merged with triffid fork
This commit is contained in:
Erik van der Zalm
commit
11518a987f
356
Marlin/Makefile
356
Marlin/Makefile
@ -1,76 +1,70 @@
|
||||
# Sprinter Arduino Project Makefile
|
||||
#
|
||||
# Makefile Based on:
|
||||
# Arduino 0011 Makefile
|
||||
# Arduino adaptation by mellis, eighthave, oli.keller
|
||||
#
|
||||
# This has been tested with Arduino 0022.
|
||||
#
|
||||
# This makefile allows you to build sketches from the command line
|
||||
# without the Arduino environment (or Java).
|
||||
#
|
||||
# Detailed instructions for using the makefile:
|
||||
#
|
||||
# 1. Modify the line containg "INSTALL_DIR" to point to the directory that
|
||||
# contains the Arduino installation (for example, under Mac OS X, this
|
||||
# might be /Applications/arduino-0012).
|
||||
#
|
||||
# 2. Modify the line containing "PORT" to refer to the filename
|
||||
# representing the USB or serial connection to your Arduino board
|
||||
# (e.g. PORT = /dev/tty.USB0). If the exact name of this file
|
||||
# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*).
|
||||
#
|
||||
# 3. Set the line containing "MCU" to match your board's processor.
|
||||
# Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
|
||||
# or Diecimila have the atmega168. If you're using a LilyPad Arduino,
|
||||
# change F_CPU to 8000000.
|
||||
#
|
||||
# 4. Type "make" and press enter to compile/verify your program.
|
||||
#
|
||||
# 5. Type "make upload", reset your Arduino board, and press enter to
|
||||
# upload your program to the Arduino board.
|
||||
#
|
||||
# $Id$
|
||||
|
||||
#For "old" Arduino Mega
|
||||
MCU = atmega1280
|
||||
#For Arduino Mega2560
|
||||
#MCU = atmega2560
|
||||
#For Sanguinololu
|
||||
#MCU = atmega644p
|
||||
|
||||
#Arduino install directory
|
||||
INSTALL_DIR = ../../arduino-0022/
|
||||
|
||||
F_CPU = 16000000
|
||||
|
||||
UPLOAD_RATE = 115200
|
||||
AVRDUDE_PROGRAMMER = arduino
|
||||
PORT = /dev/arduino
|
||||
|
||||
TARGET = $(notdir $(CURDIR))
|
||||
# CHANGE BELOW:
|
||||
#~ INSTALL_DIR = /Applications/Arduino.app/Contents/Resources/Java
|
||||
INSTALL_DIR = /home/bkubicek/software/arduino-0023
|
||||
#~ PORT = /dev/cu.usbserial*
|
||||
PORT = /dev/ttyACM0
|
||||
|
||||
# Get these values from:
|
||||
# $(INSTALL_DIR)/hardware/boards.txt
|
||||
# (arduino-0022/hardware/arduino/boards.txt)
|
||||
# The values below are for the "Arduino Duemilanove or Nano w/ ATmega328"
|
||||
# now for "Arduino Mega 2560"
|
||||
UPLOAD_SPEED = 115200
|
||||
UPLOAD_PROTOCOL = stk500v2
|
||||
BUILD_MCU = atmega2560
|
||||
BUILD_F_CPU = 16000000L
|
||||
TERM=bash
|
||||
|
||||
# getting undefined reference to `__cxa_pure_virtual'
|
||||
#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
|
||||
#~ http://www.arduino.cc/playground/OpenBSD/CLI
|
||||
#~ [http://arduino.cc/forum/index.php?topic=52041.0 A "simple" makefile for Arduino]
|
||||
#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1275488191 Arduino Forum - Configuring avr-gcc options in arduino IDE]
