diff --git a/Documentation/GCodes.md b/Documentation/GCodes.md index e69de29bb..dd582946e 100644 --- a/Documentation/GCodes.md +++ b/Documentation/GCodes.md @@ -0,0 +1,103 @@ +# Implemented G Codes + +## G Codes + +* G0 -> G1 +* G1 - Coordinated Movement X Y Z E +* G2 - CW ARC +* G3 - CCW ARC +* G4 - Dwell S or P +* G10 - retract filament according to settings of M207 +* G11 - retract recover filament according to settings of M208 +* G28 - Home all Axis +* G29 - Detailed Z-Probe, probes the bed at 3 points. You must de at the home position for this to work correctly. +* G30 - Single Z Probe, probes bed at current XY location. +* G31 - Dock Z Probe sled (if enabled) +* G32 - Undock Z Probe sled (if enabled) +* G90 - Use Absolute Coordinates +* G91 - Use Relative Coordinates +* G92 - Set current position to cordinates given + +## M Codes +* M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled) +* M1 - Same as M0 +* M17 - Enable/Power all stepper motors +* M18 - Disable all stepper motors; same as M84 +* M20 - List SD card +* M21 - Init SD card +* M22 - Release SD card +* M23 - Select SD file (M23 filename.g) +* M24 - Start/resume SD print +* M25 - Pause SD print +* M26 - Set SD position in bytes (M26 S12345) +* M27 - Report SD print status +* M28 - Start SD write (M28 filename.g) +* M29 - Stop SD write +* M30 - Delete file from SD (M30 filename.g) +* M31 - Output time since last M109 or SD card start to serial +* M32 - Select file and start SD print (Can be used when printing from SD card) +* M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used. +* M80 - Turn on Power Supply +* M81 - Turn off Power Supply +* M82 - Set E codes absolute (default) +* M83 - Set E codes relative while in Absolute Coordinates (G90) mode +* M84 - Disable steppers until next move, or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. +* M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) +* M92 - Set axis_steps_per_unit - same syntax as G92 +* M104 - Set extruder target temp +* M105 - Read current temp +* M106 - Fan on +* M107 - Fan off +* M109 - Sxxx Wait for extruder current temp to reach target temp. Waits only when heating +* Rxxx Wait for extruder current temp to reach target temp. Waits when heating and cooling +* M112 - Emergency stop +* M114 - Output current position to serial port +* M115 - Capabilities string +* M117 - display message +* M119 - Output Endstop status to serial port +* M126 - Solenoid Air Valve Open (BariCUDA support by jmil) +* M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil) +* M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) +* M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) +* M140 - Set bed target temp +* M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating +* Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling +* M200 D- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters). +* M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) +* M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! +* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec +* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate +* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk +* M206 - set additional homeing offset +* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting +* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min] +* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. +* M218 - set hotend offset (in mm): T X Y +* M220 S- set speed factor override percentage +* M221 S- set extrude factor override percentage +* M240 - Trigger a camera to take a photograph +* M280 - Position an RC Servo P S, ommit S to report back current angle +* M300 - Play beepsound S P +* M301 - Set PID parameters P I and D +* M302 - Allow cold extrudes +* M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) +* M304 - Set bed PID parameters P I and D +* M400 - Finish all moves +* M401 - Lower z-probe if present +* M402 - Raise z-probe if present +* M404 - N Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters +* M405 - Turn on Filament Sensor extrusion control. Optional D to set delay in centimeters between sensor and extruder +* M406 - Turn off Filament Sensor extrusion control +* M407 - Displays measured filament diameter +* M500 - stores paramters in EEPROM +* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +* M503 - print the current settings (from memory not from eeprom) +* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) +* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] +* M907 - Set digital trimpot motor current using axis codes. +* M908 - Control digital trimpot directly. +* M350 - Set microstepping mode. +* M351 - Toggle MS1 MS2 pins directly. +* M928 - Start SD logging (M928 filename.g) - ended by M29 +* M999 - Restart after being stopped by error