added individual pullup setting option to have finer control in case there is a special z-min sensor, for example
This commit is contained in:
parent
e792d62f47
commit
0e5e249ab5
@ -127,9 +127,28 @@
|
|||||||
//=============================Mechanical Settings===========================
|
//=============================Mechanical Settings===========================
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
|
|
||||||
// Endstop Settings
|
// corse Endstop Settings
|
||||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||||
|
|
||||||
|
#ifndef ENDSTOPPULLUPS
|
||||||
|
// fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined
|
||||||
|
#define ENDSTOPPULLUP_XMAX
|
||||||
|
#define ENDSTOPPULLUP_YMAX
|
||||||
|
#define ENDSTOPPULLUP_ZMAX
|
||||||
|
#define ENDSTOPPULLUP_XMIN
|
||||||
|
#define ENDSTOPPULLUP_YMIN
|
||||||
|
//#define ENDSTOPPULLUP_ZMIN
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifdef ENDSTOPPULLUPS
|
||||||
|
#define ENDSTOPPULLUP_XMAX
|
||||||
|
#define ENDSTOPPULLUP_YMAX
|
||||||
|
#define ENDSTOPPULLUP_ZMAX
|
||||||
|
#define ENDSTOPPULLUP_XMIN
|
||||||
|
#define ENDSTOPPULLUP_YMIN
|
||||||
|
#define ENDSTOPPULLUP_ZMIN
|
||||||
|
#endif
|
||||||
|
|
||||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||||
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
||||||
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
||||||
|
@ -659,51 +659,48 @@ void st_init()
|
|||||||
#endif
|
#endif
|
||||||
|
|
||||||
//endstops and pullups
|
//endstops and pullups
|
||||||
#ifdef ENDSTOPPULLUPS
|
|
||||||
#if X_MIN_PIN > -1
|
#if X_MIN_PIN > -1
|
||||||
SET_INPUT(X_MIN_PIN);
|
SET_INPUT(X_MIN_PIN);
|
||||||
|
#ifdef ENDSTOPPULLUP_XMIN
|
||||||
WRITE(X_MIN_PIN,HIGH);
|
WRITE(X_MIN_PIN,HIGH);
|
||||||
#endif
|
#endif
|
||||||
#if X_MAX_PIN > -1
|
#endif
|
||||||
SET_INPUT(X_MAX_PIN);
|
|
||||||
WRITE(X_MAX_PIN,HIGH);
|
#if Y_MIN_PIN > -1
|
||||||
#endif
|
SET_INPUT(Y_MIN_PIN);
|
||||||
#if Y_MIN_PIN > -1
|
#ifdef ENDSTOPPULLUP_YMIN
|
||||||
SET_INPUT(Y_MIN_PIN);
|
|
||||||
WRITE(Y_MIN_PIN,HIGH);
|
WRITE(Y_MIN_PIN,HIGH);
|
||||||
#endif
|
#endif
|
||||||
#if Y_MAX_PIN > -1
|
#endif
|
||||||
SET_INPUT(Y_MAX_PIN);
|
|
||||||
WRITE(Y_MAX_PIN,HIGH);
|
#if Z_MIN_PIN > -1
|
||||||
#endif
|
SET_INPUT(Z_MIN_PIN);
|
||||||
#if Z_MIN_PIN > -1
|
#ifdef ENDSTOPPULLUP_ZMIN
|
||||||
SET_INPUT(Z_MIN_PIN);
|
|
||||||
WRITE(Z_MIN_PIN,HIGH);
|
WRITE(Z_MIN_PIN,HIGH);
|
||||||
#endif
|
#endif
|
||||||
#if Z_MAX_PIN > -1
|
#endif
|
||||||
SET_INPUT(Z_MAX_PIN);
|
|
||||||
|
#if X_MAX_PIN > -1
|
||||||
|
SET_INPUT(X_MAX_PIN);
|
||||||
|
#ifdef ENDSTOPPULLUP_XMAX
|
||||||
|
WRITE(X_MAX_PIN,HIGH);
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if Y_MAX_PIN > -1
|
||||||
|
SET_INPUT(Y_MAX_PIN);
|
||||||
|
#ifdef ENDSTOPPULLUP_YMAX
|
||||||
|
WRITE(Y_MAX_PIN,HIGH);
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if Z_MAX_PIN > -1
|
||||||
|
SET_INPUT(Z_MAX_PIN);
|
||||||
|
#ifdef ENDSTOPPULLUP_ZMAX
|
||||||
WRITE(Z_MAX_PIN,HIGH);
|
WRITE(Z_MAX_PIN,HIGH);
|
||||||
#endif
|
#endif
|
||||||
#else //ENDSTOPPULLUPS
|
#endif
|
||||||
#if X_MIN_PIN > -1
|
|
||||||
SET_INPUT(X_MIN_PIN);
|
|
||||||
#endif
|
|
||||||
#if X_MAX_PIN > -1
|
|
||||||
SET_INPUT(X_MAX_PIN);
|
|
||||||
#endif
|
|
||||||
#if Y_MIN_PIN > -1
|
|
||||||
SET_INPUT(Y_MIN_PIN);
|
|
||||||
#endif
|
|
||||||
#if Y_MAX_PIN > -1
|
|
||||||
SET_INPUT(Y_MAX_PIN);
|
|
||||||
#endif
|
|
||||||
#if Z_MIN_PIN > -1
|
|
||||||
SET_INPUT(Z_MIN_PIN);
|
|
||||||
#endif
|
|
||||||
#if Z_MAX_PIN > -1
|
|
||||||
SET_INPUT(Z_MAX_PIN);
|
|
||||||
#endif
|
|
||||||
#endif //ENDSTOPPULLUPS
|
|
||||||
|
|
||||||
|
|
||||||
//Initialize Step Pins
|
//Initialize Step Pins
|
||||||
|
Loading…
Reference in New Issue
Block a user