|
||||
# found in /usr/lib/gcc/avr/4.3.5/cc1plus; fixed with -Wl,--gc-section
|
||||
|
||||
############################################################################
|
||||
# Below here nothing should be changed...
|
||||
|
||||
LINKORDER=\
|
||||
applet/Marlin.cpp.o \
|
||||
applet/EEPROM.o \
|
||||
applet/main.o \
|
||||
applet/MarlinSerial.o \
|
||||
applet/motion_control.o\
|
||||
applet/pins_arduino.o\
|
||||
applet/planner.o\
|
||||
applet/Print.o\
|
||||
applet/Sd2Card.o\
|
||||
applet/SdBaseFile.o\
|
||||
applet/SdFatUtil.o\
|
||||
applet/SdFile.o\
|
||||
applet/SdVolume.o\
|
||||
applet/stepper.o\
|
||||
applet/temperature.o\
|
||||
applet/WInterrupts.o\
|
||||
applet/wiring_analog.o\
|
||||
applet/wiring_digital.o\
|
||||
applet/wiring.o\
|
||||
applet/wiring_pulse.o\
|
||||
applet/wiring_shift.o\
|
||||
applet/WMath.o
|
||||
|
||||
PDES=Marlin.pde ultralcd.pde watchdog.pde cardreader.pde
|
||||
ARDUINO = $(INSTALL_DIR)/hardware/arduino/cores/arduino
|
||||
#
|
||||
#~ AVR_TOOLS_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
|
||||
# in Ubuntu, avr-gcc is installed separate;
|
||||
# only avrdude comes with the IDE
|
||||
AVR_TOOLS_PATH = /usr/bin
|
||||
AVR_DUDE_PATH = $(INSTALL_DIR)/hardware/tools
|
||||
#
|
||||
AVR_TOOLS_PATH =
|
||||
SRC = $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \
|
||||
$(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
|
||||
$(ARDUINO)/wiring_pulse.c \
|
||||
$(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
|
||||
# added applet/$(TARGET).cpp as in IDE 0022
|
||||
CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \
|
||||
$(ARDUINO)/Print.cpp \
|
||||
$(ARDUINO)/main.cpp
|
||||
# applet/$(TARGET).cpp # no need, having a rule now for applet/$(TARGET).cpp.o
|
||||
# added main.cpp, as in 0022
|
||||
CXXSRC = $(ARDUINO)/WMath.cpp $(ARDUINO)/WString.cpp\
|
||||
$(ARDUINO)/Print.cpp Marlin.cpp MarlinSerial.cpp Sd2Card.cpp SdBaseFile.cpp SdFatUtil.cpp SdFile.cpp SdVolume.cpp motion_control.cpp planner.cpp stepper.cpp temperature.cpp cardreader.cpp
|
||||
FORMAT = ihex
|
||||
|
||||
|
||||
# Name of this Makefile (used for "make depend").
|
||||
MAKEFILE = Makefile
|
||||
|
||||
@ -79,17 +73,14 @@ MAKEFILE = Makefile
|
||||
# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
|
||||
DEBUG = stabs
|
||||
|
||||
OPT = 2
|
||||
OPT = s
|
||||
|
||||
# Place -D or -U options here
|
||||
#~ CDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
|
||||
#~ CXXDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
|
||||
# now called DF_CPU
|
||||
CDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=23
|
||||
CXXDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=23
|
||||
CDEFS = -DF_CPU=$(F_CPU)
|
||||
CXXDEFS = -DF_CPU=$(F_CPU)
|
||||
|
||||
# Place -I options here
|
||||
CINCS = -I$(ARDUINO) -I$(INSTALL_DIR)/libraries/LiquidCrystal/ -I$(INSTALL_DIR)/libraries/EEPROM/
|
||||
CINCS = -I$(ARDUINO)
|
||||
CXXINCS = -I$(ARDUINO)
|
||||
|
||||
# Compiler flag to set the C Standard level.
|
||||
@ -97,114 +88,56 @@ CXXINCS = -I$(ARDUINO)
|
||||
# gnu89 - c89 plus GCC extensions
|
||||
# c99 - ISO C99 standard (not yet fully implemented)
|
||||
# gnu99 - c99 plus GCC extensions
|
||||
CSTANDARD = -std=gnu99
|
||||
#CSTANDARD = -std=gnu99
|
||||
CDEBUG = -g$(DEBUG)
|
||||
# note that typically, IDE 0022 uses -w to suppress warnings (both in cpp and c)!
|
||||
CWARN = -Wall
|
||||
#~ CWARN = -w
|
||||
# "-Wstrict-prototypes" is valid for Ada/C/ObjC but not for C++:
|
||||
CCWARN = -Wstrict-prototypes
|
||||
CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
|
||||
CWARN = -Wall -Wstrict-prototypes
|
||||
CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -w -ffunction-sections -fdata-sections -DARDUINO=22
|
||||
#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
|
||||
|
||||
# to eliminate pins_ardiuno warnings:
|
||||
# http://arduino.cc/pipermail/developers_arduino.cc/2010-December/004005.html
|
||||
|
||||
# [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
|
||||
#~ For building the objects files "-ffunction-sections -fdata-sections" was missing
|
||||
#~ and the final avr-gcc call needs "-Wl,--gc-section".
