MPCNC/Firmware
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
6,190 Commits 1 Branch 0 Tags 96 MiB
92b4459f6c
Commit Graph

1467 Commits

Author SHA1 Message Date
Scott Lahteine
f9a192c7e3 Move setup() and loop() to the end 2016-09-13 03:32:59 -05:00
Scott Lahteine
74d7f5e57b Patch SCARA example config 2016-09-13 03:32:59 -05:00
Scott Lahteine
6ab54c60b1 Add conditionals for kinematics, leveling 2016-09-13 03:32:59 -05:00
Scott Lahteine
9248cfb0ad Bed leveling that accounts for home XYZ 2016-09-10 13:47:21 -05:00
Scott Lahteine
6ac9d895ca Tweak Filament Width variables 2016-09-10 13:29:25 -05:00
Scott Lahteine
68ba45572e Don't say "heating complete" unless done 2016-09-10 13:29:25 -05:00
Scott Lahteine
2bfc6fe1b0 Move XYZ constants closer to the top 2016-09-10 13:25:44 -05:00
Scott Lahteine
ad659b5f91 Merge pull request #4725 from thinkyhead/rc_log_machine_info 
Log machine info in G28 and G29
 2016-09-01 23:58:59 -05:00
Scott Lahteine
7e20448a2d Add HOMING_Z_WITH_PROBE conditional 2016-08-30 13:29:26 -05:00
Scott Lahteine
0e4107da34 Minor cleanup of homeaxis, etc. 2016-08-30 13:29:26 -05:00
Scott Lahteine
fd2269f489 Log machine info in G28 and G29 2016-08-28 20:48:28 -05:00
Scott Lahteine
6eaf4f4909 Fix spacing of debug output in homeaxis 2016-08-28 19:43:33 -05:00
Scott Lahteine
0729a8f08d Use the probe travel height for pre-probe move 
Instead of using the home_bump for Z to move close to the bed before doing a slow probe, use the probe travel height.
 2016-08-28 19:13:08 -05:00
Scott Lahteine
dd94d0b9d5 Fix bed probing bug without PROBE_DOUBLE_TOUCH 
If `PROBE_DOUBLE_TOUCH` wasn't enabled, the probe move could be way too short! See #4701 for example.
 2016-08-28 19:00:25 -05:00
Scott Lahteine
35a0c46f16 Tweak debug output for probe in G29 2016-08-28 18:44:44 -05:00
Scott Lahteine
2cb63f0bf7 Merge pull request #4719 from thinkyhead/rc_delta_homing_patch 
Marlin patches for homing, esp. Delta
 2016-08-27 20:46:50 -05:00
Scott Lahteine
73d86098b7 Marlin patches for homing, esp. Delta 2016-08-27 20:32:05 -05:00
Scott Lahteine
338bc768b1 Merge pull request #4717 from thinkyhead/rc_log_the_probe 
Debug logging of nozzle type and offsets
 2016-08-27 20:24:19 -05:00
Scott Lahteine
d641344d3a Remove redundant probe offset in homing 2016-08-27 19:58:56 -05:00
Scott Lahteine
00638131e5 Debug logging of nozzle type and offsets 2016-08-27 15:21:01 -05:00
Scott Lahteine
991a34aff2 Log whether homing with probe or endstop 2016-08-26 15:50:10 -05:00
esenapaj
1749a7fae3 Suppress warning 2016-08-24 00:18:06 +09:00
Scott Lahteine
d07d85ac9f Ensure probe points at the delta edge are kept 2016-08-23 05:09:56 -05:00
Scott Lahteine
27b80b1dd1 Merge pull request #4667 from thinkyhead/rc_M211_sw_endstop_switch 
M211: Enable/Disable Software Endstops
 2016-08-21 06:44:00 -05:00
Scott Lahteine
2f223b8c79 Use ABC and XYZ for "3" 2016-08-21 00:10:08 -05:00
Scott Lahteine
4cd1ad8f28 Adjustments to M209, G28, M605 2016-08-21 00:10:08 -05:00
Scott Lahteine
280534c06f Add M211: Enable/Disable Software Endstops 2016-08-21 00:10:08 -05:00
Scott Lahteine
01d4703429 PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION 
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
 2016-08-20 23:35:27 -05:00
MagoKimbra
28d1e5a946 Fix_Zig_Zag 2016-08-20 11:28:08 +02:00
Scott Lahteine
4d4c00d69c Merge pull request #4651 from thinkyhead/rc_homing_vs_leveling_z 
Improvements to homing / leveling
 2016-08-19 15:45:49 -05:00
Scott Lahteine
12d72363cb Do Delta radius check without sqrt 2016-08-19 05:05:48 -05:00
Scott Lahteine
044f800be9 Use SERIAL_PROTOCOLLNPGM in G28 2016-08-19 04:45:33 -05:00
Scott Lahteine
d309a9647d Include probe offset for moving "close to the bed" 2016-08-19 04:45:33 -05:00
Scott Lahteine
35a08eeaeb Use Z_HOME_DIR over axis_home_dir where we can 2016-08-19 04:45:32 -05:00
