULTRA_LCD)
bootscreen();
lcd_init();
#endif
#endif
#if ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1
// Initialize mixing to 100% color 1
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
mixing_factor[i] = (i == 0) ? 1 : 0;
for (uint8_t t = 0; t < MIXING_VIRTUAL_TOOLS; t++)
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
mixing_virtual_tool_mix[t][i] = mixing_factor[i];
#endif
#if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
i2c.onReceive(i2c_on_receive);
i2c.onRequest(i2c_on_request);
#endif
}
/**
* The main Marlin program loop
*
* - Save or log commands to SD
* - Process available commands (if not saving)
* - Call heater manager
* - Call inactivity manager
* - Call endstop manager
* - Call LCD update
*/
void loop() {
if (commands_in_queue < BUFSIZE) get_available_commands();
#if ENABLED(SDSUPPORT)
card.checkautostart(false);
#endif
if (commands_in_queue) {
#if ENABLED(SDSUPPORT)
if (card.saving) {
char* command = command_queue[cmd_queue_index_r];
if (strstr_P(command, PSTR("M29"))) {
// M29 closes the file
card.closefile();
SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED);
ok_to_send();
}
else {
// Write the string from the read buffer to SD
card.write_command(command);
if (card.logging)
process_next_command(); // The card is saving because it's logging
else
ok_to_send();
}
}
else
process_next_command();
#else
process_next_command();
#endif // SDSUPPORT
// The queue may be reset by a command handler or by code invoked by idle() within a handler
if (commands_in_queue) {
--commands_in_queue;
cmd_queue_index_r = (cmd_queue_index_r + 1) % BUFSIZE;
}
}
endstops.report_state();
idle();
}
void gcode_line_error(const char* err, bool doFlush = true) { void gcode_line_error(const char* err, bool doFlush = true) {
SERIAL_ERROR_START; SERIAL_ERROR_START;
serialprintPGM(err); serialprintPGM(err);
@ -8889,3 +8675,217 @@ void calculate_volumetric_multipliers() {
for (uint8_t i = 0; i < COUNT(filament_size); i++) for (uint8_t i = 0; i < COUNT(filament_size); i++)
volumetric_multiplier[i] = calculate_volumetric_multiplier(filament_size[i]); volumetric_multiplier[i] = calculate_volumetric_multiplier(filament_size[i]);
} }
/**
* Marlin entry-point: Set up before the program loop
* - Set up the kill pin, filament runout, power hold
* - Start the serial port
* - Print startup messages and diagnostics
* - Get EEPROM or default settings
* - Initialize managers for:
* temperature
* planner
* watchdog
* stepper
* photo pin
* servos
* LCD controller
* Digipot I2C
* Z probe sled
* status LEDs
*/
void setup() {
#ifdef DISABLE_JTAG
// Disable JTAG on AT90USB chips to free up pins for IO
MCUCR = 0x80;
MCUCR = 0x80;
#endif
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
setup_filrunoutpin();
#endif
setup_killpin();
setup_powerhold();
#if HAS_STEPPER_RESET
disableStepperDrivers();
#endif
MYSERIAL.begin(BAUDRATE);
SERIAL_PROTOCOLLNPGM("start");
SERIAL_ECHO_START;
// Check startup - does nothing if bootloader sets MCUSR to 0
byte mcu = MCUSR;
if (mcu & 1) SERIAL_ECHOLNPGM(MSG_POWERUP);
if (mcu & 2) SERIAL_ECHOLNPGM(MSG_EXTERNAL_RESET);
if (mcu & 4) SERIAL_ECHOLNPGM(MSG_BROWNOUT_RESET);
if (mcu & 8) SERIAL_ECHOLNPGM(MSG_WATCHDOG_RESET);
if (mcu & 32) SERIAL_ECHOLNPGM(MSG_SOFTWARE_RESET);
MCUSR = 0;
SERIAL_ECHOPGM(MSG_MARLIN);
SERIAL_ECHOLNPGM(" " SHORT_BUILD_VERSION);
#ifdef STRING_DISTRIBUTION_DATE
#ifdef STRING_CONFIG_H_AUTHOR
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_CONFIGURATION_VER);
SERIAL_ECHOPGM(STRING_DISTRIBUTION_DATE);
SERIAL_ECHOPGM(MSG_AUTHOR);
SERIAL_ECHOLNPGM(STRING_CONFIG_H_AUTHOR);
SERIAL_ECHOPGM("Compiled: ");
SERIAL_ECHOLNPGM(__DATE__);
#endif // STRING_CONFIG_H_AUTHOR
#endif // STRING_DISTRIBUTION_DATE
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_FREE_MEMORY);
SERIAL_ECHO(freeMemory());
SERIAL_ECHOPGM(MSG_PLANNER_BUFFER_BYTES);
SERIAL_ECHOLN((int)sizeof(block_t)*BLOCK_BUFFER_SIZE);
// Send "ok" after commands by default
for (int8_t i = 0; i < BUFSIZE; i++) send_ok[i] = true;
// Load data from EEPROM if available (or use defaults)
// This also updates variables in the planner, elsewhere
Config_RetrieveSettings();
// Initialize current position based on home_offset
memcpy(current_position, home_offset, sizeof(home_offset));
// Vital to init stepper/planner equivalent for current_position
SYNC_PLAN_POSITION_KINEMATIC();
thermalManager.init(); // Initialize temperature loop
#if ENABLED(USE_WATCHDOG)
watchdog_init();
#endif
stepper.init(); // Initialize stepper, this enables interrupts!