|
||||
CXSECTF = -fno-exceptions -ffunction-sections -fdata-sections
|
||||
CFINALF = -Wl,--gc-section
|
||||
|
||||
CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CCWARN) $(CSTANDARD) $(CEXTRA)
|
||||
# added CWARN also to .cpp
|
||||
CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CXSECTF)
|
||||
CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CEXTRA) $(CTUNING)
|
||||
CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) -Wall $(CEXTRA) $(CTUNING)
|
||||
#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs
|
||||
LDFLAGS = -lm
|
||||
|
||||
|
||||
# Programming support using avrdude. Settings and variables.
|
||||
AVRDUDE_PORT = $(PORT)
|
||||
AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
|
||||
AVRDUDE_FLAGS = -V -F \
|
||||
-p $(BUILD_MCU) -P $(AVRDUDE_PORT) -c $(UPLOAD_PROTOCOL) \
|
||||
-b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avrdude.conf
|
||||
# -b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf
|
||||
AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex:i
|
||||
AVRDUDE_FLAGS = -D -C $(INSTALL_DIR)/hardware/tools/avrdude.conf \
|
||||
-p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
|
||||
-b $(UPLOAD_RATE)
|
||||
|
||||
# Program settings
|
||||
CC = $(AVR_TOOLS_PATH)/avr-gcc
|
||||
CXX = $(AVR_TOOLS_PATH)/avr-g++
|
||||
OBJCOPY = $(AVR_TOOLS_PATH)/avr-objcopy
|
||||
OBJDUMP = $(AVR_TOOLS_PATH)/avr-objdump
|
||||
AR = $(AVR_TOOLS_PATH)/avr-ar
|
||||
SIZE = $(AVR_TOOLS_PATH)/avr-size
|
||||
NM = $(AVR_TOOLS_PATH)/avr-nm
|
||||
#~ AVRDUDE = $(AVR_TOOLS_PATH)/avrdude
|
||||
AVRDUDE = $(AVR_DUDE_PATH)/avrdude
|
||||
CC = $(AVR_TOOLS_PATH)avr-gcc
|
||||
CXX = $(AVR_TOOLS_PATH)avr-g++
|
||||
OBJCOPY = $(AVR_TOOLS_PATH)avr-objcopy
|
||||
OBJDUMP = $(AVR_TOOLS_PATH)avr-objdump
|
||||
AR = $(AVR_TOOLS_PATH)avr-ar
|
||||
SIZE = $(AVR_TOOLS_PATH)avr-size
|
||||
NM = $(AVR_TOOLS_PATH)avr-nm
|
||||
AVRDUDE = avrdude
|
||||
REMOVE = rm -f
|
||||
MV = mv -f
|
||||
|
||||
# Define all object files.
|
||||
# NOTE: obj files will be created in respective src directories (libraries or $(INSTALL_DIR));
|
||||
# make clean deletes them fine
|
||||
# note that srcs are in libraries or other directories;
|
||||
# $(CXXSRC:.cpp=.o) will cause obj files to be in same loc as src files
|
||||
#~ OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
|
||||
# to change the output directory for object files;
|
||||
# must change the obj list here!
|
||||
# and then, match to corresponding rule somehow?
|
||||
# or leave this - and parse in rule (auth automatic variable $(@F))?
|
||||
# "Suffix Replacement"
|
||||
CXXSRC+=MarlinSerial.cpp SdBaseFile.cpp stepper.cpp motion_control.cpp SdFatUtil.cpp temperature.cpp planner.cpp SdFile.cpp Sd2Card.cpp SdVolume.cpp
|
||||
OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
|
||||
|
||||
# added - OBJ list, transformed into applet/
|
||||
OBJT = $(addprefix applet/,$(notdir $(OBJ)))
|
||||
ALLSRC = $(SRC) $(CXXSRC) $(ASRC)
