Firmware2/Marlin/pins_PRINTRBOARD.h

113 lines
3.2 KiB
C
Raw Normal View History

/**
* Printrboard pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
* http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
*/
#ifndef __AVR_AT90USB1286__
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif
#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
#error These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h
#endif
#define LARGE_FLASH true
#define X_STEP_PIN 0
#define X_DIR_PIN 1
#define X_ENABLE_PIN 39
#define Y_STEP_PIN 2
#define Y_DIR_PIN 3
#define Y_ENABLE_PIN 38
#define Z_STEP_PIN 4
#define Z_DIR_PIN 5
#define Z_ENABLE_PIN 23
#define E0_STEP_PIN 6
#define E0_DIR_PIN 7
#define E0_ENABLE_PIN 19
#define HEATER_0_PIN 21 // Extruder
#define HEATER_1_PIN 46
#define HEATER_2_PIN 47
#define HEATER_BED_PIN 20
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
// fastio pin numbering otherwise
#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN)
#define FAN_PIN 22
#else
#define FAN_PIN 16
#endif
#define X_STOP_PIN 35
#if ENABLED(SDSUPPORT)
#define Y_STOP_PIN 37 // Move Ystop to Estop socket
#else
#define Y_STOP_PIN 8 // Ystop in Ystop socket
#endif
#define Z_STOP_PIN 36
#define TEMP_0_PIN 1 // Extruder / Analog pin numbering
#define TEMP_BED_PIN 0 // Bed / Analog pin numbering
#if ENABLED(FILAMENT_SENSOR)
#define FILWIDTH_PIN 2
#endif
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
////LCD Pin Setup////
#define SDPOWER -1
#define SDSS 8
#define LED_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1
#if DISABLED(SDSUPPORT)
// these pins are defined in the SD library if building with SD support
#define SCK_PIN 9
#define MISO_PIN 11
#define MOSI_PIN 10
#endif
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
//we have no buzzer installed
#define BEEPER_PIN -1
//LCD Pins
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
#define BTN_EN2 26 //TX1 - fastio.h pin mapping 26
#define BTN_ENC 43 //A3 - fastio.h pin mapping 43
#define SDSS 40 //use SD card on Panelolu2 (Teensyduino pin mapping)
#endif // LCD_I2C_PANELOLU2
//not connected to a pin
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER_PIN 32 //FastIO
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 42 //Non-FastIO
#define DOGLCD_CS 43 //Non-FastIO
#define LCD_SCREEN_ROT_180
//The encoder and click button (FastIO Pins)
#define BTN_EN1 26
#define BTN_EN2 27
#define BTN_ENC 47 //the click switch
#define SDSS 45
#define SD_DETECT_PIN -1 // FastIO (Manual says 72 I'm not certain cause I can't test)
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 12 //Non-FastIO
#define STAT_LED_BLUE 10 //Non-FastIO
#endif
#endif