Firmware2/Marlin/src/pins/pins_AZSMZ_MINI.h

144 lines
3.4 KiB
C
Raw Normal View History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* AZSMZ MINI pin assignments
*/
//#if !defined(TARGET_LPC1768)
#if DISABLED(IS_REARM)
#error "Oops! Make sure you have Re-Arm selected."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "AZSMZ MINI"
#endif
#define LARGE_FLASH true
//
// Servos
//
#define SERVO0_PIN 53
2017-10-27 06:33:43 +02:00
//
// Limit Switches
//
#define X_MIN_PIN 3
#define Y_MIN_PIN 14
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19
//
// Steppers
//
#define X_STEP_PIN 26
#define X_DIR_PIN 28
#define X_ENABLE_PIN 24
#define Y_STEP_PIN 54
#define Y_DIR_PIN 55
#define Y_ENABLE_PIN 38
#define Z_STEP_PIN 60
#define Z_DIR_PIN 61
#define Z_ENABLE_PIN 56
#define E0_STEP_PIN 46
#define E0_DIR_PIN 48
#define E0_ENABLE_PIN 62
#define E1_STEP_PIN 36
#define E1_DIR_PIN 34
#define E1_ENABLE_PIN 30
//
// Temperature Sensors
// 3.3V max when defined as an analog input
//
#define TEMP_0_PIN 0 // A0 (TH1)
#define TEMP_BED_PIN 1 // A1 (TH2)
#define TEMP_1_PIN 2 // A2 (TH3)
//
// Heaters / Fans
//
// EFB
#define HEATER_0_PIN 8
#define HEATER_BED_PIN 10
#define FAN_PIN 9
#define FAN1_PIN 63
#if ENABLED(AZSMZ_12864)
#define BEEPER_PIN 37
#define DOGLCD_A0 59
#define DOGLCD_CS 41
#define BTN_EN1 13
#define BTN_EN2 15
#define BTN_ENC 31
#define LCD_SDSS 16
#define SD_DETECT_PIN 33
#endif
//
// Ethernet pins
//
#define ENET_MDIO 71
#define ENET_RX_ER 73
#define ENET_RXD1 75
#define ENET_MOC 70
#define REF_CLK 72
#define ENET_RXD0 74
#define ENET_CRS 76
#define ENET_TX_EN 77
#define ENET_TXD0 78
#define ENET_TXD1 79
/**
* PWMs
*
* There are 6 PWMs. Each PWM can be assigned to one of two pins.
*
* SERVO2 does NOT have a PWM assigned to it.
*
* PWM1.1 DIO4 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM
* PWM1.1 DIO26 E0_STEP_PIN
* PWM1.2 DIO11 SERVO0_PIN
* PWM1.2 DIO54 X_STEP_PIN
* PWM1.3 DIO6 SERVO1_PIN J5-1
* PWM1.3 DIO60 Y_STEP_PIN
* PWM1.4 DIO53 SDSS(SSEL0) J3-5 AUX-3
* PWM1.4 DIO46 Z_STEP_PIN
* PWM1.5 DIO3 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.5 DIO9 RAMPS_D9_PIN
* PWM1.6 DIO14 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
* PWM1.6 DIO10 RAMPS_D10_PIN
*/
/**
* Special pins
* D37 - not 5V tolerant
* D49 - not 5V tolerant
* D57 - open collector
* D58 - open collector
*/