|
||||
|
||||
# Define all listing files.
|
||||
LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
|
||||
|
||||
# Combine all necessary flags and optional flags.
|
||||
# Add target processor to flags.
|
||||
ALL_CFLAGS = -mmcu=$(BUILD_MCU) -I. $(CFLAGS)
|
||||
ALL_CXXFLAGS = -mmcu=$(BUILD_MCU) -I. $(CXXFLAGS)
|
||||
ALL_ASFLAGS = -mmcu=$(BUILD_MCU) -I. -x assembler-with-cpp $(ASFLAGS)
|
||||
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
|
||||
ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
|
||||
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
|
||||
|
||||
# depended libraries of .pde need to be added from
|
||||
# $(INSTALL_DIR)/libraries (TODO: and/or ~/sketchbook/libraries)
|
||||
# grep for 'include', test if exists, add...
|
||||
# note: prefix "a real tab character" http://www.delorie.com/djgpp/doc/ug/larger/makefiles.html
|
||||
# $$ to escape $ for shell;
|
||||
# note: must NOT put comments # inside bash execution;
|
||||
# those would get removed by make; making shell see "EOF in backquote substitution"
|
||||
# echo $$ix ; \
|
||||
# 'shell' twice - for each subprocess! Backtick doesn't get expanded?
|
||||
GREPRES:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
|
||||
if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
|
||||
LINCS="$$LINCS -I$(INSTALL_DIR)/libraries/$$ix" ;\
|
||||
fi; \
|
||||
done; \
|
||||
echo $$LINCS)
|
||||
# append includes:
|
||||
CINCS += $(GREPRES)
|
||||
CXXINCS += $(GREPRES)
|
||||
# append library source .cpp files too (CXXSRC)
|
||||
GREPRESB:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
|
||||
if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
|
||||
CPPSRCS="$$CPPSRCS $(INSTALL_DIR)/libraries/$$ix/*.cpp" ;\
|
||||
fi; \
|
||||
done; \
|
||||
echo $$CPPSRCS)
|
||||
CXXSRC += $(GREPRESB)
|
||||
# added - only CXX obj from libraries:
|
||||
CXXLIBOBJ = $(GREPRESB:.cpp=.o)
|
||||
|
||||
# Default target.
|
||||
all: applet_files build sizeafter
|
||||
all: build sizeafter
|
||||
|
||||
build: elf hex
|
||||
|
||||
applet_files: $(TARGET).pde
|
||||
applet/$(TARGET).cpp: $(TARGET).pde $(MAKEFILE)
|
||||
# Here is the "preprocessing".
|
||||
# It creates a .cpp file based with the same name as the .pde file.
|
||||
# On top of the new .cpp file comes the WProgram.h header.
|
||||
@ -212,18 +145,11 @@ applet_files: $(TARGET).pde
|
||||
# Then the .cpp file will be compiled. Errors during compile will
|
||||
# refer to this new, automatically generated, file.
|
||||
# Not the original .pde file you actually edit...
|
||||
test -d applet || mkdir applet
|
||||
# @ supresses printout of the cmdline itself; so only the out of echo is printed
|
||||
@echo ALL OBJT: $(OBJT)
|
||||
@echo ALL CXXLIBOBJ: $(CXXLIBOBJ)
|
||||
# echo '#include "WProgram.h"' > applet/$(TARGET).cpp
|
||||
@echo "#include \"WProgram.h\"\nvoid setup();\nvoid loop();\n" > applet/$(TARGET).cpp
|
||||
##cat $(TARGET).pde >> applet/$(TARGET).cpp
|
||||
cat ${PDES}>> applet/$(TARGET).cpp
|
||||
cp *.cpp applet/
|
||||
# no more need to cat main.cpp (v0022) - now it is compiled in
|
||||
# cat $(ARDUINO)/main.cpp >> applet/$(TARGET).cpp
|
||||
|
||||
@echo " WR applet/$(TARGET).cpp"