Scott Lahteine
55355a4fb8 Make probed points more symmetrical 2016-08-19 04:32:03 -05:00
Scott Lahteine
1f776f6034 Tweak some code comments 2016-08-19 04:32:02 -05:00
Scott Lahteine
748228cf40 Use named indices for delta_grid_spacing 2016-08-19 04:32:02 -05:00
Scott Lahteine
ead333e7da line_to_axis_pos => do_homing_move 2016-08-19 04:32:02 -05:00
Scott Lahteine
7a4ccd7967 Add do_probe_move with Z fixes 2016-08-19 04:32:02 -05:00
Scott Lahteine
a1bad589c9 Augment debug/homing logging 2016-08-19 04:32:02 -05:00
Scott Lahteine
41b5c48129 Update software endstops if EEPROM is loaded 2016-08-19 04:32:01 -05:00
Scott Lahteine
628dcbc764 extruder_multiplier => flow_percentage 2016-08-18 22:13:47 -05:00
Scott Lahteine
d63b8e2b2b Additional details for I2C_SLAVE_ADDRESS 2016-08-15 19:27:53 -07:00
Scott Lahteine
bd928a69ec Add request, capture, flush to TWIBus 2016-08-15 00:04:20 -07:00
Scott Lahteine
97e0aed304 Further refinements of TWIBus 2016-08-13 18:32:41 -07:00
Scott Lahteine
67f119d18b Add an i2c request handler 2016-08-11 18:09:18 -07:00
Scott Lahteine
d6a7ca6553 Merge pull request #4584 from thinkyhead/rc_delta_cal_more 
Use configured feedrates, center in DELTA_CALIBRATION_MENU
 2016-08-11 14:04:05 -07:00
Scott Lahteine
52560e257f Merge pull request #4595 from thinkyhead/rc_i2c_slave 
Add support for i2c slave address
 2016-08-11 12:39:26 -07:00
Scott Lahteine
cd496dd9bd do_blocking_move_to can't be 'inline', takes const ref args 2016-08-11 12:05:55 -07:00
Scott Lahteine
dd75fca4d9 Make M155 / M156 a bit more flexible 2016-08-11 00:52:01 -07:00
Scott Lahteine
a99ecf71d8 Add support for i2c slave address 2016-08-10 23:30:35 -07:00
Scott Lahteine
b63d70b186 Fix serial output for MBL, M303 2016-08-10 18:49:52 -07:00
Scott Lahteine
45f67164b6 Simplify the delay in kill() 2016-08-08 21:49:34 -07:00
Scott Lahteine
367dad5902 Sanity check Z_DUAL_ENDSTOPS with DELTA 2016-08-07 17:08:41 -07:00
Scott Lahteine
7b2abe6fc8 Use steps_to_mm in extruder runout prevent 2016-08-07 00:28:52 -07:00
Scott Lahteine
d320065320 Within Marlin, maintain most feed rates in mm/s 2016-08-07 00:28:52 -07:00
Scott Lahteine
a00783c41f Format probe stowed test code 2016-08-06 14:31:07 -07:00
AnHardt
f37e8a31d7 Make Allen Key Probe stow 
by switching off the tests for the probe before the stow move.
 2016-08-06 14:30:38 -07:00
Scott Lahteine
938e6d15c4 Patch up some flaws, here and there 2016-08-05 08:17:37 -07:00
Scott Lahteine
7e2bd9a233 Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT 2016-08-03 21:18:38 -07:00
Scott Lahteine
445458c221 Don't include zprobe_zoffset in do_probe_raise 2016-08-03 21:12:02 -07:00
Scott Lahteine
b73203a0b7 Move some includes around to uncover missing deps 2016-08-02 19:37:46 -07:00
Scott Lahteine
0f030aface Merge pull request #4503 from AnHardt/fix-retract 
Correct typo in retract()
 2016-08-02 15:04:55 -07:00
Scott Lahteine
330f82971b Buzzer requires BEEPER_PIN 2016-08-02 14:05:37 -07:00
AnHardt
39c4603598 Correct typo in retract. 2016-08-02 21:06:08 +02:00
Scott Lahteine
6eed37aafb Merge pull request #4486 from thinkyhead/rc_pid_add_extrusion_rate_off 
PID_EXTRUSION_SCALING, disabled by default
 2016-07-31 18:23:51 -07:00
Scott Lahteine
4bf3526d00 Merge pull request #4463 from thinkyhead/rc_azteeg_x3_eeb 
Wrangle RAMPS variants and derivatives
 2016-07-31 18:22:49 -07:00
Scott Lahteine
63fd1f49a6 PID_EXTRUSION_SCALING, disabled by default 2016-07-31 17:49:34 -07:00
Scott Lahteine
f388beafa1 Merge pull request #4476 from otvald/RCBugFix 
FIX for endstop adjustemt on delta is offset
 2016-07-31 01:09:54 -07:00
Thomas Otvald Jensen
fe059f1221 During homing, line_to_axis_pos will make a path which moves across the 
endstop trigger point. The move is stopped at endstop, so current_position
should also be adjusted to reflect this!

