🔧 Cutter pins for SKR 2.0

This commit is contained in:
Scott Lahteine 2021-12-04 17:17:10 -06:00 committed by Scott Lahteine
parent aa3ec2fbfd
commit 05b57278d4

View File

@ -181,16 +181,28 @@
#define Z_CS_PIN PD0
#endif
#define E0_STEP_PIN PD15
#define E0_DIR_PIN PD14
#define E0_ENABLE_PIN PC7
#ifndef E0_STEP_PIN
#define E0_STEP_PIN PD15
#endif
#ifndef E0_DIR_PIN
#define E0_DIR_PIN PD14
#endif
#ifndef E0_ENABLE_PIN
#define E0_ENABLE_PIN PC7
#endif
#ifndef E0_CS_PIN
#define E0_CS_PIN PC6
#endif
#define E1_STEP_PIN PD11
#define E1_DIR_PIN PD10
#define E1_ENABLE_PIN PD13
#ifndef E1_STEP_PIN
#define E1_STEP_PIN PD11
#endif
#ifndef E1_DIR_PIN
#define E1_DIR_PIN PD10
#endif
#ifndef E1_ENABLE_PIN
#define E1_ENABLE_PIN PD13
#endif
#ifndef E1_CS_PIN
#define E1_CS_PIN PD12
#endif
@ -198,9 +210,15 @@
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA1 // TB
#define TEMP_0_PIN PA2 // TH0
#define TEMP_1_PIN PA3 // TH1
#ifndef TEMP_0_PIN
#define TEMP_0_PIN PA2 // TH0
#endif
#ifndef TEMP_1_PIN
#define TEMP_1_PIN PA3 // TH1
#endif
#ifndef TEMP_BED_PIN
#define TEMP_BED_PIN PA1 // TB
#endif
#if HOTENDS == 1 && DISABLED(HEATERS_PARALLEL)
#if TEMP_SENSOR_PROBE
@ -225,12 +243,22 @@
#ifndef FAN_PIN
#define FAN_PIN PB7 // Fan0
#endif
#ifndef FAN1_PIN
#define FAN1_PIN PB6 // Fan1
#endif
#ifndef FAN2_PIN
#define FAN2_PIN PB5 // Fan2
#endif
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
#ifndef SPINDLE_LASER_PWM_PIN
#define SPINDLE_LASER_PWM_PIN PB5
#endif
#ifndef SPINDLE_LASER_ENA_PIN
#define SPINDLE_LASER_ENA_PIN PB6
#endif
#else
#ifndef FAN1_PIN
#define FAN1_PIN PB6 // Fan1
#endif
#ifndef FAN2_PIN
#define FAN2_PIN PB5 // Fan2
#endif
#endif // SPINDLE_FEATURE || LASER_FEATURE
//
// Software SPI pins for TMC2130 stepper drivers
@ -266,6 +294,9 @@
//#define E3_HARDWARE_SERIAL Serial1
//#define E4_HARDWARE_SERIAL Serial1
//
// Software serial
//
#define X_SERIAL_TX_PIN PE0
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
@ -324,7 +355,16 @@
// Onboard SD card
// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
//
#if SD_CONNECTION_IS(ONBOARD)
#if SD_CONNECTION_IS(LCD)
#define SDSS PA4
#define SD_SS_PIN SDSS
#define SD_SCK_PIN PA5
#define SD_MISO_PIN PA6
#define SD_MOSI_PIN PA7
#define SD_DETECT_PIN PC4
#elif SD_CONNECTION_IS(ONBOARD)
#define SDIO_SUPPORT // Use SDIO for onboard SD
#define SDIO_D0_PIN PC8
@ -334,17 +374,8 @@
#define SDIO_CK_PIN PC12
#define SDIO_CMD_PIN PD2
#elif SD_CONNECTION_IS(LCD)
#define SDSS PA4
#define SD_SS_PIN SDSS
#define SD_SCK_PIN PA5
#define SD_MISO_PIN PA6
#define SD_MOSI_PIN PA7
#define SD_DETECT_PIN PC4
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
#error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board"
#error "No custom SD drive cable defined for this board."
#endif
#if ENABLED(BTT_MOTOR_EXPANSION)