2015-07-09 00:08:15 +02:00
# ifndef CONFIGURATION_H
# define CONFIGURATION_H
# include "boards.h"
2015-07-23 00:39:23 +02:00
# include "macros.h"
2015-07-09 00:08:15 +02:00
//===========================================================================
//============================= Getting Started =============================
//===========================================================================
/*
Here are some standard links for getting your machine calibrated :
* http : //reprap.org/wiki/Calibration
* http : //youtu.be/wAL9d7FgInk
* http : //calculator.josefprusa.cz
* http : //reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
* http : //www.thingiverse.com/thing:5573
* https : //sites.google.com/site/repraplogphase/calibration-of-your-reprap
* http : //www.thingiverse.com/thing:298812
*/
// This configuration file contains the basic settings.
// Advanced settings can be found in Configuration_adv.h
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
//===========================================================================
//============================= DELTA Printer ===============================
//===========================================================================
// For a Delta printer replace the configuration files with the files in the
// example_configurations/delta directory.
//
//===========================================================================
//============================= SCARA Printer ===============================
//===========================================================================
// For a Scara printer replace the configuration files with the files in the
// example_configurations/SCARA directory.
//
// @section info
2015-08-01 16:57:59 +02:00
# if ENABLED(USE_AUTOMATIC_VERSIONING)
2015-07-09 00:08:15 +02:00
# include "_Version.h"
# else
# include "Default_Version.h"
# endif
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
// build by the user have been successfully uploaded into firmware.
# define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
2015-07-31 23:43:01 +02:00
# define SHOW_BOOTSCREEN
2015-08-01 17:03:46 +02:00
# define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
2015-07-09 00:08:15 +02:00
//#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
// @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host.
// This allows the connection of wireless adapters (for instance) to non-default port pins.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
// :[0,1,2,3,4,5,6,7]
# define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
# define BAUDRATE 115200
2015-08-01 01:55:47 +02:00
// Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH
2015-07-09 00:08:15 +02:00
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
# ifndef MOTHERBOARD
# define MOTHERBOARD BOARD_RIGIDBOARD
# endif
// Optional custom name for your RepStrap or other custom machine
// Displayed in the LCD "Ready" message
2015-09-15 19:36:08 +02:00
//#define CUSTOM_MACHINE_NAME "3D Printer"
2015-07-09 00:08:15 +02:00
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
2015-09-15 19:36:08 +02:00
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
2015-07-09 00:08:15 +02:00
// This defines the number of extruders
// :[1,2,3,4]
2015-08-02 01:35:07 +02:00
# define EXTRUDERS 1 // Single extruder. Set to 2 for dual extruders
2015-07-09 00:08:15 +02:00
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
# define EXTRUDER_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis
# define EXTRUDER_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup
// 1 = ATX
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
// :{1:'ATX',2:'X-Box 360'}
# define POWER_SUPPLY 1
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
//#define PS_DEFAULT_OFF
// @section temperature
//===========================================================================
//============================= Thermal Settings ============================
//===========================================================================
//
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
//
//// Temperature sensor settings:
// -2 is thermocouple with MAX6675 (only for sensor 0)
// -1 is thermocouple with AD595
// 0 is not used
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
// 3 is Mendel-parts thermistor (4.7k pullup)
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
// 20 is the PT100 circuit found in the Ultimainboard V2.x
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
//
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
// (but gives greater accuracy and more stable PID)
// 51 is 100k thermistor - EPCOS (1k pullup)
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
//
// 1047 is Pt1000 with 4k7 pullup
// 1010 is Pt1000 with 1k pullup (non standard)
// 147 is Pt100 with 4k7 pullup
// 110 is Pt100 with 1k pullup (non standard)
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
// Use it for Testing or Development purposes. NEVER for production machine.