setup_photpin();
servo_init();
#if HAS_BED_PROBE
endstops.enable_z_probe(false);
#endif
#if HAS_CONTROLLERFAN
SET_OUTPUT(CONTROLLERFAN_PIN); //Set pin used for driver cooling fan
#endif
#if HAS_STEPPER_RESET
enableStepperDrivers();
#endif
#if ENABLED(DIGIPOT_I2C)
digipot_i2c_init();
#endif
#if ENABLED(DAC_STEPPER_CURRENT)
dac_init();
#endif
#if ENABLED(Z_PROBE_SLED) && PIN_EXISTS(SLED)
pinMode(SLED_PIN, OUTPUT);
digitalWrite(SLED_PIN, LOW); // turn it off
#endif // Z_PROBE_SLED
setup_homepin();
#ifdef STAT_LED_RED
pinMode(STAT_LED_RED, OUTPUT);
digitalWrite(STAT_LED_RED, LOW); // turn it off
#endif
#ifdef STAT_LED_BLUE
pinMode(STAT_LED_BLUE, OUTPUT);
digitalWrite(STAT_LED_BLUE, LOW); // turn it off
#endif
lcd_init();
#if ENABLED(SHOW_BOOTSCREEN)
#if ENABLED(DOGLCD)
safe_delay(BOOTSCREEN_TIMEOUT);
#elif ENABLED(ULTRA_LCD)
bootscreen();
lcd_init();
#endif
#endif
#if ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1
// Initialize mixing to 100% color 1
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
mixing_factor[i] = (i == 0) ? 1 : 0;
for (uint8_t t = 0; t < MIXING_VIRTUAL_TOOLS; t++)
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
mixing_virtual_tool_mix[t][i] = mixing_factor[i];
#endif
#if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
i2c.onReceive(i2c_on_receive);
i2c.onRequest(i2c_on_request);
#endif
}
/**
* The main Marlin program loop
*
* - Save or log commands to SD
* - Process available commands (if not saving)
* - Call heater manager
* - Call inactivity manager
* - Call endstop manager
* - Call LCD update
*/
void loop() {
if (commands_in_queue < BUFSIZE) get_available_commands();
#if ENABLED(SDSUPPORT)
card.checkautostart(false);
#endif
if (commands_in_queue) {
#if ENABLED(SDSUPPORT)
if (card.saving) {
char* command = command_queue[cmd_queue_index_r];
if (strstr_P(command, PSTR("M29"))) {
// M29 closes the file
card.closefile();
SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED);
ok_to_send();
}
else {
// Write the string from the read buffer to SD
card.write_command(command);
if (card.logging)
process_next_command(); // The card is saving because it's logging
else
ok_to_send();
}
}
else
process_next_command();
#else
process_next_command();
#endif // SDSUPPORT
// The queue may be reset by a command handler or by code invoked by idle() within a handler
if (commands_in_queue) {
--commands_in_queue;
cmd_queue_index_r = (cmd_queue_index_r + 1) % BUFSIZE;
}
}
endstops.report_state();
idle();
}