Commit Graph

2995 Commits

Author SHA1 Message Date
AnHardt
d17f7ebc8a Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
instead of 1000.  Else we get errors with times over 32 seconds.
2015-07-27 20:30:53 -05:00
Scott Lahteine
bea6739774 Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527) 2015-07-27 20:24:33 -05:00
Scott Lahteine
81bba7ed88 More sanity checking for extruder requirements (PR#2531) 2015-07-27 10:14:43 -05:00
AnHardt
87a97f3724 Fix conditions for display strings 2015-07-26 20:41:21 -05:00
AnHardt
aaccea0260 Shift some display only strings from language.h to lenguage_en.h
and translate them to German.
2015-07-26 20:41:15 -05:00
Scott Lahteine
e4c01f1c7e Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507) 2015-07-26 20:40:27 -05:00
Scott Lahteine
ab6f1fdf8b Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
2015-07-26 20:36:37 -05:00
Richard Marko
1183c10a2e makefile: drop -q -q (much quiet) from avrdude flags
Annoying when trying to figure out if uploading
actually does something.
2015-07-26 20:31:31 -05:00
Richard Marko
0e064357f4 makefile: use /etc/avrdude/avrdude.conf on linux
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
2015-07-26 20:31:31 -05:00
Scott Lahteine
bcb7d5a149 Improve sanitycheck for TEMP_SENSOR_1 2015-07-25 21:17:36 -05:00
Scott Lahteine
5b24f59401 Add sanity checks for temp sensors 2015-07-25 21:17:36 -05:00
AnHardt
fd0e81b0c7 Distinguish between BUZZER and SPEAKER (PR#2513)
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.

There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker

* replace the PWM based tone()-function again with a on-delay-off-delay loop.

Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
Scott Lahteine
e2957df05c Shorthand for do_blocking_move_to 2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50 Adjust comment on Z adjustment 2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc Patch for G29 final Z position
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
2015-07-24 22:07:41 -05:00
AnHardt
088e09e052 Add forgotten Marlin_main.cpp 2015-07-24 22:04:49 -05:00
AnHardt
8b876241bd Some more servo code tweaks
Just set up the pin. Don't move to a random position.

Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.

SERVO_LEVELING is the wrong condition to deactivate the servos.

Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
2015-07-24 22:00:25 -05:00
Scott Lahteine
f7e7862588 Better Sanguinololu & Graphical Controller (PR#2504)
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
2015-07-23 23:47:07 -05:00
Scott Lahteine
a1154d4a20 Enable Y and sanity-check CoreXZ (PR#2509) 2015-07-23 23:46:27 -05:00
Scott Lahteine
932f1c109e Move servos to the top in pins_MEGACONTROLLER.h 2015-07-23 22:51:41 -05:00
Scott Lahteine
90f8ddfc1e Apply MINIPANEL to other configs 2015-07-23 22:51:41 -05:00
AndySze
00dbf69b6d add MINIPANEL defines 2015-07-23 22:51:40 -05:00
AndySze
8ac5e56934 fixed some format problems and cleaned code 2015-07-23 22:51:40 -05:00
AndySze
eef595aa64 add makerlab mega controller pin configs 2015-07-23 22:51:40 -05:00
AnHardt
4e14e152fa Add Travis tests for CORXY and COREXZ 2015-07-23 19:52:48 -05:00
AnHardt
27d7d2ccab Correct bracketing for COREXY-XZ 2015-07-23 19:52:21 -05:00
Scott Lahteine
469843427d Reduce code in gcode_M81 (PR#2497) 2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9 Mark unchanging arrays as const (PR#2494)
The compiler may be able to optimize if it knows an array won’t be
changing.
2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301 Add COUNT macro and apply 2015-07-22 18:16:05 -05:00
Scott Lahteine
d85861d296 Move macros, add ENABLED/DISABLED, add includes 2015-07-22 18:16:05 -05:00
Scott Lahteine
17960fd2b0 Neaten up pins_MEGATRONICS.h (PR#2493) 2015-07-22 17:23:22 -05:00
Scott Lahteine
aac2b9aa9d Reduce code in gcode_M84 (PR#2492)
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
2015-07-22 17:22:01 -05:00
Scott Lahteine
4971fa73f9 Add a sanitycheck error for old servo settings (PR#2491)
- Documentation solution for #2476
2015-07-22 16:35:10 -05:00
Scott Lahteine
96ace72ddc Servos attach/detach based only on servo config
Assuming #2470 fixed up the main issue.
2015-07-22 16:34:26 -05:00
Richard Wackerbarth
b80a6a8d31 Correct Kossel Pro Configuration_adv (PR#2473) 2015-07-22 16:32:08 -05:00
Scott Lahteine
000a6fce46 Extract update_endstops from stepper ISR (PR#2474) 2015-07-19 18:33:18 -05:00
Scott Lahteine
e83eac312e Move plan_arc next to prepare_move 2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d G2/G3 Arcs for Delta
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
2015-07-19 16:18:46 -05:00
Scott Lahteine
9f53e2f0c9 Implement COREXZ in stepper.cpp and planner.cpp 2015-07-19 16:17:03 -05:00
Scott Lahteine
fa00e1d97f Explode conditions common to corexy and cartesian 2015-07-19 16:17:03 -05:00
Scott Lahteine
c7dd5527b4 Add a C_AXIS and Z_HEAD to support COREXZ 2015-07-19 16:17:03 -05:00
Scott Lahteine
129f986ccf Add COREXZ option to configurations 2015-07-19 16:17:03 -05:00
Scott Lahteine
69b0490b77 Show minimal preheat options in menus (PR#2471) 2015-07-19 16:14:59 -05:00
Scott Lahteine
eacfe132aa Change the name of servos[] and servo_t 2015-07-19 11:35:48 -07:00
Scott Lahteine
3b23ccd366 Patch servos code for move
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
2015-07-19 11:24:23 -07:00
Richard Wackerbarth
54ddc1d417 Simplify DRY RUN (PR#2358)
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.

Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
2015-07-19 10:15:53 -05:00
Scott Lahteine
944090c19c Optimize lsDive logic 2015-07-19 10:13:40 -05:00
Scott Lahteine
417706e578 Include space for the terminating nul in lsDive 2015-07-19 10:13:39 -05:00
Scott Lahteine
f3c1a6b19c Reduce lsDive stack usage to the minimum 2015-07-19 10:13:39 -05:00
Patrick Bogen
fba4e6241b Specify print format for reporting invalid tmp_extruder (PR#2465) 2015-07-18 16:40:01 -05:00
AnHardt
d15d869267 Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
to make clear - it's not a question but an order.
2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5 Move the Z probe as far as needed to trigger the switch (PR#2461) 2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389 Fixup comments in code_seen 2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650 Call code_seen only once per parameter 2015-07-16 16:40:52 -05:00
Scott Lahteine
b742af2e2a Move Y_STOP_PIN for Printrboard with SD (PR#2420) 2015-07-16 16:39:55 -05:00
Scott Lahteine
baa9199973 Define extern delta only for delta 2015-07-16 16:36:30 -05:00
Scott Lahteine
77e80ef367 Require extruders for thermal code 2015-07-16 16:36:30 -05:00
Scott Lahteine
3bde4f4855 Require temp sensor for bed thermal protection 2015-07-16 16:36:30 -05:00
Scott Lahteine
82a3ed2f9a Cleanup and dev notes in Marlin.h 2015-07-16 16:36:30 -05:00
Scott Lahteine
db23b9b184 Minor tweak to M204 code (PR#2457) 2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
Scott Lahteine
552a327df8 Fix lsDive filename stack overrun (PR#2449) 2015-07-16 10:23:56 -05:00
AnHardt
a6628f12cc Eliminate the further use of the pin-parameter 2015-07-15 20:50:58 -05:00
AnHardt
8504992e9f Remove the additional pin variable in Servo.cpp
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
2015-07-15 20:50:58 -05:00
AnHardt
ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
Scott Lahteine
de25a48dec Remove PID examples from preconfigured configs 2015-07-15 19:13:53 -05:00
Scott Lahteine
7456710a1f Update configs formatting 2015-07-15 19:13:47 -05:00
Scott Lahteine
391386dd94 Update configs for new servo deactivation 2015-07-15 19:13:40 -05:00
AnHardt
5243d8b523 Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default 2015-07-15 17:39:43 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
AnHardt
40b6edcad7 Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
2015-07-15 17:39:43 -05:00
AnHardt
2ddb2a2be9 Add Servo::move() to servo.cpp
move(pin, angel) - Sequence of attach(pin), write(angel),
                   if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.

As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()