2015-09-15 19:36:08 +02:00
//#define DUMMY_THERMISTOR_998_VALUE 25
//#define DUMMY_THERMISTOR_999_VALUE 100
2015-07-09 00:08:15 +02:00
// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
2015-08-02 01:35:07 +02:00
# define TEMP_SENSOR_0 1 // DGlass3D = 5; RigidBot = 1; 3DSv6 = 5
# define TEMP_SENSOR_1 0
2015-07-09 00:08:15 +02:00
# define TEMP_SENSOR_2 0
# define TEMP_SENSOR_3 0
2015-08-02 01:35:07 +02:00
# define TEMP_SENSOR_BED 1
2015-07-09 00:08:15 +02:00
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
//#define TEMP_SENSOR_1_AS_REDUNDANT
//#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Actual temperature must be close to target for this long before M109 returns success
# define TEMP_RESIDENCY_TIME 10 // (seconds)
# define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
# define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
# define HEATER_0_MINTEMP 5
# define HEATER_1_MINTEMP 5
# define HEATER_2_MINTEMP 5
# define HEATER_3_MINTEMP 5
# define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
# define HEATER_0_MAXTEMP 275
# define HEATER_1_MAXTEMP 275
# define HEATER_2_MAXTEMP 275
# define HEATER_3_MAXTEMP 275
# define BED_MAXTEMP 150
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
2016-03-06 11:01:29 +01:00
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R
//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R
2015-07-09 00:08:15 +02:00
//===========================================================================
//============================= PID Settings ================================
//===========================================================================
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
// Comment the following line to disable PID and enable bang-bang.
# define PIDTEMP
# define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
# define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
2015-07-23 03:23:23 +02:00
# if ENABLED(PIDTEMP)
2015-07-09 00:08:15 +02:00
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with gcode: M301 E[extruder number, 0-2]
# define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
# define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
# define K1 0.95 //smoothing factor within the PID
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
2015-08-02 01:35:07 +02:00
// Rigidbot hotend
# define DEFAULT_Kp 16.17
# define DEFAULT_Ki 0.85
# define DEFAULT_Kd 76.55
// Base DGlass3D/E3Dv6 hotend
2015-09-15 19:36:08 +02:00
//#define DEFAULT_Kp 10
//#define DEFAULT_Ki 0.85
//#define DEFAULT_Kd 245
2015-07-09 00:08:15 +02:00
2015-12-13 02:57:36 +01:00
// E3D w/ rigidbot cartridge
//#define DEFAULT_Kp 16.30
//#define DEFAULT_Ki 0.95
//#define DEFAULT_Kd 69.69
2015-07-09 00:08:15 +02:00
# endif // PIDTEMP
//===========================================================================
//============================= PID > Bed Temperature Control ===============
//===========================================================================
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
//
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
// shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below.
//#define PIDTEMPBED
//#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
# define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
//#define PID_BED_DEBUG // Sends debug data to the serial port.
2015-07-23 03:23:23 +02:00
# if ENABLED(PIDTEMPBED)
2015-07-09 00:08:15 +02:00
# define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
//RigidBot, from pid autotune
# define DEFAULT_bedKp 355
# define DEFAULT_bedKi 66.5
# define DEFAULT_bedKd 480
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
# endif // PIDTEMPBED
// @section extruder
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
# define PREVENT_DANGEROUS_EXTRUDE
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
# define PREVENT_LENGTHY_EXTRUDE
# define EXTRUDE_MINTEMP 170
# define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//===========================================================================
//======================== Thermal Runaway Protection =======================
//===========================================================================
/**
* Thermal Runaway Protection protects your printer from damage and fire if a
* thermistor falls out or temperature sensors fail in any way .
*
* The issue : If a thermistor falls out or a temperature sensor fails ,
* Marlin can no longer sense the actual temperature . Since a disconnected
* thermistor reads as a low temperature , the firmware will keep the heater on .
*
* The solution : Once the temperature reaches the target , start observing .
* If the temperature stays too far below the target ( hysteresis ) for too long ,
* the firmware will halt as a safety precaution .
