d8331d97d6
Unify M91x parameter I meaning, simplify reports
2018-07-11 20:31:40 -05:00
5cddfce0ee
Endstops::report_state => event_handler
2018-07-11 19:47:25 -05:00
5f587126b9
Loosen static assertion guarding overflow in SCAN_THERMISTOR_TABLE ( #11240 )
...
Bisect search merged in #10882 actually works fine for thermistor
tables with up to 255 entries with no overflow, due to C++ integer
promotion rules.
Closes issue #11220 .
2018-07-11 16:42:23 -05:00
39b3e4c501
Support for multiple Max7219 units in a chain ( #11226 )
...
* Support for multiple Max7219 units in a chain
I'll move this support over to bugfix_2.0.0 in the next few days. And
then look at updating the Max7219_idle() routine to make use of multiple
units in a chain.
* spelling correction
2018-07-08 17:35:58 -05:00
fae2929b6b
Resolve issue where user can't edit mesh
2018-07-08 14:39:08 -05:00
ccb225f43a
Float maths updates for 2.0.x parity ( #11213 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-07-06 21:44:33 -05:00
fc9f4ce2c0
Fix missing quote in language list
...
Co-Authored-By: p3p <p3p@p3psoft.co.uk>
2018-07-04 13:40:18 -05:00
a69cc6c5ba
Fix Trigorilla include typo
2018-07-03 20:22:36 -05:00
03a704600c
No M914 or SGT set for non-sensorless axes ( #11197 )
2018-07-03 20:10:43 -05:00
e84341412c
Merge pull request #11194 from Schullebernd/bugfix-1.1.x
...
[1.1.x] Tronxy X3A configurations and thermistor
2018-07-03 19:05:51 -05:00
fae20983eb
Add configurations for Tronxy X3A
2018-07-03 18:14:46 -05:00
559e935785
Bring default Configuration.h up to date
2018-07-03 18:10:55 -05:00
432da42dba
Add thermistor 501 (100K Zonestar)
2018-07-03 18:10:55 -05:00
0702c78e62
Fix and improve POWER_LOSS_RECOVERY ( #11186 )
2018-07-02 23:21:18 -05:00
84187dca5c
Add "Marlin Dev Mode" option
2018-07-02 22:53:01 -05:00
b7c648db32
Minor patches for POWER_LOSS_RECOVERY
2018-07-02 17:25:15 -05:00
a83f7f1d25
Turn off DISABLE_INACTIVE_EXTRUDER with SWITCHING_NOZZLE
...
Fix #11183
2018-07-02 17:25:15 -05:00
5700360adf
[1.1.x] Slovak translation update ( #11174 )
2018-07-01 23:15:14 -05:00
defaa93121
Do a hard kill for failed homing moves ( #11160 )
2018-06-30 21:53:58 -05:00
c4fbbcaf46
Lose the old HOMEAXIS macro
2018-06-30 18:07:40 -05:00
ca6ddbc555
Detect endstop hits in any direction
2018-06-30 17:26:49 -05:00
1caa01a9a2
Fix Trigorilla 1.4 pin defines
...
See #11097
2018-06-30 13:45:41 -05:00
a294ec3836
Add delta feedrate scaling ( #11152 )
2018-06-30 13:44:37 -05:00
a789ab4005
[1.1.x] Git ignore for VS ( #11156 )
...
Add missing VS file
2018-06-30 02:51:20 -05:00
718a22e836
Non-conflicting CS pins for MKS Gen L
2018-06-30 02:35:45 -05:00
be3e006fc8
Fix G33 compile warning
2018-06-29 23:20:59 -05:00
654f0bed25
Remove JUNCTION_DEVIATION_INCLUDE_E option ( #11146 )
2018-06-29 22:41:56 -05:00
609e7da3f3
Fix and tweak POWER_LOSS_RECOVERY ( #11150 )
2018-06-29 22:40:49 -05:00
67475374ae
Fix SKEW_CORRECTION compile error
2018-06-29 19:37:47 -05:00
485d50ecb0
Ignore Z min endstop with separate Z probe
...
To allow for the case where a Z endstop (e.g., hall effect) is higher than the probe trigger point, don't check the Z min endstop during probe moves. See #11134
2018-06-28 05:09:45 -05:00
5788a393c0
Fix up microsteps conditionals
2018-06-28 00:07:03 -05:00
5e03dede18
Eliminate stepper.* signed/unsigned warnings
2018-06-27 23:06:49 -05:00
b880028334
Fix stepper/planner block handling, race conditions ( #11136 )
...
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-06-27 18:11:23 -05:00
cff2201629
Poll all endstops, even when stationary ( #11125 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-06-27 04:19:05 -04:00
e352c1e52d
Endstop patch followup
2018-06-27 00:12:42 -05:00
04fc715c91
Add minimum step dir delay option, A4988 pulse note ( #11122 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-06-26 22:28:46 -04:00
4d5c655f8d
Make max_e_jerk an array to save CPU ( #11121 )
...
Co-Authored-By: gloomyandy <andy-git@gloomy-place.com>
2018-06-26 22:09:38 -04:00
0a2d3ecfd4
[1.1.x] Fix advanced pause init values ( #11096 )
...
Fixed for cycle used to initialize default values
2018-06-26 14:38:08 -04:00
8600cbb01b
Clear Max7219 without test pattern
2018-06-25 11:54:14 -04:00
dd9c65d0be
[1.1.x] Fix stepper/planner race condition, Stepper pulse timer ( #11084 )
...
* Fix planner/stepper race condition
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
Co-Authored-By: AnHardt <github@kitelab.de>
* Fix stepper pulse timing
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-06-22 10:53:46 -04:00
53745446f9
Fix LIN_ADVANCE max_e_jerk_factor
...
According to https://github.com/MarlinFirmware/Marlin/issues/9917#issuecomment-399204568
2018-06-21 21:38:52 -04:00
52f5efb78d
Filter endstops state at all times ( #11076 )
2018-06-21 20:13:16 -05:00
94787114f1
Merge pull request #11074 from thinkyhead/bf1_value_editing
2018-06-21 20:12:48 -05:00
7632df6820
add the move_z_after_probing() functionality to UBL's G29 J
2018-06-21 13:22:40 -05:00
bd10791b6d
Edit Z fade as whole numbers
2018-06-21 11:53:29 -04:00
b05fcad7fe
Fix value editing with callback
2018-06-21 11:48:27 -04:00
3bb332b440
Use Tool 0 for Dual X Axis G29
...
See https://github.com/MarlinFirmware/Marlin/issues/5597#issuecomment-397683325
2018-06-19 22:54:30 -05:00
e0b4abd3eb
Don't reset stepper timeout for all g-codes
2018-06-19 21:50:09 -05:00
3ca4f09680
Tiny improvement to M7219
...
The registers within the Max7219 can get corrupted a number of ways. This allows the Max7219 to be reset and fully initialized.
And... it also allows the user to see the initialization pattern.
2018-06-19 18:21:19 -05:00
7cdaf69ab7
[1.1.x] Fix Italian msg len ( #11057 )
...
Fix message to long for 12864 display
2018-06-18 22:04:35 -05:00
Scott Lahteine