diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index eb209befb1..e74c1afde3 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -221,20 +221,20 @@ // The minimal temperature defines the temperature below which the heater will not be enabled It is used // to check that the wiring to the thermistor is not broken. // Otherwise this would lead to the heater being powered on all the time. -#define HEATER_0_MINTEMP 5 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define HEATER_3_MINTEMP 5 -#define BED_MINTEMP 5 +#define HEATER_0_MINTEMP 15 +//#define HEATER_1_MINTEMP 5 +//#define HEATER_2_MINTEMP 5 +//#define HEATER_3_MINTEMP 5 +//#define BED_MINTEMP 5 // When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection. #define HEATER_0_MAXTEMP 250 -#define HEATER_1_MAXTEMP 275 -#define HEATER_2_MAXTEMP 275 -#define HEATER_3_MAXTEMP 275 -#define BED_MAXTEMP 150 +//#define HEATER_1_MAXTEMP 275 +//#define HEATER_2_MAXTEMP 275 +//#define HEATER_3_MAXTEMP 275 +//#define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R @@ -293,7 +293,7 @@ // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current +//#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) @@ -344,7 +344,7 @@ */ #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders -#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +//#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed //=========================================================================== //============================= Mechanical Settings ========================= @@ -512,7 +512,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // For M851 give a range for adjusting the Z probe offset // -#define Z_PROBE_OFFSET_RANGE_MIN -5 +#define Z_PROBE_OFFSET_RANGE_MIN -2 #define Z_PROBE_OFFSET_RANGE_MAX 0 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 @@ -561,8 +561,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Y_HOME_DIR -1 #define Z_HOME_DIR -1 -#define min_software_endstops false // If true, axis won't move to coordinates less than HOME_POS. -#define max_software_endstops false // If true, axis won't move to coordinates greater than the defined lengths below. +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // @section machine @@ -715,18 +715,18 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // default settings -#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 204.146} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {200, 200, 3.3, 200} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1000, 1000, 100, 3000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. +#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 203} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {250, 250, 2, 200} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {1000, 1000, 20, 1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) -#define DEFAULT_XYJERK 15.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 2.0 // (mm/sec) +#define DEFAULT_XYJERK 10.0 // (mm/sec) +#define DEFAULT_ZJERK 0.4 // (mm/sec) +#define DEFAULT_EJERK 2.0 // (mm/sec) //============================================================================= @@ -809,7 +809,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // - Total time printing // // This information can be viewed by the M78 command. -//#define PRINTCOUNTER +#define PRINTCOUNTER //============================================================================= //============================= LCD and SD support ============================ @@ -889,7 +889,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // Use CRC checks and retries on the SD communication. // -//#define SD_CHECK_AND_RETRY +#define SD_CHECK_AND_RETRY // // ENCODER SETTINGS diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index b52f32cfd9..74a22c17dd 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -286,7 +286,7 @@ //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. // When G28 is called, this option will make Y home before X -//#define HOME_Y_BEFORE_X +#define HOME_Y_BEFORE_X // @section machine @@ -301,7 +301,7 @@ // Default stepper release if idle. Set to 0 to deactivate. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. // Time can be set by M18 and M84. -#define DEFAULT_STEPPER_DEACTIVE_TIME 60 +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 #define DISABLE_INACTIVE_X true #define DISABLE_INACTIVE_Y true #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. @@ -333,7 +333,7 @@ // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end // of the buffer and all stops. This should not be much greater than zero and should only be changed // if unwanted behavior is observed on a user's machine when running at very slow speeds. -#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec) +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec) // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. #define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16] @@ -355,12 +355,12 @@ //=============================Additional Features=========================== //=========================================================================== -#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly -#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value -#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value +//#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +//#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +//#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ -#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again +//#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again // @section lcd @@ -374,7 +374,7 @@ #define SD_DETECT_INVERTED #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? - #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. + #define SD_FINISHED_RELEASECOMMAND "M104 S0\nM84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that. diff --git a/Marlin/example_configurations/Hephestos_2/readme.md b/Marlin/example_configurations/Hephestos_2/readme.md index 19521705fe..447022c94d 100644 --- a/Marlin/example_configurations/Hephestos_2/readme.md +++ b/Marlin/example_configurations/Hephestos_2/readme.md @@ -5,4 +5,8 @@ NOTE: The look and feel of the Hephestos 2 while navigating the LCD menu will ch ## Changelog * 2016/03/01 - Initial release - * 2016/03/21 - Activated four point auto leveling by default; updated miscellaneous z-probe values + * 2016/03/21 - Activated 4-point auto leveling by default + Updated miscellaneous z-probe values + * 2016/06/21 - Disabled hot bed related options + Activated software endstops + SD printing now disables the heater when finished