*/
# define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
# define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
//===========================================================================
//============================= Mechanical Settings =========================
//===========================================================================
// @section machine
// Uncomment this option to enable CoreXY kinematics
2015-08-02 01:35:07 +02:00
//#define COREXY
2015-07-09 00:08:15 +02:00
2016-03-07 14:03:33 +01:00
// Uncomment this option to enable CoreXZ kinematics
//#define COREXZ
2015-07-09 00:08:15 +02:00
// Enable this option for Toshiba steppers
//#define CONFIG_STEPPERS_TOSHIBA
// @section homing
// coarse Endstop Settings
# define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
2015-08-02 01:35:07 +02:00
# if DISABLED(ENDSTOPPULLUPS)
2015-07-09 00:08:15 +02:00
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
2015-09-15 19:36:08 +02:00
//#define ENDSTOPPULLUP_XMAX
//#define ENDSTOPPULLUP_YMAX
//#define ENDSTOPPULLUP_ZMAX
//#define ENDSTOPPULLUP_XMIN
//#define ENDSTOPPULLUP_YMIN
//#define ENDSTOPPULLUP_ZMIN
//#define ENDSTOPPULLUP_ZMIN_PROBE
2015-07-09 00:08:15 +02:00
# endif
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = true ; // set to true to invert the logic of the endstop.
2015-08-10 10:35:39 +02:00
const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false ; // set to true to invert the logic of the endstop.
2015-07-09 00:08:15 +02:00
//#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS
2015-08-20 16:07:55 +02:00
// If you want to enable the Z probe pin, but disable its use, uncomment the line below.
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z probe,
2015-07-09 00:08:15 +02:00
// this has no effect.
2015-08-10 10:35:39 +02:00
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
2015-07-09 00:08:15 +02:00
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
// :{0:'Low',1:'High'}
# define X_ENABLE_ON 0
# define Y_ENABLE_ON 0
# define Z_ENABLE_ON 0
# define E_ENABLE_ON 0 // For all extruders
2015-10-08 22:23:44 +02:00
// Disables axis stepper immediately when it's not being used.
2015-07-09 00:08:15 +02:00
// WARNING: When motors turn off there is a chance of losing position accuracy!
# define DISABLE_X false
# define DISABLE_Y false
# define DISABLE_Z false
2015-10-08 22:23:44 +02:00
// Warn on display about possibly reduced accuracy
2015-11-04 14:19:33 +01:00
//#define DISABLE_REDUCED_ACCURACY_WARNING
2015-07-09 00:08:15 +02:00
// @section extruder
# define DISABLE_E false // For all extruders
# define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
// @section machine
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
# define INVERT_X_DIR true
# define INVERT_Y_DIR false
# define INVERT_Z_DIR false
// @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
# define INVERT_E0_DIR true
# define INVERT_E1_DIR true
# define INVERT_E2_DIR false
# define INVERT_E3_DIR false
// @section homing
2016-03-08 17:50:23 +01:00
//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case.
2015-07-09 00:08:15 +02:00
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
// :[-1,1]
# define X_HOME_DIR -1
# define Y_HOME_DIR -1
# define Z_HOME_DIR -1
# define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
# define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine
// Travel limits after homing (units are in mm)
# define X_MIN_POS 0
# define Y_MIN_POS 0
# define Z_MIN_POS 0
2015-08-02 02:05:13 +02:00
# define X_MAX_POS 254 // RigidBot regular is 254mm, RigitBot Big is 406mm
# define Y_MAX_POS 248 // RigidBot regular is 248mm, RigitBot Big is 304mm
# define Z_MAX_POS 254 // RigidBot regular and Big are 254mm
2015-07-09 00:08:15 +02:00
//===========================================================================
//========================= Filament Runout Sensor ==========================
//===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
// It is assumed that when logic high = filament available
// when logic low = filament ran out
2015-07-23 03:23:23 +02:00
# if ENABLED(FILAMENT_RUNOUT_SENSOR)
2015-07-09 00:08:15 +02:00
const bool FIL_RUNOUT_INVERTING = true ; // Should be uncommented and true or false should assigned
# define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
# define FILAMENT_RUNOUT_SCRIPT "M600"
# endif
//===========================================================================
