Try on "CLEARANCE" for size
This commit is contained in:
parent
0e7d638a7a
commit
01f1028510
@ -602,10 +602,10 @@
|
||||
#define XY_PROBE_SPEED 4000
|
||||
#endif
|
||||
#endif
|
||||
#if Z_RAISE_BETWEEN_PROBES > Z_RAISE_DEPLOY_PROBE
|
||||
#define _Z_RAISE_DEPLOY_PROBE Z_RAISE_BETWEEN_PROBES
|
||||
#if Z_CLEARANCE_BETWEEN_PROBES > Z_CLEARANCE_DEPLOY_PROBE
|
||||
#define _Z_CLEARANCE_DEPLOY_PROBE Z_CLEARANCE_BETWEEN_PROBES
|
||||
#else
|
||||
#define _Z_RAISE_DEPLOY_PROBE Z_RAISE_DEPLOY_PROBE
|
||||
#define _Z_CLEARANCE_DEPLOY_PROBE Z_CLEARANCE_DEPLOY_PROBE
|
||||
#endif
|
||||
#else
|
||||
#undef X_PROBE_OFFSET_FROM_EXTRUDER
|
||||
@ -681,17 +681,17 @@
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Z_HOMING_HEIGHT / Z_RAISE_BETWEEN_PROBES
|
||||
* Z_HOMING_HEIGHT / Z_CLEARANCE_BETWEEN_PROBES
|
||||
*/
|
||||
#ifndef Z_HOMING_HEIGHT
|
||||
#ifndef Z_RAISE_BETWEEN_PROBES
|
||||
#ifndef Z_CLEARANCE_BETWEEN_PROBES
|
||||
#define Z_HOMING_HEIGHT 0
|
||||
#else
|
||||
#define Z_HOMING_HEIGHT Z_RAISE_BETWEEN_PROBES
|
||||
#define Z_HOMING_HEIGHT Z_CLEARANCE_BETWEEN_PROBES
|
||||
#endif
|
||||
#endif
|
||||
#ifndef Z_RAISE_BETWEEN_PROBES
|
||||
#define Z_RAISE_BETWEEN_PROBES Z_HOMING_HEIGHT
|
||||
#ifndef Z_CLEARANCE_BETWEEN_PROBES
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES Z_HOMING_HEIGHT
|
||||
#endif
|
||||
|
||||
#if IS_KINEMATIC
|
||||
|
@ -630,11 +630,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 10 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -1882,7 +1882,7 @@ static void clean_up_after_endstop_or_probe_move() {
|
||||
if (endstops.z_probe_enabled == deploy) return false;
|
||||
|
||||
// Make room for probe
|
||||
do_probe_raise(_Z_RAISE_DEPLOY_PROBE);
|
||||
do_probe_raise(_Z_CLEARANCE_DEPLOY_PROBE);
|
||||
|
||||
// Check BLTOUCH probe status for an error
|
||||
#if ENABLED(BLTOUCH)
|
||||
@ -1991,7 +1991,7 @@ static void clean_up_after_endstop_or_probe_move() {
|
||||
|
||||
// If the nozzle is above the travel height then
|
||||
// move down quickly before doing the slow probe
|
||||
float z = LOGICAL_Z_POSITION(Z_RAISE_BETWEEN_PROBES);
|
||||
float z = LOGICAL_Z_POSITION(Z_CLEARANCE_BETWEEN_PROBES);
|
||||
if (z < current_position[Z_AXIS])
|
||||
do_blocking_move_to_z(z, MMM_TO_MMS(Z_PROBE_SPEED_FAST));
|
||||
|
||||
@ -2030,7 +2030,7 @@ static void clean_up_after_endstop_or_probe_move() {
|
||||
float old_feedrate_mm_s = feedrate_mm_s;
|
||||
|
||||
// Ensure a minimum height before moving the probe
|
||||
do_probe_raise(Z_RAISE_BETWEEN_PROBES);
|
||||
do_probe_raise(Z_CLEARANCE_BETWEEN_PROBES);
|
||||
|
||||
// Move to the XY where we shall probe
|
||||
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||
@ -2051,7 +2051,7 @@ static void clean_up_after_endstop_or_probe_move() {
|
||||
float measured_z = run_z_probe();
|
||||
|
||||
if (!stow)
|
||||
do_probe_raise(Z_RAISE_BETWEEN_PROBES);
|
||||
do_probe_raise(Z_CLEARANCE_BETWEEN_PROBES);
|
||||
else
|
||||
if (STOW_PROBE()) return NAN;
|
||||
|
||||
@ -3097,8 +3097,8 @@ inline void gcode_G28() {
|
||||
feedrate_mm_s = homing_feedrate_mm_s[X_AXIS];
|
||||
|
||||
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
|
||||
#if Z_RAISE_BETWEEN_PROBES > Z_HOMING_HEIGHT
|
||||
+ Z_RAISE_BETWEEN_PROBES
|
||||
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
|
||||
+ Z_CLEARANCE_BETWEEN_PROBES
|
||||
#elif Z_HOMING_HEIGHT > 0
|
||||
+ Z_HOMING_HEIGHT
|
||||
#endif
|
||||
@ -3109,7 +3109,7 @@ inline void gcode_G28() {
|
||||
current_position[Y_AXIS] = LOGICAL_Y_POSITION(y);
|
||||
line_to_current_position();
|
||||
|
||||
#if Z_RAISE_BETWEEN_PROBES > 0 || Z_HOMING_HEIGHT > 0
|
||||
#if Z_CLEARANCE_BETWEEN_PROBES > 0 || Z_HOMING_HEIGHT > 0
|
||||
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z);
|
||||
line_to_current_position();
|
||||
#endif
|
||||
@ -3204,8 +3204,8 @@ inline void gcode_G28() {
|
||||
else {
|
||||
// One last "return to the bed" (as originally coded) at completion
|
||||
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
|
||||
#if Z_RAISE_BETWEEN_PROBES > Z_HOMING_HEIGHT
|
||||
+ Z_RAISE_BETWEEN_PROBES
|
||||
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
|
||||
+ Z_CLEARANCE_BETWEEN_PROBES
|
||||
#elif Z_HOMING_HEIGHT > 0
|
||||
+ Z_HOMING_HEIGHT
|
||||
#endif
|
||||
@ -3558,7 +3558,7 @@ inline void gcode_G28() {
|
||||
|
||||
#endif // AUTO_BED_LEVELING_3POINT
|
||||
|
||||
// Raise to _Z_RAISE_DEPLOY_PROBE. Stow the probe.
|
||||
// Raise to _Z_CLEARANCE_DEPLOY_PROBE. Stow the probe.
|
||||
if (STOW_PROBE()) return;
|
||||
|
||||
// Restore state after probing
