Firmware/Marlin/pins_SANGUINOLOLU_11.h
2015-08-02 23:26:58 -05:00

175 lines
5.0 KiB
C

/**
* Sanguinololu board pin assignments
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 15
#define X_DIR_PIN 21
#define X_STOP_PIN 18
#define Y_STEP_PIN 22
#define Y_DIR_PIN 23
#define Y_STOP_PIN 19
#define Z_STEP_PIN 3
#define Z_DIR_PIN 2
#define Z_STOP_PIN 20
#define E0_STEP_PIN 1
#define E0_DIR_PIN 0
#define LED_PIN -1
#define FAN_PIN -1
#if MB(AZTEEG_X1) || MB(STB_11) || MB(MELZI)
#define FAN_PIN 4 // Works for Panelolu2 too
#if MB(MELZI)
#define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368.
#elif MB(STB_11)
#define LCD_PIN_BL 17 // LCD backlight LED
#endif
#endif
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
#define PS_ON_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN 13 // (extruder)
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#if ENABLED(SANGUINOLOLU_V_1_2)
#define HEATER_BED_PIN 12 // (bed)
#define X_ENABLE_PIN 14
#define Y_ENABLE_PIN 14
#define Z_ENABLE_PIN 26
#define E0_ENABLE_PIN 14
#if ENABLED(LCD_I2C_PANELOLU2)
#define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
#endif
#else
#define HEATER_BED_PIN 14 // (bed)
#define X_ENABLE_PIN -1
#define Y_ENABLE_PIN -1
#define Z_ENABLE_PIN -1
#define E0_ENABLE_PIN -1
#endif
#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define SDPOWER -1
#define SDSS 31
/**
* On some broken versions of the Sanguino libraries the pin definitions are wrong,
* which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368.
*/
//#define SDSS 24
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
// No buzzer installed
#define BEEPER_PIN -1
// LCD Pins
#if ENABLED(DOGLCD)
#if ENABLED(U8GLIB_ST7920) //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
#if MB(MELZI) // Melzi board
#define LCD_PINS_RS 30 //CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 29 //SID (MOSI)
#define LCD_PINS_D4 17 //SCK (CLK) clock
#define BEEPER_PIN 27 // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with Marlin so this can be used for BEEPER_PIN. You can use this pin with M42 instead of BEEPER_PIN.
#else // Sanguinololu 1.3
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif
#else // DOGM SPI LCD Support
#define DOGLCD_A0 30
#define DOGLCD_CS 29
#define LCD_CONTRAST 1
#endif
// Uncomment screen orientation
#define LCD_SCREEN_ROT_0
// #define LCD_SCREEN_ROT_90
// #define LCD_SCREEN_ROT_180
// #define LCD_SCREEN_ROT_270
#else // !DOGLCD - Standard Hitachi LCD controller
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif // !DOGLCD
//The encoder and click button
#define BTN_EN1 11
#define BTN_EN2 10
#if ENABLED(LCD_I2C_PANELOLU2)
#if MB(MELZI)
#define BTN_ENC 29
#define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi
#else
#define BTN_ENC 30
#endif
#else
#define BTN_ENC 16
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
#endif //Panelolu2
#define SD_DETECT_PIN -1
#elif ENABLED(MAKRPANEL)
#define BEEPER_PIN 29
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 30
#define DOGLCD_CS 17
#define LCD_PIN_BL 28 // backlight LED on PA3
// GLCD features
#define LCD_CONTRAST 1
// Uncomment screen orientation
#define LCD_SCREEN_ROT_0
// #define LCD_SCREEN_ROT_90
// #define LCD_SCREEN_ROT_180
// #define LCD_SCREEN_ROT_270
//The encoder and click button
#define BTN_EN1 11
#define BTN_EN2 10
#define BTN_ENC 16
#define SD_DETECT_PIN -1
#endif // MAKRPANEL
// #if FAN_PIN == 12 || FAN_PIN ==13
// #define FAN_SOFT_PWM
// #endif