2016-02-21 05:24:22 +01:00
//============================ Mesh Bed Leveling ============================
2015-07-09 00:08:15 +02:00
//===========================================================================
2015-09-15 19:36:08 +02:00
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
2015-07-09 00:08:15 +02:00
2015-07-23 03:23:23 +02:00
# if ENABLED(MESH_BED_LEVELING)
2015-07-09 00:08:15 +02:00
# define MESH_MIN_X 10
2016-03-13 07:38:55 +01:00
# define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X))
2015-07-09 00:08:15 +02:00
# define MESH_MIN_Y 10
2016-03-13 07:38:55 +01:00
# define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y))
# define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
2015-07-09 00:08:15 +02:00
# define MESH_NUM_Y_POINTS 3
2015-08-20 16:07:55 +02:00
# define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
2016-02-21 05:24:22 +01:00
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
# if ENABLED(MANUAL_BED_LEVELING)
# define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
# endif // MANUAL_BED_LEVELING
2015-07-09 00:08:15 +02:00
# endif // MESH_BED_LEVELING
//===========================================================================
//============================ Bed Auto Leveling ============================
//===========================================================================
// @section bedlevel
2015-08-05 14:12:26 +02:00
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
2015-07-09 00:08:15 +02:00
2015-08-05 14:12:26 +02:00
# if ENABLED(AUTO_BED_LEVELING_FEATURE)
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
// There are 2 different ways to specify probing locations:
2015-07-09 00:08:15 +02:00
//
// - "grid" mode
// Probe several points in a rectangular grid.
// You specify the rectangle and the density of sample points.
// This mode is preferred because there are more measurements.
//
// - "3-point" mode
2016-03-06 05:41:15 +01:00
// Probe 3 arbitrary points on the bed (that aren't collinear)
2015-07-09 00:08:15 +02:00
// You specify the XY coordinates of all 3 points.
2015-08-20 16:07:55 +02:00
// Enable this to sample the bed in a grid (least squares solution).
// Note: this feature generates 10KB extra code size.
2015-07-09 00:08:15 +02:00
# define AUTO_BED_LEVELING_GRID
2015-07-23 03:23:23 +02:00
# if ENABLED(AUTO_BED_LEVELING_GRID)
2015-07-09 00:08:15 +02:00
# define LEFT_PROBE_BED_POSITION 15
# define RIGHT_PROBE_BED_POSITION 170
# define FRONT_PROBE_BED_POSITION 20
# define BACK_PROBE_BED_POSITION 170
2016-03-07 14:03:33 +01:00
# define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
// Set the number of grid points per dimension.
// You probably don't need more than 3 (squared=9).
2015-07-09 00:08:15 +02:00
# define AUTO_BED_LEVELING_GRID_POINTS 2
# else // !AUTO_BED_LEVELING_GRID
2015-12-10 13:18:34 +01:00
// Arbitrary points to probe.
// A simple cross-product is used to estimate the plane of the bed.
# define ABL_PROBE_PT_1_X 15
# define ABL_PROBE_PT_1_Y 180
# define ABL_PROBE_PT_2_X 15
# define ABL_PROBE_PT_2_Y 20
# define ABL_PROBE_PT_3_X 170
# define ABL_PROBE_PT_3_Y 20
2015-07-09 00:08:15 +02:00
# endif // AUTO_BED_LEVELING_GRID
2016-02-29 12:27:09 +01:00
// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
2015-08-20 16:07:55 +02:00
// X and Y offsets must be integers.
2016-02-29 12:27:09 +01:00
//
// In the following example the X and Y offsets are both positive:
// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
//
// +-- BACK ---+
// | |
// L | (+) P | R <-- probe (20,20)
// E | | I
// F | (-) N (+) | G <-- nozzle (10,10)
// T | | H
// | (-) | T
// | |
// O-- FRONT --+
// (0,0)
# define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
# define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind
# define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
# define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
# define Z_RAISE_BEFORE_PROBING 15 // How much the Z axis will be raised before traveling to the first probing point.
# define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points.
# define Z_RAISE_AFTER_PROBING 15 // How much the Z axis will be raised after the last probing point.
2015-07-09 00:08:15 +02:00
2015-12-10 13:18:34 +01:00
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
// Useful to retract a deployable Z probe.