Caused error in subsequent call in endstop adjustment, since the movement
would assume a wrong starting position.
 2016-07-30 16:50:31 +02:00
esenapaj
bd73e6d3c8 Fix for PR #4452 (Additional heater-state output changes) 
・Add missing ';'
 2016-07-30 22:49:30 +09:00
Scott Lahteine
bdac2eb13a Don't set non-existent SLED_PIN 2016-07-30 04:17:21 -07:00
Scott Lahteine
8e2f095dde Merge pull request #4456 from jbrazio/speaker-type3 
Improvement to non-blocking speaker
 2016-07-30 04:07:08 -07:00
Scott Lahteine
9e21b2e51d Merge pull request #4455 from AnHardt/double-bump-feature 
double bump probing as a feature
 2016-07-29 20:00:10 -07:00
Scott Lahteine
db4d03bc81 Merge pull request #4452 from thinkyhead/rc_fix_heaterstates_part_2 
Additional heater-state output changes
 2016-07-29 19:58:00 -07:00
Scott Lahteine
844a4e799e Account for DELTA in Planner::refresh_positioning 2016-07-29 18:41:11 -07:00
AnHardt
7188ce0ad6 double bump probing as a feature 
Why double touch probing is not a good thing.

It's widely believed we can get better __probing__ results when using a double touch when probing.

Let's compare to double touch __homing__.
Or better let's begin with single touch __homing__.
We home to find out out position, so our position is unknown.
To find the endstop we have to move into the direction of the endstop.
The maximum way we have to move is a bit longer than the axis length.
When we arrive at the endstop - when it triggers, the stepper pulses are stopped immediately.
It's a sudden stop. No smooth deacceleration is possible.
Depending on the speed and the moving mass we lose steps here.
Only if we approached slow enough (below jerk speed?) we will not lose steps.

