Firmware2/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.h

328 lines
9.1 KiB
C
Raw Normal View History

/*
*******************************************************************************
* Copyright (c) 2017, STMicroelectronics
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#ifndef _VARIANT_ARDUINO_STM32_
#define _VARIANT_ARDUINO_STM32_
/*----------------------------------------------------------------------------
* Headers
*----------------------------------------------------------------------------*/
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
/*----------------------------------------------------------------------------
* Pins
*----------------------------------------------------------------------------*/
#if defined(ARDUINO_STEVAL)
/*----------------------------------------------------------------------------
* Pins
*----------------------------------------------------------------------------*/
// USART1_MAIN
#define PA9 0 //TX
#define PA10 1 //RX
// WIFI (USART2)
#define PD3 2 // CTS
#define PD4 3 // RTS
#define PD5 4 // TX
#define PD6 5 // RX
#define PB5 6 // WIFI_WAKEUP
#define PE11 7 // WIFI_RESET
#define PE12 8 // WIFI_BOOT
// STATUS_LED
#define PE1 9 // STATUS_LED
// SPI USER
#define PB12 10 // SPI_CS
#define PB15 11 // SPI_MOSI
#define PB14 12 // SPI_MISO
#define PB13 13 // SPI_SCK
// I2C USER
#define PB7 14 // SDA
#define PB6 15 // SCL
// SPI
#define PA4 16 // SPI_CS
#define PA5 17 // SPI_SCK
#define PA6 18 // SPI_MISO
#define PA7 19 // SPI_MOSI
// JTAG
#define PA13 20 // JTAG_TMS/SWDIO
#define PA14 21 // JTAG_TCK/SWCLK
#define PB3 22 // JTAG_TDO/SWO
// SDCARD
#define PC8 23 // SDIO_D0
#define PC9 24 // SDIO_D1
#define PA15 25 // SD_CARD_DETECT
#define PC10 26 // SDIO_D2
#define PC11 27 // SDIO_D3
#define PC12 28 // SDIO_CK
#define PD2 29 // SDIO_CMD
// OTG
#define PA11 30 //OTG_DM
#define PA12 31 //OTG_DP
// IR/PROBE
#define PD1 32 //IR_OUT
#define PC1 33 //IR_ON
// USER_PINS
#define PD7 34 // USER3
#define PB9 35 // USER1
#define PE0 36 // USER2
#define PB4 37 // USER4
// USERKET
#define PE7 38 // USER_BUTTON
// ENDSTOPS
#define PD8 39 // X_STOP
#define PD9 40 // Y_STOP
#define PD10 41 // Z_STOP
#define PD11 42 // U_STOP
#define PA8 43 // V_STOP
#define PD0 44 // W_STOP
// HEATERS
#define PD13 45 // BED_HEAT_2
#define PD14 46 // BED_HEAT_1
#define PD15 47 // BED_HEAT_3
#define PC7 48 // E1_HEAT_PWM
#define PB0 49 // E2_HEAT_PWM
#define PB1 50 // E3_HEAT_PWM
// THERMISTOR
#define PC2 51 // BED_THERMISTOR_1
#define PC3 52 // BED_THERMISTOR_2
#define PA3 53 // BED_THERMISTOR_3
#define PA0 54 // E1_THERMISTOR
#define PA1 55 // E2_THERMISTOR
#define PA2 56 // E3_THERMISTOR
// FANS
#define PC4 57 // E1_FAN
#define PC5 58 // E2_FAN
#define PE8 59 // E3_FAN
// X_MOTOR
#define PE13 60 // X_RESET
#define PE14 61 // X_PWM
#define PE15 62 // X_DIR
// Y_MOTOR
#define PE10 63 // Y_RESET
#define PB10 64 // Y_PWM
#define PE9 65 // Y_DIR
// Z_MOTOR
#define PC15 66 // Z_RESET
#define PC6 67 // Z_PWM
#define PC0 68 // Z_DIR
// E1_MOTOR
#define PC14 69 // E1_RESET
#define PC13 70 // E1_DIR
#define PD12 71 // E1_PWM
// E2_MOTOR
#define PE4 72 // E2_RESET
#define PE5 73 // E2_PWM
#define PE6 74 // E2_DIR
// E3_MOTOR
#define PE3 75 // E3_RESET
#define PE2 76 // E3_DIR
#define PB8 77 // E3_PWM
// This must be a literal
#define NUM_DIGITAL_PINS 78
// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
#define NUM_ANALOG_INPUTS 6
#define NUM_ANALOG_FIRST 51
// On-board LED pin number
#define LED_BUILTIN PE1
#define LED_GREEN LED_BUILTIN
// On-board user button
#define USER_BTN PE7
// UART Definitions
#define SERIAL_UART_INSTANCE 1 // Connected to ST-Link
//#define SERIAL_UART_INSTANCE 2 // Connected to WIFI
// Default pin used for 'Serial' instance (ex: ST-Link)
// Mandatory for Firmata
#if SERIAL_UART_INSTANCE == 1 // ST-Link & J23
#define PIN_SERIAL_RX PA10
#define PIN_SERIAL_TX PA9
#elif SERIAL_UART_INSTANCE == 2 // WIFI interface
#define PIN_SERIAL2_RX PD6
#define PIN_SERIAL2_TX PD5
#else
#error'Invaqlid setting for SERIAL_UART_INSTANCE'
#endif
// Timer Definitions
#define TIMER_SERVO TIM4 // TIMER_SERVO must be defined in this file
#define TIMER_TONE TIM5 // TIMER_TONE must be defined in this file
/* SD detect signal */
/*
* By default, R67 is not provided, so SD card detect is not used.