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
2015-07-09 00:08:15 +02:00
2016-03-07 14:03:33 +01:00
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
# define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area.
2015-07-09 00:08:15 +02:00
// When defined, it will:
2015-08-20 16:07:55 +02:00
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
// - If stepper drivers timeout, it will need X and Y homing again before Z homing.
// - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
// - Block Z homing only when the Z probe is outside bed area.
2015-07-09 00:08:15 +02:00
2015-07-23 03:23:23 +02:00
# if ENABLED(Z_SAFE_HOMING)
2015-07-09 00:08:15 +02:00
2015-08-20 16:07:55 +02:00
# define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
# define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
2015-07-09 00:08:15 +02:00
# endif
2015-08-20 16:07:55 +02:00
// Support for a dedicated Z probe endstop separate from the Z min endstop.
// If you would like to use both a Z probe and a Z min endstop together,
// uncomment #define Z_MIN_PROBE_ENDSTOP and read the instructions below.
// If you still want to use the Z min endstop for homing, disable Z_SAFE_HOMING above.
// Example: To park the head outside the bed area when homing with G28.
//
// WARNING:
// The Z min endstop will need to set properly as it would without a Z probe
// to prevent head crashes and premature stopping during a print.
//
// To use a separate Z probe endstop, you must have a Z_MIN_PROBE_PIN
// defined in the pins_XXXXX.h file for your control board.
// If you are using a servo based Z probe, you will need to enable NUM_SERVOS,
// Z_ENDSTOP_SERVO_NR and SERVO_ENDSTOP_ANGLES in the R/C SERVO support below.
// RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin
// in the Aux 4 section of the RAMPS board. Use 5V for powered sensors,
// otherwise connect to ground and D32 for normally closed configuration
// and 5V and D32 for normally open configurations.
// Normally closed configuration is advised and assumed.
// The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin.
// Z_MIN_PROBE_PIN is setting the pin to use on the Arduino.
// Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
// D32 is currently selected in the RAMPS 1.3/1.4 pin file.
// All other boards will need changes to the respective pins_XXXXX.h file.
//
// WARNING:
// Setting the wrong pin may have unexpected and potentially disastrous outcomes.
// Use with caution and do your homework.
//
2015-08-10 10:35:39 +02:00
//#define Z_MIN_PROBE_ENDSTOP
2015-07-09 00:08:15 +02:00
2015-08-05 14:12:26 +02:00
# endif // AUTO_BED_LEVELING_FEATURE
2015-07-09 00:08:15 +02:00
// @section homing
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
// Manual homing switch locations:
// For deltabots this means top and center of the Cartesian print volume.
2015-07-23 03:23:23 +02:00
# if ENABLED(MANUAL_HOME_POSITIONS)
2015-07-09 00:08:15 +02:00
# define MANUAL_X_HOME_POS 0
# define MANUAL_Y_HOME_POS 0
# define MANUAL_Z_HOME_POS 0
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
# endif
// @section movement
/**
* MOVEMENT SETTINGS
*/
2015-08-02 01:35:07 +02:00
# define HOMING_FEEDRATE {50*60, 50*60, 15*60, 0} // set the homing speeds (mm/min)
2015-07-09 00:08:15 +02:00
// default settings
2015-08-02 01:35:07 +02:00
# define DEFAULT_AXIS_STEPS_PER_UNIT {44.3090, 22.1545, 1600, 53.5} // default steps per unit for RigidBot with standard hardware
// default steps for 16-teth polleys {100.06,50.06,1600,76}, HPX2-MAX E=504, RigidBot E=53.5, Peter Stoneham's=76
