Firmware2/Marlin/pins_GEN6.h

120 lines
3.1 KiB
C
Raw Normal View History

/**
2016-03-24 19:01:20 +01:00
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Gen6 pin assignments
*/
2017-04-07 20:52:21 +02:00
/**
* Rev B 26 DEC 2016
*
* 1) added pointer to a current Arduino IDE extension
* 2) added support for M3, M4 & M5 spindle control commands
* 3) added case light pin definition
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
2017-08-24 01:23:19 +02:00
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "Gen6"
#endif
//
// Limit Switches
//
#define X_STOP_PIN 20
#define Y_STOP_PIN 25
#define Z_STOP_PIN 30
//
// Steppers
//
#define X_STEP_PIN 15
#define X_DIR_PIN 18
#define X_ENABLE_PIN 19
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Z_STEP_PIN 27
#define Z_DIR_PIN 28
#define Z_ENABLE_PIN 29
#define E0_STEP_PIN 4 // Edited @ EJE Electronics 20100715
#define E0_DIR_PIN 2 // Edited @ EJE Electronics 20100715
#define E0_ENABLE_PIN 3 // Added @ EJE Electronics 20100715
//
// Temperature Sensor
//
#define TEMP_0_PIN 5 // Analog Input
//
// Heaters
//
#define HEATER_0_PIN 14 // changed @ rkoeppl 20110410
#if !MB(GEN6)
#define HEATER_BED_PIN 1 // changed @ rkoeppl 20110410
#define TEMP_BED_PIN 0 // Analog Input
#endif
//
// Misc. Functions
//
#define SDSS 17
#define DEBUG_PIN 0
2017-06-09 01:08:03 +02:00
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
// RS485 pins
#define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13
2017-04-07 20:52:21 +02:00
//
// M3/M4/M5 - Spindle/Laser Control
//
2017-06-09 01:08:03 +02:00
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
2017-04-07 20:52:21 +02:00
#define SPINDLE_DIR_PIN 6