* Note: SD CD (pin 16 of expansion connector J23) can be connected
* to GND in order to be able to use SD_DETECT_PIN
*/
/*#define SD_DETECT_PIN PA15*/
/* HAL configuration */
#define HSE_VALUE 25000000U
/* Extra HAL modules */
#define HAL_SD_MODULE_ENABLED
#endif
#ifdef __cplusplus
} // extern "C"
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
#ifdef __cplusplus
// These serial port names are intended to allow libraries and architecture-neutral
// sketches to automatically default to the correct port name for a particular type
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
//
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
//
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
//
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
//
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
//
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
// pins are NOT connected to anything by default.
#define SERIAL_PORT_MONITOR Serial
#define SERIAL_PORT_HARDWARE Serial1
#endif
#endif // _VARIANT_ARDUINO_STM32_
// PA0 54 // E1_THERMISTOR
// PA1 55 // E2_THERMISTOR
// PA2 56 // E3_THERMISTOR
// PA3 53 // BED_THERMISTOR_3
// PA4 16 // SPI_CS
// PA5 17 // SPI_SCK
// PA6 18 // SPI_MISO
// PA7 19 // SPI_MOSI
// PA8 43 // V_STOP
// PA9 0 //TX
// PA10 1 //RX
// PA11 30 //OTG_DM
// PA12 31 //OTG_DP
// PA13 20 // JTAG_TMS/SWDIO
// PA14 21 // JTAG_TCK/SWCLK
// PA15 25 // SD_CARD_DETECT
// PB0 49 // E2_HEAT_PWM
// PB1 50 // E3_HEAT_PWM
// PB3 22 // JTAG_TDO/SWO
// PB4 37 // USER4
// PB5 6 // WIFI_WAKEUP
// PB6 15 // SCL
// PB7 14 // SDA
// PB8 77 // E3_PWM
// PB9 35 // USER1
// PB10 64 // Y_PWM
// PB12 10 // SPI_CS
// PB13 13 // SPI_SCK
// PB14 12 // SPI_MISO
// PB15 11 // SPI_MOSI
// PC0 68 // Z_DIR
// PC1 33 //IR_ON
// PC2 51 // BED_THERMISTOR_1
// PC3 52 // BED_THERMISTOR_2
// PC4 57 // E1_FAN
// PC5 58 // E2_FAN
// PC6 67 // Z_PWM
// PC7 48 // E1_HEAT_PWM
// PC8 23 // SDIO_D0
// PC9 24 // SDIO_D1
// PC10 26 // SDIO_D2
// PC11 27 // SDIO_D3
// PC12 28 // SDIO_CK
// PC13 70 // E1_DIR
// PC14 69 // E1_RESET
// PC15 66 // Z_RESET
// PD0 44 // W_STOP
// PD1 32 //IR_OUT
// PD2 29 // SDIO_CMD
// PD3 2 // CTS
// PD4 3 // RTS
// PD5 4 // TX
// PD6 5 // RX
// PD7 34 // USER3
// PD8 39 // X_STOP
// PD9 40 // Y_STOP
// PD10 41 // Z_STOP
// PD11 42 // U_STOP
// PD12 71 // E1_PWM
// PD13 45 // BED_HEAT_2
// PD14 46 // BED_HEAT_1
// PD15 47 // BED_HEAT_3
// PE0 36 // USER2
// PE1 9 // STATUS_LED
// PE2 76 // E3_DIR
// PE3 75 // E3_RESET
// PE4 72 // E2_RESET
// PE5 73 // E2_PWM
// PE6 74 // E2_DIR
// PE7 38 // USER_BUTTON
// PE8 59 // E3_FAN
// PE9 65 // Y_DIR
// PE10 63 // Y_RESET
// PE11 7 // WIFI_RESET
// PE12 8 // WIFI_BOOT
// PE13 60 // X_RESET
// PE14 61 // X_PWM
// PE15 62 // X_DIR