# define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
# define DEFAULT_MAX_ACCELERATION {800, 800, 100, 10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
2015-07-09 00:08:15 +02:00
# define DEFAULT_ACCELERATION 600 // X, Y, Z and E acceleration in mm/s^2 for printing moves
# define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts
2015-08-02 01:35:07 +02:00
# define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
2015-07-09 00:08:15 +02:00
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
# define DEFAULT_XYJERK 8.0 // (mm/sec)
# define DEFAULT_ZJERK 0.4 // (mm/sec)
# define DEFAULT_EJERK 5.0 // (mm/sec)
//=============================================================================
//============================= Additional Features ===========================
//=============================================================================
// @section more
// Custom M code points
# define CUSTOM_M_CODES
2015-07-23 03:23:23 +02:00
# if ENABLED(CUSTOM_M_CODES)
2015-08-05 14:12:26 +02:00
# if ENABLED(AUTO_BED_LEVELING_FEATURE)
2015-07-09 00:08:15 +02:00
# define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
# define Z_PROBE_OFFSET_RANGE_MIN -20
# define Z_PROBE_OFFSET_RANGE_MAX 20
# endif
# endif
// @section extras
// EEPROM
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable EEPROM support
2015-12-13 02:57:36 +01:00
# define EEPROM_SETTINGS
2015-07-09 00:08:15 +02:00
2015-07-23 03:23:23 +02:00
# if ENABLED(EEPROM_SETTINGS)
2015-07-09 00:08:15 +02:00
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
# define EEPROM_CHITCHAT // Please keep turned on if you can.
# endif
2015-08-02 01:35:07 +02:00
//
// M100 Free Memory Watcher
//
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
2015-07-09 00:08:15 +02:00
// @section temperature
// Preheat Constants
# define PLA_PREHEAT_HOTEND_TEMP 180
# define PLA_PREHEAT_HPB_TEMP 70
# define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
# define ABS_PREHEAT_HOTEND_TEMP 240
# define ABS_PREHEAT_HPB_TEMP 110
# define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
//==============================LCD and SD support=============================
// @section lcd
// Define your display language below. Replace (en) with your language code and uncomment.
// en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
// See also language.h
# define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
// See also documentation/LCDLanguageFont.md
2015-08-02 01:35:07 +02:00
# define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware
//#define DISPLAY_CHARSET_HD44780_WESTERN
2015-07-09 00:08:15 +02:00
//#define DISPLAY_CHARSET_HD44780_CYRILLIC
//#define ULTRA_LCD //general LCD support, also 16x2
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
2015-12-13 02:57:36 +01:00
# define SDSUPPORT // Enable SD Card Support in Hardware Console
2016-02-07 06:17:17 +01:00
// Changed behaviour! If you need SDSUPPORT uncomment it!
2015-12-14 05:23:01 +01:00
# define SPI_SPEED SPI_EIGHTH_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
2015-07-09 00:08:15 +02:00
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
//#define ULTIPANEL //the UltiPanel as on Thingiverse
2015-07-24 23:19:09 +02:00
//#define SPEAKER // The sound device is a speaker - not a buzzer. A buzzer resonates with his own frequency.
2015-07-09 00:08:15 +02:00
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
// http://reprap.org/wiki/PanelOne
//#define PANEL_ONE
// The MaKr3d Makr-Panel with graphic controller and SD support
// http://reprap.org/wiki/MaKr3d_MaKrPanel
//#define MAKRPANEL
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
// http://panucatt.com
2015-12-10 12:59:36 +01:00
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
2015-07-09 00:08:15 +02:00
//#define VIKI2
//#define miniVIKI
// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
//
2015-12-10 12:59:36 +01:00
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
2015-07-09 00:08:15 +02:00
//#define ELB_FULL_GRAPHIC_CONTROLLER
2015-08-01 01:40:50 +02:00
//#define SD_DETECT_INVERTED
2015-07-09 00:08:15 +02:00
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
// The GADGETS3D G3D LCD/SD Controller (blue PCB)
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
//#define G3D_PANEL
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
//
2015-12-10 12:59:36 +01:00
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
2015-07-09 01:44:20 +02:00
//
// RigidBoard: To rewire this for a RigidBot see http://rigidtalk.com/wiki/index.php?title=LCD_Smart_Controller
//
2015-07-09 00:08:15 +02:00
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
//#define REPRAPWORLD_KEYPAD
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
// The Elefu RA Board Control Panel
// http://www.elefu.com/index.php?route=product/product&product_id=53
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
//#define RA_CONTROL_PANEL
2016-03-07 14:03:33 +01:00
// The MakerLab Mini Panel with graphic controller and SD support
// http://reprap.org/wiki/Mini_panel
//#define MINIPANEL
2015-07-09 01:44:20 +02:00
// RigidBot Panel V1.0
// http://www.inventapart.com/
# define RIGIDBOT_PANEL
2015-07-09 00:08:15 +02:00
/**
* I2C Panels
*/
//#define LCD_I2C_SAINSMART_YWROBOT
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
2015-07-16 01:09:30 +02:00
//
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
2015-07-09 00:08:15 +02:00
//#define LCD_I2C_PANELOLU2
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
//#define LCD_I2C_VIKI
2015-10-13 12:47:49 +02:00
2015-07-09 00:08:15 +02:00
// SSD1306 OLED generic display support
2015-12-10 12:59:36 +01:00
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
2015-07-09 00:08:15 +02:00
//#define U8GLIB_SSD1306
// Shift register panels
// ---------------------
// 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
//#define SAV_3DLCD
// @section extras
2016-03-06 05:41:15 +01:00
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
2015-07-09 00:08:15 +02:00
//#define FAST_PWM_FAN
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
// is too low, you should also increment SOFT_PWM_SCALE.
