Firmware2/Marlin/src/HAL/DUE/watchdog.cpp

115 lines
3.7 KiB
C++
Raw Normal View History

2017-07-19 01:29:06 +02:00
/**
* Marlin 3D Printer Firmware
2020-02-03 15:00:57 +01:00
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
2017-07-19 01:29:06 +02:00
*
* Based on Sprinter and grbl.
2019-06-28 06:57:50 +02:00
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
2017-07-19 01:29:06 +02:00
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
2020-07-23 05:20:14 +02:00
* along with this program. If not, see <https://www.gnu.org/licenses/>.
2017-07-19 01:29:06 +02:00
*
*/
#ifdef ARDUINO_ARCH_SAM
2017-09-27 11:57:33 +02:00
2017-09-06 13:28:32 +02:00
#include "../../inc/MarlinConfig.h"
#include "../../MarlinCore.h"
2019-09-03 02:49:58 +02:00
#include "watchdog.h"
2017-07-19 01:29:06 +02:00
// Override Arduino runtime to either config or disable the watchdog
//
// We need to configure the watchdog as soon as possible in the boot
// process, because watchdog initialization at hardware reset on SAM3X8E
// is unreliable, and there is risk of unintended resets if we delay
// that initialization to a later time.
2019-09-17 03:31:08 +02:00
void watchdogSetup() {
2017-07-19 01:29:06 +02:00
#if ENABLED(USE_WATCHDOG)
2017-07-19 01:29:06 +02:00
// 4 seconds timeout
uint32_t timeout = 4000;
// Calculate timeout value in WDT counter ticks: This assumes
// the slow clock is running at 32.768 kHz watchdog
// frequency is therefore 32768 / 128 = 256 Hz
timeout = (timeout << 8) / 1000;
if (timeout == 0)
timeout = 1;
else if (timeout > 0xFFF)
timeout = 0xFFF;
// We want to enable the watchdog with the specified timeout
uint32_t value =
WDT_MR_WDV(timeout) | // With the specified timeout
WDT_MR_WDD(timeout) | // and no invalid write window
#if !(SAMV70 || SAMV71 || SAME70 || SAMS70)
WDT_MR_WDRPROC | // WDT fault resets processor only - We want
// to keep PIO controller state
#endif
WDT_MR_WDDBGHLT | // WDT stops in debug state.
WDT_MR_WDIDLEHLT; // WDT stops in idle state.
#if ENABLED(WATCHDOG_RESET_MANUAL)
// We enable the watchdog timer, but only for the interrupt.
// Configure WDT to only trigger an interrupt
value |= WDT_MR_WDFIEN; // Enable WDT fault interrupt.
// Disable WDT interrupt (just in case, to avoid triggering it!)
NVIC_DisableIRQ(WDT_IRQn);
// We NEED memory barriers to ensure Interrupts are actually disabled!
// ( https://dzone.com/articles/nvic-disabling-interrupts-on-arm-cortex-m-and-the )
__DSB();
__ISB();
// Initialize WDT with the given parameters
WDT_Enable(WDT, value);
// Configure and enable WDT interrupt.
NVIC_ClearPendingIRQ(WDT_IRQn);
NVIC_SetPriority(WDT_IRQn, 0); // Use highest priority, so we detect all kinds of lockups
NVIC_EnableIRQ(WDT_IRQn);
2017-07-19 01:29:06 +02:00
#else
2017-07-19 01:29:06 +02:00
// a WDT fault triggers a reset
value |= WDT_MR_WDRSTEN;
// Initialize WDT with the given parameters
WDT_Enable(WDT, value);
#endif
// Reset the watchdog
WDT_Restart(WDT);
#else
// Make sure to completely disable the Watchdog
WDT_Disable(WDT);
#endif
}
#if ENABLED(USE_WATCHDOG)
// Initialize watchdog - On SAM3X, Watchdog was already configured
// and enabled or disabled at startup, so no need to reconfigure it
// here.
2019-09-17 03:31:08 +02:00
void watchdog_init() {
// Reset watchdog to start clean
WDT_Restart(WDT);
}
2017-07-19 01:29:06 +02:00
#endif // USE_WATCHDOG
#endif