Commit Graph

59 Commits

Author SHA1 Message Date
Jonathan Bastien-Filiatrault
0f73afb0b0 Avoid defining overriding definitions for the RepRapDiscount Smart
Controller. Remove common definitions. Harmonize declaration order.
2012-11-07 16:04:28 -05:00
Jonathan Bastien-Filiatrault
36b452c7ac Remove abbrs. 2012-11-07 15:42:18 -05:00
Jonathan Bastien-Filiatrault
3cbaad9288 RepRapDiscount Smart Controller pin definitions. 2012-11-06 20:32:13 -05:00
Bracken Dawson
f5631a89e8 Add dummy Emergancy Pin to Gen7 1.4
Change required after pulling from ErikZalm.
2012-10-26 22:28:37 +01:00
Bracken Dawson
a4f9e1ebf2 Merge git://github.com/ErikZalm/Marlin into Marlin_v1 2012-10-26 22:20:35 +01:00
Bracken Dawson
2873d67b17 Put bogus temp override back in Gen7 up to 1.3
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
2012-10-26 22:17:26 +01:00
brupje
d07b6e93d5 Add support for Megatronics 2012-10-14 14:05:12 +03:00
Erik vd Zalm
abf0693e8e Added KILL_PIN -1 to gen7 boards 2012-09-04 08:20:27 +02:00
Drakelive
d728e35658 Update Marlin/pins.h 2012-08-30 23:36:49 +03:00
Bracken Dawson
47d4f55bc0 Fix Gen7 1.4 pinout
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
2012-08-22 23:15:46 +01:00
Enchiridion
50cde90324 Added support for dual Z axis stepper drivers 2012-08-04 00:32:26 -06:00
Chris Palmer
538189cc19 Fixed soft limits when the origin is in the middle.
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.

Saguinololu limit pins change from MIN to MAX according to the homing direction.
2012-07-14 22:24:26 +02:00
Daid
e9bec9b6fe Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6) 2012-05-24 18:36:55 +02:00
Guan Yang
602c8ee02b Melzi support 2012-05-09 18:37:07 -04:00
Bernhard
464b755918 added support for the UltiController 2012-04-22 20:55:56 +02:00
Michel Pollet
5550e893d5 New board variant, Open Motion Controller
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/

Signed-off-by: Michel Pollet <buserror@gmail.com>
2012-03-22 13:51:21 +00:00
Erik van der Zalm
2e749d60c3 Added DISABLE_MAX_ENDSTOPS 2012-03-12 20:32:14 +01:00
ErikZalm
19a47dae4a Merge pull request #99 from Justblair/master
Better pin configuration for rotary encoder in RAMPS boards
2012-03-11 04:34:59 -07:00
Erik van der Zalm
c077316b2b Added PID autotune. (experimental)
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
2012-03-08 21:43:21 +01:00
Blair Thompson
02ee9e3d30 Changed Pin Assignment for the RAMPS motherboard so that LCD and Rotary encoder are all wired to AUX-4
This simplifies wiring for those with RAMPS 1.3 and 1.4 boards.
2012-03-04 21:34:20 +00:00
Erik van der Zalm
cb0c84e075 Merge remote-tracking branch 'justblair/master' into Marlin_v1 2012-03-03 20:20:55 +01:00
ErikZalm
1d5809d458 Merge pull request #88 from daid/Marlin_v1
Made plan_buffer_line arguments const...
2012-03-03 11:18:14 -08:00
Erik van der Zalm
ed951b1977 Fixed RAMPS 1.2 support (Found and fixed by rrhb) 2012-03-03 20:15:41 +01:00
Blair Thompson
f278e1c00f This is in my opinion a much better way of dealing with SD cards than my previous fix.
Instead of adding a momentary switch to fake the insertion of the card I have modified the ultralcd menu item:

Card Menu -> Refresh

to reinitialise the card providing that the SDCARDDETECT pin has been set to -1 in the pins.h file.  This requires one less switch on the front panel and the refresh menu item is in the most relevent place for a user who wishes to inert a card and then print from it.