|
||||
@test -d applet || mkdir applet
|
||||
@echo '#include "WProgram.h"' > applet/$(TARGET).cpp
|
||||
@cat $(TARGET).pde >> applet/$(TARGET).cpp
|
||||
@cat $(ARDUINO)/main.cpp >> applet/$(TARGET).cpp
|
||||
|
||||
elf: applet/$(TARGET).elf
|
||||
hex: applet/$(TARGET).hex
|
||||
@ -233,7 +159,10 @@ sym: applet/$(TARGET).sym
|
||||
|
||||
# Program the device.
|
||||
upload: applet/$(TARGET).hex
|
||||
stty hup < $(PORT); true
|
||||
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
|
||||
stty -hup < $(PORT); true
|
||||
|
||||
|
||||
# Display size of file.
|
||||
HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex
|
||||
@ -242,7 +171,8 @@ sizebefore:
|
||||
@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi
|
||||
|
||||
sizeafter:
|
||||
@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi
|
||||
@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); echo; fi
|
||||
|
||||
|
||||
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
|
||||
COFFCONVERT=$(OBJCOPY) --debugging \
|
||||
@ -251,16 +181,21 @@ COFFCONVERT=$(OBJCOPY) --debugging \
|
||||
--change-section-address .noinit-0x800000 \
|
||||
--change-section-address .eeprom-0x810000
|
||||
|
||||
|
||||
coff: applet/$(TARGET).elf
|
||||
$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof
|
||||
|
||||
|
||||
extcoff: $(TARGET).elf
|
||||
$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof
|
||||
|
||||
|
||||
.SUFFIXES: .elf .hex .eep .lss .sym
|
||||
.PRECIOUS: .o
|
||||
|
||||
.elf.hex:
|
||||
$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
|
||||
@echo " COPY $@"
|
||||
@$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
|
||||
|
||||
.elf.eep:
|
||||
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
|
||||
@ -275,78 +210,39 @@ extcoff: $(TARGET).elf
|
||||
$(NM) -n $< > $@
|
||||
|
||||
# Link: create ELF output file from library.
|
||||
# NOTE: applet/$(TARGET).cpp.o MUST BE BEFORE applet/core.a
|
||||
# in the dependency list, so its rule runs first!
|
||||
applet/$(TARGET).elf: $(TARGET).pde applet/$(TARGET).cpp.o applet/core.a
|
||||
# $(CC) $(ALL_CFLAGS) -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
|
||||
# changed as in IDE v0022: link cpp obj files
|
||||
@echo $$(tput bold)$$(tput setaf 2) $(CC) $$(tput sgr0) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
|
||||
echo ${OBJT}
|
||||
#$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/$(TARGET).cpp.o -L. applet/core.a $(LDFLAGS)
|
||||
$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ ${LINKORDER} $(LDFLAGS)
|
||||
#@$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/*.o applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
|
||||
applet/$(TARGET).elf: applet/$(TARGET).cpp applet/core.a Configuration.h
|
||||
@echo " CXX $@"
|
||||
@$(CC) $(ALL_CXXFLAGS) -Wl,--gc-sections -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
|
||||
|
||||
# added: cpp.o depends on cpp (and .pde which generates it)
|
||||
# $< "first item in the dependencies list"; $@ "left side of the :"; $^ "right side of the :"
|
||||
# http://www.cs.colby.edu/maxwell/courses/tutorials/maketutor/
|
||||
applet/$(TARGET).cpp.o: applet/$(TARGET).cpp
|
||||
@echo $$(tput bold) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $< -o $@
|
||||
applet/core.a: $(OBJ) Configuration.h
|
||||
@for i in $(OBJ); do echo " AR $$i"; $(AR) rcs applet/core.a $$i; done
|
||||
|
||||
%.o: %.c Configuration.h $(MAKEFILE)
|
||||
@echo " CC $@"
|
||||
@$(CC) -c $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
%.o: %.cpp Configuration.h $(MAKEFILE)
|
||||
@echo " CXX $@"
|
||||
@$(CXX) -c $(ALL_CXXFLAGS) $< -o $@
|
||||
|
||||
#~ applet/core.a: $(OBJ)
|
||||
#~ @for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
|
||||
|
||||
applet/core.a: $(OBJT)
|
||||
@for i in $(OBJT); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
|
||||
|
||||
# iterate through OBJ to find the original location; then build depending on source extension
|
||||
# TODO: add handling of assembler files
|
||||
applet/%.o:
|
||||
@for iob in $(OBJ); do \
|
||||
if [ "`basename $$iob`" = "`basename $@`" ]; then \
|
||||
for ios in $(ALLSRC); do \
|
||||
if [ "$${iob%%.*}" = "$${ios%%.*}" ]; then \
|
||||
case $${ios##*.} in \
|
||||
"cpp") \
|
||||
echo "$$(tput bold)$$(tput setaf 1) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $$ios -o $@"; \
|
||||
$(CXX) -c $(ALL_CXXFLAGS) $$ios -o $@;; \
|
||||
"c") \
|
||||
echo "$$(tput bold)$$(tput setaf 1) $(CC) $$(tput sgr0) -c $(ALL_CFLAGS) $$ios -o $@"; \
|
||||
$(CC) -c $(ALL_CFLAGS) $$ios -o $@;; \
|
||||
esac; \
|
||||
fi; \
|
||||
done; \
|
||||
fi; \
|
||||
done;
|
||||
|
||||
#~ # Compile: create object files from C++ source files.