//#define FAN_SOFT_PWM
// Incrementing this by 1 will double the software PWM frequency,
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
// However, control resolution will be halved for each increment;
// at zero value, there are 128 effective control positions.
# define SOFT_PWM_SCALE 0
// Temperature status LEDs that display the hotend and bet temperature.
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
// Otherwise the RED led is on. There is 1C hysteresis.
//#define TEMP_STAT_LEDS
// M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
2015-09-15 19:36:08 +02:00
//#define PHOTOGRAPH_PIN 23
2015-07-09 00:08:15 +02:00
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX
// Support for the BariCUDA Paste Extruder.
//#define BARICUDA
//define BlinkM/CyzRgb Support
//#define BLINKM
/*********************************************************************\
* R / C SERVO support
* Sponsored by TrinityLabs , Reworked by codexmas
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
// Number of servos
//
// If you select a configuration below, this will receive a default value and does not need to be set manually
// set it manually if you have more servos than extruders and wish to manually control some
// leaving it undefined or defining as 0 will disable the servo subsystem
// If unsure, leave commented / disabled
//
# define NUM_SERVOS 0 // DGlass3D - Servo index starts with 0 for M280 command
// Servo Endstops
//
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
2015-08-20 16:07:55 +02:00
// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500.
2015-07-09 00:08:15 +02:00
//
2015-07-24 11:26:05 +02:00
//#define X_ENDSTOP_SERVO_NR 1
//#define Y_ENDSTOP_SERVO_NR 2
//#define Z_ENDSTOP_SERVO_NR 0
2015-07-29 04:22:44 +02:00
//#define SERVO_ENDSTOP_ANGLES {{0,0}, {0,0}, {70,0}} // X,Y,Z Axis Extend and Retract angles
2015-07-09 00:08:15 +02:00
2015-07-16 01:08:26 +02:00
// Servo deactivation
//
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
2015-07-23 03:23:23 +02:00
# if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
2015-07-16 01:08:26 +02:00
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
# define SERVO_DEACTIVATION_DELAY 300
# endif
2015-07-09 00:08:15 +02:00
/**********************************************************************\
* Support for a filament diameter sensor
* Also allows adjustment of diameter at print time ( vs at slicing )
* Single extruder only at this point ( extruder 0 )
*
* Motherboards
* 34 - RAMPS1 .4 - uses Analog input 5 on the AUX2 connector
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector ( version B , C , D , E )
* 301 - Rambo - uses Analog input 3
* Note may require analog pins to be defined for different motherboards
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
// Uncomment below to enable
//#define FILAMENT_SENSOR
# define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
# define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
# define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
# define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
# define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
2016-03-06 05:41:15 +01:00
# define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm) - limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
2015-07-09 00:08:15 +02:00
//defines used in the code
# define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
//#define FILAMENT_LCD_DISPLAY
# include "Configuration_adv.h"
# include "thermistortables.h"
2015-07-16 01:09:30 +02:00
# endif //CONFIGURATION_H