Moving a complete axis length, that slow, takes for ever.
To speed up homing, we now make the first approach faster, get a guess about our position,
back up a bit and make a second slower approach to get a exact result without losing steps.

What we do in double touch probing is the same. But the difference here is:
a. we already know where we are
b. if the first approach is to fast we will lose steps here to.
But this time there is no second approach to set the position to 0. We are measuring only.
The lost steps are permanent until we home the next time.

So if you experienced permanently rising values in M48 you now know why. (Too fast, suddenly stopped, first approach)

What can we do to improve probing?
We can use the information about our current position.
We can make a really fast, but deaccelerated, move to a place we know it is a bit before the trigger point.
And then move the rest of the way really slow.
 2016-07-30 03:00:49 +02:00
Scott Lahteine
c31f56a38c Deprecate EXTRUDER_WATTS and BED_WATTS 2016-07-29 17:34:14 -07:00
Scott Lahteine
e1970b4b28 Show power output in same order as temp output 2016-07-29 14:55:22 -07:00
Scott Lahteine
74df828acc Show ADC values inline rather than after 2016-07-29 14:55:18 -07:00
João Brázio
2b5faa61e2 Consolidates Buzzer and Speaker into a single object 2016-07-29 19:25:39 +01:00
Scott Lahteine
b40661cb18 Fix output of heater states 2016-07-28 17:40:01 -07:00
Scott Lahteine
8953e3e984 Allow Z_SAFE_HOMING without a probe 2016-07-27 04:33:56 -07:00
Scott Lahteine
5272147f7c Followup #4402 fixing 3-point leveling 2016-07-25 15:56:34 -07:00
Scott Lahteine
169c21b477 Merge pull request #4402 from thinkyhead/rc_consistent_positioning 
Account for coordinate space offsets
 2016-07-24 19:23:20 -07:00
Scott Lahteine
2595a40a61 Account for coordinate space more in G28 / G29 / M48 2016-07-24 18:34:05 -07:00
Scott Lahteine
b7b7c90477 Merge pull request #4389 from thinkyhead/rc_optimize_planner 
Optimize planner with precalculation, etc.
 2016-07-24 17:48:23 -07:00
Scott Lahteine
b183442c61 Fix inactive_extruder_x_pos for coordinate space 2016-07-24 17:20:36 -07:00
Scott Lahteine
f75b0c2ee1 Make POSITION macros global 2016-07-24 17:20:36 -07:00
Scott Lahteine
101b60ef42 Tweak Dual X Carriage data spacing 2016-07-24 17:20:35 -07:00
Scott Lahteine
d8f2876753 Replace some float division with multiplication 2016-07-24 13:27:50 -07:00
Scott Lahteine
f8b5749235 Replace division in planner with multiplication 2016-07-24 13:27:49 -07:00
Scott Lahteine
db5df9500b Move sync_plan_position closer to the top 2016-07-24 13:27:49 -07:00
João Brázio
50fb0f7cec M31 serial output is now always in EN 2016-07-24 15:52:03 +01:00
João Brázio
62d96d72f3 Renamed timestamp_t to duration_t 2016-07-24 03:16:02 +01:00
Scott Lahteine
bb93b6822a Use set_current_from_steppers_for_axis 2016-07-23 15:25:54 -07:00
AnHardt
96a162beda Use implications from #4370 in run_z_probe() 
See also https://github.com/MarlinFirmware/Marlin/pull/4370#issuecomment-234713680
 2016-07-23 13:09:28 -07:00
Scott Lahteine
4e67a85a5d Macros to loop over axes 2016-07-23 13:09:28 -07:00
esenapaj
784be56e99 Follow-up the PR #4353 (General cleanup: enum) 
・Update description of M111
 2016-07-24 00:53:35 +09:00
Scott Lahteine
08459a003f Undo the self-sabotage that is do_blocking_move_to_axis_pos 2016-07-23 00:59:11 -07:00