|
||||
#~ .cpp.o:
|
||||
#~ $(CXX) -c $(ALL_CXXFLAGS) $< -o $@
|
||||
|
||||
#~ # Compile: create object files from C source files.
|
||||
#~ .c.o:
|
||||
#~ $(CC) -c $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
#~ # Compile: create assembler files from C source files.
|
||||
#~ .c.s:
|
||||
#~ $(CC) -S $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
#~ # Assemble: create object files from assembler source files.
|
||||
#~ .S.o:
|
||||
#~ $(CC) -c $(ALL_ASFLAGS) $< -o $@
|
||||
|
||||
#~ # Automatic dependencies
|
||||
#~ %.d: %.c
|
||||
#~ $(CC) -M $(ALL_CFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
|
||||
|
||||
#~ %.d: %.cpp
|
||||
#~ $(CXX) -M $(ALL_CXXFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
|
||||
|
||||
# Target: clean project.
|
||||
clean:
|
||||
$(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \
|
||||
applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \
|
||||
$(OBJT) applet/$(TARGET).cpp.o \
|
||||
@echo " RM applet/*"
|
||||
@$(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \
|
||||
applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp applet/core.a \
|
||||
$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
|
||||
@echo " RMDIR applet/"
|
||||
@rmdir applet
|
||||
|
||||
.PHONY: all build elf hex eep lss sym program coff extcoff clean applet_files sizebefore sizeafter
|
||||
depend:
|
||||
if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
|
||||
then \
|
||||
sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
|
||||
$(MAKEFILE).$$$$ && \
|
||||
$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
|
||||
fi
|
||||
echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
|
||||
>> $(MAKEFILE); \
|
||||
$(CC) -M -mmcu=$(MCU) $(CDEFS) $(CINCS) $(SRC) $(ASRC) >> $(MAKEFILE)
|
||||
|
||||
.PHONY: all build elf hex eep lss sym program coff extcoff clean depend applet_files sizebefore sizeafter
|
||||
|
||||
@ -841,11 +841,11 @@ void process_commands()
|
||||
/* continue to loop until we have reached the target temp
|
||||
_and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */
|
||||
while((residencyStart == -1) ||
|
||||
(residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000l) ) {
|
||||
(residencyStart >= 0 && (((unsigned int) (millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))) ) {
|
||||
#else
|
||||
while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) {
|
||||
#endif //TEMP_RESIDENCY_TIME
|
||||
if((millis() - codenum) > 1000 )
|
||||
if( (millis() - codenum) > 1000UL )
|
||||
{ //Print Temp Reading and remaining time every 1 second while heating up/cooling down
|
||||
SERIAL_PROTOCOLPGM("T:");
|
||||
SERIAL_PROTOCOL( degHotend(tmp_extruder) );
|
||||
@ -855,7 +855,7 @@ void process_commands()
|
||||
SERIAL_PROTOCOLPGM(" W:");
|
||||
if(residencyStart > -1)
|
||||
{
|
||||
codenum = TEMP_RESIDENCY_TIME - ((millis() - residencyStart) / 1000);
|
||||
codenum = ((TEMP_RESIDENCY_TIME * 1000UL) - (millis() - residencyStart)) / 1000UL;
|
||||
SERIAL_PROTOCOLLN( codenum );
|
||||
}
|
||||
else
|
||||
@ -938,14 +938,13 @@ void process_commands()
|
||||
|
||||
case 81: // M81 - ATX Power Off
|
||||
|
||||
#if (SUICIDE_PIN >-1)
|
||||
#if defined SUICIDE_PIN && SUICIDE_PIN > -1
|
||||
st_synchronize();
