Firmware/Marlin/pins_TEENSYLU.h
2018-01-24 00:17:34 -06:00

163 lines
5.2 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Rev C 2 JUN 2017
*
* Converted to Arduino pin numbering
*/
/**
* There are two Arduino IDE extensions that are compatible with this board
* and with the mainstream Marlin software. All have been used with Arduino 1.6.12
*
* Teensyduino - http://www.pjrc.com/teensy/teensyduino.html
* Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu
*
* Installation instructions are at the above URL. Don't bother loading the
* libraries - they are not used with the Marlin software.
*
* Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support
* This is basically Teensyduino but with a bootloader that can handle image sizes
* larger than 64K.
*
* Installation:
*
* 1. Go to the above URL, click on the "Clone or Download" button and then
* click on "Download ZIP" button.
* 2. Unzip the file, find the "printrboard" directory and then copy it to the
* hardware directory in Arduino. The Arduino hardware directory will probably
* be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware.
* 3. Restart Arduino.
* 4. Select "Printrboard" from the 'Tools -> Boards' menu.
*
* Teensyduino is the most popular option. Printrboard is used if your board doesn't have
* the Teensyduino bootloader on it.
*/
/**
* To burn the bootloader that comes with Printrboard:
*
* 1. Connect your programmer to the board.
* 2. In the Arduino IDE select "Printrboard" and then select the programmer.
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
/**
* SILKSCREEN ERROR
*
* The silkscreen for the endstops do NOT match the schematic. The silkscreen SHOULD
* read (from left to right) X-STOP, Y-STOP, Z-STOP & E-STOP. The silkscreen actually
* reads E-STOP, X-STOP, Y-STOP & Z-STOP.
*
* The pin assignments in this file match the silkscreen.
*/
#if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__)
#error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Teensylu"
//
// Limit Switch definitions that match the SCHEMATIC
//
//#define X_STOP_PIN 25 // B5
//#define Y_STOP_PIN 26 // B6
//#define Z_STOP_PIN 27 // B7
//#define E_STOP_PIN 36 // E4
//
// Limit Switch definitions that match the SILKSCREEN
//
#define X_STOP_PIN 26 // B6
#define Y_STOP_PIN 27 // B7
#define Z_STOP_PIN 36 // E4
//#define E_STOP_PIN 25 // B5
//
// Steppers
//
#define X_STEP_PIN 28 // A0
#define X_DIR_PIN 29 // A1
#define X_ENABLE_PIN 19 // E7
#define Y_STEP_PIN 30 // A2
#define Y_DIR_PIN 31 // A3
#define Y_ENABLE_PIN 18 // E6
#define Z_STEP_PIN 32 // A4
#define Z_DIR_PIN 33 // A5
#define Z_ENABLE_PIN 17 // C7
#define E0_STEP_PIN 34 // A6
#define E0_DIR_PIN 35 // A7
#define E0_ENABLE_PIN 13 // C3
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (Extruder)
#define TEMP_BED_PIN 6 // Analog Input (Bed)
//
// Heaters / Fans
//
#define HEATER_0_PIN 15 // C5 PWM3B - Extruder
#define HEATER_BED_PIN 14 // C4 PWM3C
#define FAN_PIN 16 // C6 PWM3A
//
// Misc. Functions
//
#define SDSS 20 // B0 JP31-6
#define CASE_LIGHT_PIN 0 // D0 IO-14 PWM0B
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 3 // D3 IO-8
#define BTN_EN2 2 // D2 IO-10
#define BTN_ENC 41 // F3 IO-7
#define SDSS 38 // F0 IO-13 use SD card on Panelolu2
#endif
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 24 // B4 IO-3 PWM2A - MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 39 // F1 IO-11 - Pin should have a pullup!
#define SPINDLE_DIR_PIN 40 // F2 IO-9