It also means that the "Card inserted" messages do not bother the users of these card readers (they dont make sense for users without SCCARDDETECT)
2012-03-03 16:30:31 +00:00
Daid
00d33e6b82 Typo fix 2012-02-29 19:01:21 +01:00
Daid
7d124478fa Only protect the heater pins for the defined extruders.
Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
2012-02-29 15:49:02 +01:00
ErikZalm
1ebe7d1ab6 Merge pull request #83 from phord/tempfix
Add explicit #define for bogus temp override
2012-02-27 08:36:45 -08:00
Phil Hord
b65ef8d66c Add support for upcoming Gen7 v1.4
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board.  Add a new motherboard type to
support this feature.
2012-02-26 20:39:49 -05:00
Phil Hord
740f0c7690 Add explicit #define for bogus temp override
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature.  But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
2012-02-26 20:26:16 -05:00
Phil Hord
ba8500a236 pins.h: Define Z_MAX_PIN for Gen7 board
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail.  Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
2012-02-26 20:18:39 -05:00
Changwoo Ryu
7b14953c99 Fix build on Sanguino based boards with ATmega1284P 2012-02-27 04:12:55 +09:00
Daid
286d5003fa Fixed compiler warning for Sanguino compile 2012-02-26 17:35:01 +01:00
Erik van der Zalm
ce714fe306 Fixes in pins.h 2012-02-25 22:55:17 +01:00
Erik van der Zalm
35e57bf149 Added gen6 deluxe. 2012-02-25 17:44:45 +01:00
Erik van der Zalm
84ea2d61e8 Moved gen7 boards to motherboard type 10, 11 and 12.
Split ramps1.3 in Sprinter like config and multiextruder config.
2012-02-24 23:34:41 +01:00
Erik van der Zalm
d298dd121f merged SBUBA82 and Justblair 2012-02-21 20:26:59 +01:00
Blair Thompson
a05a261b72 Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
2012-02-18 23:56:31 +00:00
Blair Thompson
1b6765ed12 Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface 2012-02-18 18:25:04 +00:00
Christian Thalhammer
e661578c84 support for GEN7 1.1,1.2 and 1.3 2012-02-17 10:46:48 +01:00
Christian Thalhammer
d309565b56 Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
Conflicts:
	Marlin/Configuration.h
2012-02-13 13:07:55 +01:00
Erik van der Zalm
11518a987f merged with triffid fork 2012-02-12 13:58:36 +01:00
Erik van der Zalm
da040fd393 Fixed ultimaker heater 1 pins. (Thanks daid) 2012-02-09 17:19:45 +01:00
Christian Thalhammer
a11f3b2d2f - Pins for modified GEN7 assigned
- Added support for ATMega1284
2012-02-06 11:49:23 +01:00
Erik van der Zalm
9f139d6e0e Added MAX6675 support. (Thanks to gregfrost)
Needs some work to remove the blocking in read max6675.
2012-02-05 13:05:07 +01:00
Erik van der Zalm
e45e5c68bb Added support for Gen3+ (Pins file only)
Added late z enable. (blddk request)
Only calculate look ahead if >2 moves in buffer.
Removed some FORCE_INLINE to save memory.

Signed-off-by: Erik van der Zalm <erik@vdzalm.eu>
2012-02-05 12:42:15 +01:00
Michael Moon
ab01658fd2 local configuration stuff- WATCHPERIOD causes breakage, disable. few other misc changes 2012-01-24 17:02:45 +11:00
Michael Moon
71dc82e0b4 my local configuration 2012-01-24 13:19:37 +11:00
Bernhard
cee5f9020a added suicide pin for a power supply to the arduino that is only active if the arduino is holding high for an output. 2012-01-15 17:06:10 +01:00
Bernhard
415aadf704 lcd panel bed support
advance and ultipanel not any more in default config
2011-12-22 11:45:52 +01:00
Erik van der Zalm
e017228569 Merged multiple extruder support.
Soft PWM. (Sanguinololu can also have PID temperature control)
Interrupt save WRITE for addresses > 0x0FF
2011-12-12 19:34:37 +01:00