|
||||
suicide();
|
||||
#else
|
||||
#if (PS_ON_PIN > -1)
|
||||
#elif (PS_ON_PIN > -1)
|
||||
SET_INPUT(PS_ON_PIN); //Floating
|
||||
#endif
|
||||
#endif
|
||||
break;
|
||||
|
||||
case 82:
|
||||
axis_relative_modes[3] = false;
|
||||
@ -1304,6 +1303,7 @@ void manage_inactivity(byte debug)
|
||||
disable_e0();
|
||||
disable_e1();
|
||||
disable_e2();
|
||||
#endif
|
||||
}
|
||||
}
|
||||
#ifdef EXTRUDER_RUNOUT_PREVENT
|
||||
|
||||
@ -1,5 +1,8 @@
|
||||
#include "Marlin.h"
|
||||
#include "cardreader.h"
|
||||
#include "ultralcd.h"
|
||||
#include "stepper.h"
|
||||
#include "temperature.h"
|
||||
#ifdef SDSUPPORT
|
||||
|
||||
|
||||
@ -1,6 +1,49 @@
|
||||
#ifndef PINS_H
|
||||
#define PINS_H
|
||||
|
||||
#if MOTHERBOARD == 99
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#define X_STEP_PIN 2
|
||||
#define X_DIR_PIN 3
|
||||
#define X_ENABLE_PIN -1
|
||||
#define X_MIN_PIN -1
|
||||
#define X_MAX_PIN 16
|
||||
|
||||
#define Y_STEP_PIN 5
|
||||
#define Y_DIR_PIN 6
|
||||
#define Y_ENABLE_PIN -1
|
||||
#define Y_MIN_PIN 67
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 62
|
||||
#define Z_DIR_PIN 63
|
||||
#define Z_ENABLE_PIN -1
|
||||
#define Z_MIN_PIN 59
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 65
|
||||
#define E0_DIR_PIN 66
|
||||
#define E0_ENABLE_PIN -1
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 53
|
||||
#define LED_PIN -1
|
||||
#define FAN_PIN -1
|
||||
#define PS_ON_PIN 9
|
||||
#define KILL_PIN -1
|
||||
|
||||
#define HEATER_0_PIN 13
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define TEMP_0_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define TEMP_1_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define HEATER_BED_PIN 4
|
||||
#define TEMP_BED_PIN 10
|
||||
|
||||
#endif /* 99 */
|
||||
|
||||
/****************************************************************************************
|
||||
* Arduino pin assignment
|
||||
*
|
||||
|
||||
@ -85,9 +85,9 @@ static unsigned long previous_millis_bed_heater;
|
||||
static unsigned char soft_pwm[EXTRUDERS];
|
||||
|
||||
#ifdef WATCHPERIOD
|
||||
static int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
|
||||
static int watch_oldtemp[3] = {0,0,0};
|
||||
static unsigned long watchmillis = 0;
|
||||
int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
|
||||
int watch_oldtemp[3] = {0,0,0};
|
||||
unsigned long watchmillis = 0;
|
||||
#endif //WATCHPERIOD
|
||||
|
||||
// Init min and max temp with extreme values to prevent false errors during startup
|
||||
@ -218,7 +218,7 @@ void manage_heater()
|
||||
|
||||
#ifdef WATCHPERIOD
|
||||
if(watchmillis && millis() - watchmillis > WATCHPERIOD){
|
||||
if(watch_oldtemp[TEMPSENSOR_HOTEND_0] >= degHotend(active_extruder)){
|
||||
if(watch_oldtemp[0] >= degHotend(active_extruder)){
|
||||
setTargetHotend(0,active_extruder);
|
||||
LCD_MESSAGEPGM("Heating failed");
|
||||
SERIAL_ECHO_START;
|
||||
@ -556,7 +556,7 @@ void setWatch()
|
||||
for (int e = 0; e < EXTRUDERS; e++)
|
||||
{
|
||||
if(isHeatingHotend(e))
|
||||
watch_oldtemp[TEMPSENSOR_HOTEND_0] = degHotend(0);
|
||||
watch_oldtemp[0] = degHotend(0);
|
||||
{
|
||||
t = max(t,millis());
|
||||
watch_raw[e] = current_raw[e];
|
||||
|
||||
Loading…
Reference in New Issue
Block a user