|
||||
|
@ -130,11 +130,11 @@
|
||||
#elif defined(MIN_Z_HEIGHT_FOR_HOMING)
|
||||
#error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
|
||||
#elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
|
||||
#error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_RAISE_DEPLOY_PROBE instead."
|
||||
#error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE instead."
|
||||
#elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
|
||||
#error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_RAISE_DEPLOY_PROBE and Z_RAISE_BETWEEN_PROBES. Please update your configuration."
|
||||
#error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
|
||||
#elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
|
||||
#error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_RAISE_DEPLOY_PROBE and Z_RAISE_BETWEEN_PROBES. Please update your configuration."
|
||||
#error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
|
||||
#elif !defined(MIN_STEPS_PER_SEGMENT)
|
||||
#error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
|
||||
#elif defined(PREVENT_DANGEROUS_EXTRUDE)
|
||||
@ -427,14 +427,14 @@
|
||||
/**
|
||||
* Make sure Z raise values are set
|
||||
*/
|
||||
#if !defined(Z_RAISE_DEPLOY_PROBE)
|
||||
#error "You must define Z_RAISE_DEPLOY_PROBE in your configuration."
|
||||
#elif !defined(Z_RAISE_BETWEEN_PROBES)
|
||||
#error "You must define Z_RAISE_BETWEEN_PROBES in your configuration."
|
||||
#elif Z_RAISE_DEPLOY_PROBE < 0
|
||||
#error "Probes need Z_RAISE_DEPLOY_PROBE >= 0."
|
||||
#elif Z_RAISE_BETWEEN_PROBES < 0
|
||||
#error "Probes need Z_RAISE_BETWEEN_PROBES >= 0."
|
||||
#if !defined(Z_CLEARANCE_DEPLOY_PROBE)
|
||||
#error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration."
|
||||
#elif !defined(Z_CLEARANCE_BETWEEN_PROBES)
|
||||
#error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration."
|
||||
#elif Z_CLEARANCE_DEPLOY_PROBE < 0
|
||||
#error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0."
|
||||
#elif Z_CLEARANCE_BETWEEN_PROBES < 0
|
||||
#error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
@ -613,11 +613,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -596,11 +596,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -594,11 +594,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -605,11 +605,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -607,11 +607,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 5 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 2 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -630,11 +630,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -613,11 +613,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -613,11 +613,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -613,11 +613,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -611,11 +611,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -623,11 +623,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -634,11 +634,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -605,11 +605,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -613,11 +613,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -703,11 +703,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 50 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 50 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -697,11 +697,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -700,11 +700,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 50 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 50 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -701,11 +701,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 100 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 100 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -703,11 +703,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 20 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 10 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 20 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -616,11 +616,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
@ -609,11 +609,11 @@
|
||||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||||
* Only integer values >= 1 are valid here.
|
||||
*
|
||||
* Example: `M851 Z-5` with a RAISE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a RAISE of 2 => 2mm from bed to nozzle.
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_RAISE_DEPLOY_PROBE 15 // Z Raise for Deploy/Stow
|
||||
#define Z_RAISE_BETWEEN_PROBES 5 // Z Raise between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
|
Loading…
Reference in New Issue
Block a user