Here a function to handle the complete sequence.
2015-07-15 17:39:43 -05:00
mkile
8a01e5fb7a Update Russian translation (PR#2443)
Slightly updated translation.
2015-07-15 10:35:36 -05:00
Richard Wackerbarth
e83575537a Compiler defines USBCON for USB devices (PR#2433) 2015-07-15 10:32:11 -05:00
ayberkozgur
7268d46508 Always calculate extruder temperature PID d term (PR#2432) 2015-07-13 13:22:26 -05:00
Scott Lahteine
87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine
a0351bdb73 Remove STEPPER_RESET_FIX option 2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine
8e61314323 Use RIGIDBOT_PANEL for consistency with online docs 2015-07-09 11:36:46 -05:00
Scott Lahteine
4b204da3c1 Cleanup of pins_RAMPS_13.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
536f86e896 RigidBot CONTROLLERFAN_PIN in Configuration_adv.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
f068e46661 RigidBoard include for pins.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
9ebcae496d RIGIDBOARD / RIGIDPANEL 2015-07-09 11:36:46 -05:00
Scott Lahteine
c3c605c658 Move note about LiquidTWI2 to Configuration.h (PR#2406) 2015-07-09 05:33:17 -05:00
Scott Lahteine
4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
bc0fdbe88e Use SERIAL_EOL in SERIAL_PROTOCOLLN macros 2015-07-07 06:59:10 -05:00
Scott Lahteine
d78ebbc0e9 Remove unused MSG_OK_B and MSG_OK_T 2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt
0e1cf78f5c Remove code for testing if probing range is too small (PR#2390)
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
2015-07-07 06:58:01 -05:00
AnHardt
d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391)
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab Replace "target" with "destination" in M600 (PR#2374)
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
Scott Lahteine
a5033c3652 Enable LCD_PIN_RESET if it exists (PR#2375) 2015-07-04 05:53:22 -05:00
AnHardt
23c8c5348f Z-height fix V2b (PR#2351)
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a z-probe offset fix (PR#2361)
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
42465ee444 Cleanup of comments & spacing 2015-06-28 08:20:28 -05:00
Scott Lahteine
9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
Scott Lahteine
bb44fe17cf Fix typo in buzzer.h endif (PR#2337) 2015-06-27 06:10:19 -05:00
AnHardt
36746143a1 Correct output of M48 (PR#2336)
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine
d135b15bb8 Init all endstop bits to 0 (PR#2332) 2015-06-26 07:10:22 -05:00
Scott Lahteine
5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
Jaime van Kessel
b8b5762e55 Update Ultimaker URL 2015-06-25 09:12:44 -05:00
Jaime van Kessel
d5bfbf5a59 Added correct dutch translation for calibrate. 2015-06-25 09:12:44 -05:00
Scott Lahteine
149c474e55 Updated Russian language (PR#2325)
Gleaned from
https://github.com/MarlinFirmware/Marlin/commit/4ac14a7e5fa8e6e395436664
8976eafd1ae220ae
2015-06-22 23:07:19 -04:00
AnHardt
722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
AnHardt
c461975140 Rename and repair MELZI_1284 (PR#2301)
to MELZI_MAKR3D.

Fix for #2288
As the normal MELZI also can have a 1284.
2015-06-22 22:30:07 -04:00
schlotzz
1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
Scott Lahteine
ec93383ec8 Add SanityCheck for bed probe position settings (PR#2282) 2015-06-15 20:22:44 -05:00
Scott Lahteine
dc40a5f6e0 Patch up more outdated config lines 2015-06-15 20:20:32 -05:00
Scott Lahteine
98c9111a7d Update delta configs with latest settings 2015-06-15 20:20:32 -05:00
Scott Lahteine
e6baf8afd9 Fix up allen key settings in delta configs 2015-06-15 20:20:31 -05:00
Scott Lahteine
3b293fc5d1 Move Delta settings lower in delta files 2015-06-15 20:20:31 -05:00
Scott Lahteine
df21857583 Move extruder offset settings next to extruders setting 2015-06-15 20:20:31 -05:00
Scott Lahteine
2dd1859247 Cleanup spaces and comments in configs and conditionals 2015-06-15 20:20:31 -05:00
Scott Lahteine
a274769f4f Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54 Fix up spacing for filament sensor values 2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe Fix configurator section directives and values lists 2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6 Move Z Safe Homing point to the middle of the movement range 2015-06-15 20:20:31 -05:00
Scott Lahteine
318318b02f Add pins_RAMPS_13_EFB.h to reduce redundancy 2015-06-15 20:17:09 -05:00
Scott Lahteine
346c8b339b Remove a test from pins_RAMPS_13.h
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
2015-06-15 20:15:38 -05:00
AnHardt
b93cddfcc9 Add lost MKS_BASE to pins.h (PR#2297) 2015-06-15 10:23:46 -05:00
AnHardt
6ab7b560af Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine
1d94d098bf Formatting tweaks as part of fixing issue 1497 2015-06-14 19:57:27 -05:00
Scott Lahteine
e602c28ad9 Set auto fan pins to OUTPUT during init
Fixes the problem of these pins being left in INPUT state, as described
in #1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
90f858aa85 Use translated strings for axis movement (PR#2280)
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
2015-06-14 08:16:00 -05:00
Scott Lahteine
e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
Scott Lahteine
6b1b3adaf0 Consistent punctuation in SanityCheck errors (PR#2283) 2015-06-12 09:31:02 -05:00
MagoKimbra
eb81982fcd Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
filipmu
b0860adab6 Fix volumetric multiplier display for filament sensor (PR#2264)
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
2015-06-12 02:19:27 -05:00
AnHardt
45642b7fe8 Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
wurstnase
c85a486445 make the dual z-endstop optional (PR#2277)
it's disabled by default
2015-06-10 15:45:59 -05:00
Scott Lahteine
962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Richard Wackerbarth
06ae832276 Deprecate Support for Arduino IDE < 1.0.5
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
2015-06-08 17:15:28 -05:00
Scott Lahteine
ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263)
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
aad121864e Include "Z" in M851 report 2015-06-08 05:09:27 -05:00
Scott Lahteine
96a3fba8ac Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
fmalpartida
f92907183c Updated SAV MkI pin header. 2015-06-08 05:07:11 -05:00