/* **************************************************************************
Marlin 3D Printer Firmware
Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see .
****************************************************************************/
/**
* Description: HAL for __AVR__
*/
#ifndef _HAL_AVR_H_
#define _HAL_AVR_H_
// --------------------------------------------------------------------------
// Includes
// --------------------------------------------------------------------------
#include "fastio.h"
#include
#include
#include
#include
#include
#include
#include
// --------------------------------------------------------------------------
// Defines
// --------------------------------------------------------------------------
//#define analogInputToDigitalPin(IO) IO
// Bracket code that shouldn't be interrupted
#ifndef CRITICAL_SECTION_START
#define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli();
#define CRITICAL_SECTION_END SREG = _sreg;
#endif
// --------------------------------------------------------------------------
// Types
// --------------------------------------------------------------------------
typedef uint16_t hal_timer_t;
#define HAL_TIMER_TYPE_MAX 0xFFFF
typedef int8_t pin_t;
#define HAL_SERVO_LIB Servo
// --------------------------------------------------------------------------
// Public Variables
// --------------------------------------------------------------------------
//extern uint8_t MCUSR;
// --------------------------------------------------------------------------
// Public functions
// --------------------------------------------------------------------------
//void cli(void);
//void _delay_ms(const int delay);
inline void HAL_clear_reset_source(void) { MCUSR = 0; }
inline uint8_t HAL_get_reset_source(void) { return MCUSR; }
// eeprom
//void eeprom_write_byte(unsigned char *pos, unsigned char value);
//unsigned char eeprom_read_byte(unsigned char *pos);
// timers
#define HAL_TIMER_RATE ((F_CPU) / 8) // i.e., 2MHz or 2.5MHz
#define STEP_TIMER_NUM 1
#define TEMP_TIMER_NUM 0
#define PULSE_TIMER_NUM TEMP_TIMER_NUM
#define HAL_STEPPER_TIMER_RATE HAL_TIMER_RATE
#define HAL_TICKS_PER_US ((HAL_STEPPER_TIMER_RATE) / 1000000) // Cannot be of type double
#define STEPPER_TIMER_PRESCALE 8
#define STEP_TIMER_MIN_INTERVAL 8 // minimum time in µs between stepper interrupts
#define TEMP_TIMER_FREQUENCY ((F_CPU) / 64.0 / 256.0)
#define TIMER_OCR_1 OCR1A
#define TIMER_COUNTER_1 TCNT1
#define TIMER_OCR_0 OCR0A
#define TIMER_COUNTER_0 TCNT0
#define PULSE_TIMER_PRESCALE 8
#define ENABLE_STEPPER_DRIVER_INTERRUPT() SBI(TIMSK1, OCIE1A)
#define DISABLE_STEPPER_DRIVER_INTERRUPT() CBI(TIMSK1, OCIE1A)
#define STEPPER_ISR_ENABLED() TEST(TIMSK1, OCIE1A)
#define ENABLE_TEMPERATURE_INTERRUPT() SBI(TIMSK0, OCIE0B)
#define DISABLE_TEMPERATURE_INTERRUPT() CBI(TIMSK0, OCIE0B)
#define TEMPERATURE_ISR_ENABLED() TEST(TIMSK0, OCIE0B)
#define HAL_timer_start(timer_num, frequency)
#define _CAT(a, ...) a ## __VA_ARGS__
#define HAL_timer_set_compare(timer, compare) (_CAT(TIMER_OCR_, timer) = compare)
#define HAL_timer_restrain(timer, interval_ticks) NOLESS(_CAT(TIMER_OCR_, timer), _CAT(TIMER_COUNTER_, timer) + interval_ticks)
#define HAL_timer_get_compare(timer) _CAT(TIMER_OCR_, timer)
#define HAL_timer_get_count(timer) _CAT(TIMER_COUNTER_, timer)
/**
* On AVR there is no hardware prioritization and preemption of
* interrupts, so this emulates it. The UART has first priority
* (otherwise, characters will be lost due to UART overflow).
* Then: Stepper, Endstops, Temperature, and -finally- all others.
