Extended comment explaining M42 usage

This commit is contained in:
Bas Spaans 2013-01-31 18:00:25 +01:00
parent 12c41423ad
commit 01541ee64c

View File

@ -88,7 +88,7 @@
// M29 - Stop SD write // M29 - Stop SD write
// M30 - Delete file from SD (M30 filename.g) // M30 - Delete file from SD (M30 filename.g)
// M31 - Output time since last M109 or SD card start to serial // M31 - Output time since last M109 or SD card start to serial
// M42 - Change pin status via gcode // M42 - Change pin status via gcode. Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
// M80 - Turn on Power Supply // M80 - Turn on Power Supply
// M81 - Turn off Power Supply // M81 - Turn off Power Supply
// M82 - Set E codes absolute (default) // M82 - Set E codes absolute (default)
@ -124,7 +124,8 @@
// M500 - stores paramters in EEPROM // M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
// M503 - print the current settings (from memory not from eeprom) // M503 - print the current settings (from memory not from eeprom)
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) // M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] // M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
// M907 - Set digital trimpot motor current using axis codes. // M907 - Set digital trimpot motor current using axis codes.
@ -958,7 +959,7 @@ void process_commands()
autotempShutdown(); autotempShutdown();
} }
break; break;
case 42: //M42 -Change pin status via gcode case 42: //M42 -Change pin status via gcode
if (code_seen('S')) if (code_seen('S'))
{ {
int pin_status = code_value(); int pin_status = code_value();
@ -1499,13 +1500,20 @@ void process_commands()
{ {
Config_PrintSettings(); Config_PrintSettings();
} }
break; break;
#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
case 540: #ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
{
if(code_seen('S')) abort_on_endstop_hit = code_value() > 0; case 540:
}
break; {
if(code_seen('S')) abort_on_endstop_hit = code_value() > 0;
}
break;
#endif #endif
#ifdef FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE
case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]