140 lines
3.2 KiB
C
140 lines
3.2 KiB
C
|
/**
|
||
|
|
* Marlin 3D Printer Firmware
|
||
|
|
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
*
|
||
|
|
* Based on Sprinter and grbl.
|
||
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
|
*
|
||
|
|
* This program is free software: you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License as published by
|
||
|
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
|
* (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef TARGET_STM32F1
|
||
|
|
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifndef BOARD_NAME
|
||
|
|
#define BOARD_NAME "BIGTREE SKR MINI E3"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
// Release PB3/PB4 (E0 STP/DIR) from JTAG pins
|
||
|
|
#define DISABLE_JTAG
|
||
|
|
|
||
|
|
// Ignore temp readings during develpment.
|
||
|
|
//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
|
||
|
|
|
||
|
|
//
|
||
|
|
// Servos
|
||
|
|
//
|
||
|
|
#define SERVO0_PIN PA1
|
||
|
|
|
||
|
|
//
|
||
|
|
// Limit Switches
|
||
|
|
//
|
||
|
|
#define X_STOP_PIN PC0
|
||
|
|
#define Y_STOP_PIN PC1
|
||
|
|
#define Z_STOP_PIN PC2
|
||
|
|
|
||
|
|
//
|
||
|
|
// Z Probe must be this pins
|
||
|
|
//
|
||
|
|
#define Z_MIN_PROBE_PIN PC14
|
||
|
|
|
||
|
|
//
|
||
|
|
// Filament Runout Sensor
|
||
|
|
//
|
||
|
|
#ifndef FIL_RUNOUT_PIN
|
||
|
|
#define FIL_RUNOUT_PIN PC15
|
||
|
|
#endif
|
||
|
|
|
||
|
|
//
|
||
|
|
// Steppers
|
||
|
|
//
|
||
|
|
#define X_ENABLE_PIN PB14
|
||
|
|
#define X_STEP_PIN PB13
|
||
|
|
#define X_DIR_PIN PB12
|
||
|
|
|
||
|
|
#define Y_ENABLE_PIN PB11
|
||
|
|
#define Y_STEP_PIN PB10
|
||
|
|
#define Y_DIR_PIN PB2
|
||
|
|
|
||
|
|
#define Z_ENABLE_PIN PB1
|
||
|
|
#define Z_STEP_PIN PB0
|
||
|
|
#define Z_DIR_PIN PC5
|
||
|
|
|
||
|
|
#define E0_ENABLE_PIN PD2
|
||
|
|
#define E0_STEP_PIN PB3
|
||
|
|
#define E0_DIR_PIN PB4
|
||
|
|
|
||
|
|
#if HAS_DRIVER(TMC2209)
|
||
|
|
/**
|
||
|
|
* TMC2209 stepper drivers
|
||
|
|
* Hardware serial communication ports.
|
||
|
|
*/
|
||
|
|
#define X_HARDWARE_SERIAL Serial4
|
||
|
|
#define Y_HARDWARE_SERIAL Serial4
|
||
|
|
#define Z_HARDWARE_SERIAL Serial4
|
||
|
|
#define E0_HARDWARE_SERIAL Serial4
|
||
|
|
#endif
|
||
|
|
|
||
|
|
//
|
||
|
|
// Temperature Sensors
|
||
|
|
//
|
||
|
|
#define TEMP_0_PIN PA0 // Analog Input
|
||
|
|
#define TEMP_BED_PIN PC3 // Analog Input
|
||
|
|
|
||
|
|
//
|
||
|
|
// Heaters / Fans
|
||
|
|
//
|
||
|
|
#define HEATER_0_PIN PC8 // EXTRUDER
|
||
|
|
#define HEATER_BED_PIN PC9 // BED
|
||
|
|
#define FAN_PIN PA8
|
||
|
|
|
||
|
|
//
|
||
|
|
// USB connect control
|
||
|
|
//
|
||
|
|
#define USB_CONNECT PC13
|
||
|
|
#define USB_CONNECT_INVERTING false
|
||
|
|
|
||
|
|
#define SD_DETECT_PIN PC4
|
||
|
|
|
||
|
|
/**
|
||
|
|
* _____
|
||
|
|
* 5V | · · | GND
|
||
|
|
* (LCD_EN) PB7 | · · | PB8 (LCD_RS)
|
||
|
|
* (LCD_D4) PB9 | · · | PA10 (BTN_EN2)
|
||
|
|
* RESET | · · | PA9 (BTN_EN1)
|
||
|
|
* (BTN_ENC) PB6 | · · | PB5 (BEEPER)
|
||
|
|
* -----
|
||
|
|
* EXP1
|
||
|
|
*/
|
||
|
|
#if HAS_SPI_LCD
|
||
|
|
#define BEEPER_PIN PB5
|
||
|
|
#define BTN_ENC PB6
|
||
|
|
|
||
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
||
|
|
#define LCD_PINS_RS PB8
|
||
|
|
|
||
|
|
#define BTN_EN1 PA9
|
||
|
|
#define BTN_EN2 PA10
|
||
|
|
|
||
|
|
#define LCD_PINS_ENABLE PB7
|
||
|
|
#define LCD_PINS_D4 PB9
|
||
|
|
|
||
|
|
#else
|
||
|
|
#error "Only CR10_STOCKDISPLAY is currently supported on the BIGTREE_SKR_MINI_E3."
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#endif // HAS_SPI_LCD
|