*/
#define HAL_timer_isr_prologue(TIMER_NUM)
#define HAL_timer_isr_epilogue(TIMER_NUM)
/* 18 cycles maximum latency */
#define HAL_STEP_TIMER_ISR \
extern "C" void TIMER1_COMPA_vect (void) __attribute__ ((signal, naked, used, externally_visible)); \
extern "C" void TIMER1_COMPA_vect_bottom (void) asm ("TIMER1_COMPA_vect_bottom") __attribute__ ((used, externally_visible, noinline)); \
void TIMER1_COMPA_vect (void) { \
__asm__ __volatile__ ( \
A("push r16") /* 2 Save R16 */ \
A("in r16, __SREG__") /* 1 Get SREG */ \
A("push r16") /* 2 Save SREG into stack */ \
A("lds r16, %[timsk0]") /* 2 Load into R0 the Temperature timer Interrupt mask register */ \
A("push r16") /* 2 Save TIMSK0 into the stack */ \
A("andi r16,~%[msk0]") /* 1 Disable the temperature ISR */ \
A("sts %[timsk0], r16") /* 2 And set the new value */ \
A("lds r16, %[timsk1]") /* 2 Load into R0 the stepper timer Interrupt mask register [TIMSK1] */ \
A("andi r16,~%[msk1]") /* 1 Disable the stepper ISR */ \
A("sts %[timsk1], r16") /* 2 And set the new value */ \
A("sei") /* 1 Enable global interrupts - stepper and temperature ISRs are disabled, so no risk of reentry or being preempted by the temperature ISR */ \
A("push r16") /* 2 Save TIMSK1 into stack */ \
A("in r16, 0x3B") /* 1 Get RAMPZ register */ \
A("push r16") /* 2 Save RAMPZ into stack */ \
A("in r16, 0x3C") /* 1 Get EIND register */ \
A("push r0") /* C runtime can modify all the following registers without restoring them */ \
A("push r1") \
A("push r18") \
A("push r19") \
A("push r20") \
A("push r21") \
A("push r22") \
A("push r23") \
A("push r24") \
A("push r25") \
A("push r26") \
A("push r27") \
A("push r30") \
A("push r31") \
A("clr r1") /* C runtime expects this register to be 0 */ \
A("call TIMER1_COMPA_vect_bottom") /* Call the bottom handler - No inlining allowed, otherwise registers used are not saved */ \
A("pop r31") \
A("pop r30") \
A("pop r27") \
A("pop r26") \
A("pop r25") \
A("pop r24") \
A("pop r23") \
A("pop r22") \
A("pop r21") \
A("pop r20") \
A("pop r19") \
A("pop r18") \
A("pop r1") \
A("pop r0") \
A("out 0x3C, r16") /* 1 Restore EIND register */ \
A("pop r16") /* 2 Get the original RAMPZ register value */ \
A("out 0x3B, r16") /* 1 Restore RAMPZ register to its original value */ \
A("pop r16") /* 2 Get the original TIMSK1 value but with stepper ISR disabled */ \
A("ori r16,%[msk1]") /* 1 Reenable the stepper ISR */ \
A("cli") /* 1 Disable global interrupts - Reenabling Stepper ISR can reenter amd temperature can reenter, and we want that, if it happens, after this ISR has ended */ \
A("sts %[timsk1], r16") /* 2 And restore the old value - This reenables the stepper ISR */ \
A("pop r16") /* 2 Get the temperature timer Interrupt mask register [TIMSK0] */ \
A("sts %[timsk0], r16") /* 2 And restore the old value - This reenables the temperature ISR */ \
A("pop r16") /* 2 Get the old SREG value */ \
A("out __SREG__, r16") /* 1 And restore the SREG value */ \
A("pop r16") /* 2 Restore R16 value */ \
A("reti") /* 4 Return from interrupt */ \
: \
: [timsk0] "i" ((uint16_t)&TIMSK0), \
[timsk1] "i" ((uint16_t)&TIMSK1), \
[msk0] "M" ((uint8_t)(1< 7) ADCSRB = _BV(MUX5); else ADCSRB = 0; SET_ADMUX_ADCSRA(pin)
#else
#define HAL_START_ADC(pin) ADCSRB = 0; SET_ADMUX_ADCSRA(pin)
#endif
#define HAL_READ_ADC ADC
#define GET_PIN_MAP_PIN(index) index
#define GET_PIN_MAP_INDEX(pin) pin
#define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval)
#define HAL_SENSITIVE_PINS 0, 1
#endif // _HAL_AVR_H_