diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp
index 4839e3ed3..e064ebaf7 100644
--- a/Marlin/configuration_store.cpp
+++ b/Marlin/configuration_store.cpp
@@ -341,10 +341,6 @@ void MarlinSettings::postprocess() {
 
   bool MarlinSettings::eeprom_error, MarlinSettings::validating;
 
-  #if ENABLED(AUTO_BED_LEVELING_UBL)
-    int16_t MarlinSettings::meshes_begin;
-  #endif
-
   void MarlinSettings::write_data(int &pos, const uint8_t *value, uint16_t size, uint16_t *crc) {
     if (eeprom_error) { pos += size; return; }
     while (size--) {
@@ -1364,9 +1360,6 @@ void MarlinSettings::postprocess() {
       }
 
       #if ENABLED(AUTO_BED_LEVELING_UBL)
-        meshes_begin = (eeprom_index + 32) & 0xFFF8;  // Pad the end of configuration data so it
-                                                      // can float up or down a little bit without
-                                                      // disrupting the mesh data
         ubl.report_state();
 
         if (!validating) {
@@ -1434,12 +1427,13 @@ void MarlinSettings::postprocess() {
       }
     #endif
 
+    int16_t MarlinSettings::meshes_start_index() {
+      return (datasize() + EEPROM_OFFSET + 32) & 0xFFF8;  // Pad the end of configuration data so it can float up
+                                                          // or down a little bit without disrupting the mesh data
+    }
+
     uint16_t MarlinSettings::calc_num_meshes() {
-      //obviously this will get more sophisticated once we've added an actual MAT
-
-      if (meshes_begin <= 0) return 0;
-
-      return (meshes_end - meshes_begin) / sizeof(ubl.z_values);
+      return (meshes_end - meshes_start_index()) / sizeof(ubl.z_values);
     }
 
     void MarlinSettings::store_mesh(const int8_t slot) {
diff --git a/Marlin/configuration_store.h b/Marlin/configuration_store.h
index 55cfb1fb1..54102807b 100644
--- a/Marlin/configuration_store.h
+++ b/Marlin/configuration_store.h
@@ -38,13 +38,10 @@ class MarlinSettings {
       bool success = true;
       reset();
       #if ENABLED(EEPROM_SETTINGS)
-        if ((success = save())) {
-          #if ENABLED(AUTO_BED_LEVELING_UBL)
-            success = load(); // UBL uses load() to know the end of EEPROM
-          #elif ENABLED(EEPROM_CHITCHAT)
-            report();
-          #endif
-        }
+        success = save();
+        #if ENABLED(EEPROM_CHITCHAT)
+          if (success) report();
+        #endif
       #endif
       return success;
     }
@@ -55,8 +52,8 @@ class MarlinSettings {
 
       #if ENABLED(AUTO_BED_LEVELING_UBL) // Eventually make these available if any leveling system
                                          // That can store is enabled
-        FORCE_INLINE static int16_t get_start_of_meshes() { return meshes_begin; }
-        FORCE_INLINE static int16_t get_end_of_meshes() { return meshes_end; }
+        static int16_t meshes_start_index();
+        FORCE_INLINE static int16_t meshes_end_index() { return meshes_end; }
         static uint16_t calc_num_meshes();
         static void store_mesh(const int8_t slot);
         static void load_mesh(const int8_t slot, void * const into=NULL);
diff --git a/Marlin/ubl_G29.cpp b/Marlin/ubl_G29.cpp
index e741e391d..e1b00b475 100644
--- a/Marlin/ubl_G29.cpp
+++ b/Marlin/ubl_G29.cpp
@@ -308,12 +308,6 @@
 
   void unified_bed_leveling::G29() {
 
-    if (!settings.calc_num_meshes()) {
-      SERIAL_PROTOCOLLNPGM("?Enable EEPROM and init with");
-      SERIAL_PROTOCOLLNPGM("M502, M500, M501 in that order.\n");
-      return;
-    }
-
     if (g29_parameter_parsing()) return; // abort if parsing the simple parameters causes a problem,
 
     // Check for commands that require the printer to be homed
@@ -1273,8 +1267,8 @@
       SERIAL_EOL();
       safe_delay(50);
 
-      SERIAL_PROTOCOLPAIR("Meshes go from ", hex_address((void*)settings.get_start_of_meshes()));
-      SERIAL_PROTOCOLLNPAIR(" to ", hex_address((void*)settings.get_end_of_meshes()));
+      SERIAL_PROTOCOLPAIR("Meshes go from ", hex_address((void*)settings.meshes_start_index()));
+      SERIAL_PROTOCOLLNPAIR(" to ", hex_address((void*)settings.meshes_end_index()));
       safe_delay(50);
 
       SERIAL_PROTOCOLLNPAIR("sizeof(ubl) :  ", (int)sizeof(ubl));
@@ -1283,7 +1277,7 @@
       SERIAL_EOL();
       safe_delay(25);
 
-      SERIAL_PROTOCOLLNPAIR("EEPROM free for UBL: ", hex_address((void*)(settings.get_end_of_meshes() - settings.get_start_of_meshes())));
+      SERIAL_PROTOCOLLNPAIR("EEPROM free for UBL: ", hex_address((void*)(settings.meshes_end_index() - settings.meshes_start_index())));
       safe_delay(50);
 
       SERIAL_PROTOCOLPAIR("EEPROM can hold ", settings.calc_num_meshes());
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index 1abf8ec25..a66003d31 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -2303,7 +2303,6 @@ void kill_screen(const char* lcd_msg) {
       MENU_BACK(MSG_UBL_LEVEL_BED);
       if (!WITHIN(ubl_storage_slot, 0, a - 1)) {
         STATIC_ITEM(MSG_NO_STORAGE);
-        STATIC_ITEM(MSG_INIT_EEPROM);
       }
       else {
         MENU_ITEM_EDIT(int3, MSG_UBL_STORAGE_SLOT, &ubl_storage_slot, 0, a - 1);