From 292e83466e356ae4a21bd5c85745535d50e332f6 Mon Sep 17 00:00:00 2001 From: Foxies Date: Wed, 18 Nov 2020 05:32:34 +0100 Subject: [PATCH] FLSun Hispeedv1 Board update (#19959) Co-authored-by: Scott Lahteine --- Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h | 188 +++++++++---------- 1 file changed, 86 insertions(+), 102 deletions(-) diff --git a/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h index a056aa96e5..05b8b19a8a 100644 --- a/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h +++ b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h @@ -50,15 +50,16 @@ // #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) #define FLASH_EEPROM_EMULATION - #define EEPROM_PAGE_SIZE (0x800U) // 2KB + #define EEPROM_PAGE_SIZE (0x800U) // 2KB #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2KB #endif +// // SPI // Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface. // -#define SPI_DEVICE 2 +#define SPI_DEVICE 2 // SPI Flash #define HAS_SPI_FLASH 1 @@ -108,49 +109,26 @@ #define E0_STEP_PIN PD6 // E0_STEP #define E0_DIR_PIN PD3 // E0_DIR +/** + * FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers. + * Several wiring options are provided below, defaulting to + * to the most compatible. + */ + // // Drivers // #if HAS_TMC220x - - #if ENABLED(HARDWARE_SERIAL) /* TMC2209 */ - #define X_SLAVE_ADDRESS 3 // | | : - #define Y_SLAVE_ADDRESS 2 // : | : - #define Z_SLAVE_ADDRESS 1 // | : : - //#define E0_SLAVE_ADDRESS 0 // : : : - - #define X_SERIAL_TX_PIN PA9 // TXD1 - #define X_SERIAL_RX_PIN PA9 // TXD1 - - #define Y_SERIAL_TX_PIN PA9 // TXD1 - #define Y_SERIAL_RX_PIN PA9 // TXD1 - - #define Z_SERIAL_TX_PIN PA9 // TXD1 - #define Z_SERIAL_RX_PIN PA9 // TXD1 - - #elif ENABLED(SOFTWARE_SERIAL) /* TMC220x */ - /** - * TMC2208 stepper UART-configurable by PDN_UART pin - * Software serial - */ - #define X_SLAVE_ADDRESS 0 - #define Y_SLAVE_ADDRESS 0 - #define Z_SLAVE_ADDRESS 0 - - #define X_SERIAL_TX_PIN PA10 // RXD1 - #define X_SERIAL_RX_PIN PA10 // RXD1 - - #define Y_SERIAL_TX_PIN PA9 // TXD1 - #define Y_SERIAL_RX_PIN PA9 // TXD1 - - #define Z_SERIAL_TX_PIN PC7 // IO1 - #define Z_SERIAL_RX_PIN PC7 // IO1 - - #endif - // Reduce baud rate to improve software serial reliability - #define TMC_BAUD_RATE 19200 + // SoftwareSerial with one pin per driver + // Compatible with TMC2208 and TMC2209 drivers + #define X_SERIAL_TX_PIN PA10 // RXD1 + #define X_SERIAL_RX_PIN PA10 // RXD1 + #define Y_SERIAL_TX_PIN PA9 // TXD1 + #define Y_SERIAL_RX_PIN PA9 // TXD1 + #define Z_SERIAL_TX_PIN PC7 // IO1 + #define Z_SERIAL_RX_PIN PC7 // IO1 + #define TMC_BAUD_RATE 19200 #else - // Motor current PWM pins #define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY #define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z @@ -159,33 +137,33 @@ #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 } #endif - /** - * src: MKS Robin_Mini V2 - * __ESP(M1)__ -J1- - * GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) // - * | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating - * IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating) - * IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating) - * IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run - * | nc | | nc | (01)=>WIFI_CTRL(PA5) - * RX| 21 | | nc | - * TX| 22 | | 01 |RST - * ￣￣ AE￣￣ - * - */ - #ifdef ESP_WIFI - #define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN - #define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN - #define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN - #endif +/** + * MKS Robin_Wifi or another ESP8266 module + * + * __ESP(M1)__ -J1- + * GND| 15 | | 08 |+3v3 (22) RXD1 (PA10) + * | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating + * IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating) + * IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating) + * IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run + * | nc | | nc | (01) WIFI_CTRL (PA5) + * RX| 21 | | nc | + * TX| 22 | | 01 |RST + * ￣￣ AE￣￣ + */ + // Module ESP-WIFI + #define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this + #define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2 + #define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST + #define ESP_WIFI_MODULE_ENABLE_PIN -1 + #define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN + #define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN #endif // // EXTRUDER // -#if AXIS_DRIVER_TYPE(E0,TMC2208)||AXIS_DRIVER_TYPE(E0,TMC2209) - #define E0_SLAVE_ADDRESS 0 - +#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209) #define E0_SERIAL_TX_PIN PA8 // IO0 #define E0_SERIAL_RX_PIN PA8 // IO0 #define TMC_BAUD_RATE 19200 @@ -199,7 +177,7 @@ #endif // -// Temperature Sensors(THM) +// Temperature Sensors (THM) // #define TEMP_0_PIN PC1 // TEMP_E0 #define TEMP_BED_PIN PC0 // TEMP_BED @@ -211,7 +189,6 @@ #define HEATER_BED_PIN PA0 // HEATER_BED-WKUP #define FAN_PIN PB1 // E_FAN -//#define CONTROLLER_FAN_PIN PD6 // BOARD FAN // // Misc. Functions @@ -221,12 +198,24 @@ #define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC #endif +/** + * Connector J2 + * ------- + * DIO O|1 2|O 3v3 + * CSK O|3 5|O GND + * RST O|5 6|O GND + * ------- + */ +//#define SW_DIO PA13 +//#define SW_CLK PA14 +//#define SW_RST NRST // (14) + // // Power Supply Control // #if ENABLED(PSU_CONTROL) #define KILL_PIN PA2 // PW_DET - #define KILL_PIN_INVERTING true // + #define KILL_PIN_INVERTING true //#define PS_ON_PIN PA3 // PW_CN /PW_OFF #endif @@ -240,28 +229,33 @@ //#define LED_PIN PB2 // BOOT1 #if ENABLED(NEOPIXEL_LED) - #define LED_PWM PA8 + #define LED_PWM PC7 // IO1 #ifndef NEOPIXEL_PIN - #define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1/TX/RX PIN + #define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN #endif #endif -//Others test. -//#define SERVO0_PIN PA5 // WIFI CRTL -//#define GPIO_CLEAR PA8 // IO0 -//#define GPIO_SET PA5 - // // SD Card // -#define SDIO_SUPPORT -#define SDIO_CLOCK 4500000 // 4.5 MHz /* 18 MHz (18000000) or 4.5MHz (450000) */ -//#define SDIO_CLOCK 18000000 // 18 MHz (18000000) -#if ENABLED(SDIO_SUPPORT) - #define SCK_PIN PB13 // SPI2 - #define MISO_PIN PB14 // SPI2 - #define MOSI_PIN PB15 // SPI2 - #define SD_DETECT_PIN PD12 // SD_CD +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +// Use the on-board card socket labeled SD_Extender +#if SD_CONNECTION_IS(CUSTOM_CABLE) + #define SCK_PIN PC12 + #define MISO_PIN PC8 + #define MOSI_PIN PD2 + #define SS_PIN -1 + #define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection) +#else + #define SDIO_SUPPORT + #define SDIO_CLOCK 4500000 // 4.5 MHz + #define SDIO_READ_RETRIES 16 + #define ONBOARD_SPI_DEVICE 1 // SPI1 + #define ONBOARD_SD_CS_PIN PC11 + #define SD_DETECT_PIN -1 // SD_CD (-1 active refresh) #endif // @@ -271,6 +265,10 @@ #define BEEPER_PIN PC5 #endif +#if ENABLED(SPEAKER) && BEEPER_PIN == PC5 + #error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER." +#endif + /** * Note: MKS Robin TFT screens use various TFT controllers * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240) @@ -284,26 +282,7 @@ * because Marlin uses the reset as a failsafe to revive a glitchy LCD. */ -// MKS Robin TFT v2.0 with ILI9341 -// Read display identification information (0xD3 on ILI9341) -//#define TOUCH_CALIBRATION_X 12013 -//#define TOUCH_CALIBRATION_Y -8711 -//#define TOUCH_OFFSET_X -32 -//#define TOUCH_OFFSET_Y 256 - -// MKS Robin TFT v1.1 with ILI9328 -//#define TOUCH_CALIBRATION_X -11792 -//#define TOUCH_CALIBRATION_Y 8947 -//#define TOUCH_OFFSET_X 342 -//#define TOUCH_OFFSET_Y -19 - -// MKS Robin TFT v1.1 with R61505 -//#define TOUCH_CALIBRATION_X 12489 -//#define TOUCH_CALIBRATION_Y 9210 -//#define TOUCH_OFFSET_X -52 -//#define TOUCH_OFFSET_Y -17 - -// QQS-Pro uses MKS Robin TFT v2.0 +// QQS-Pro uses MKS Robin TFT v2.0 320x240 // Shared FSMC Configs #if HAS_FSMC_TFT @@ -320,8 +299,13 @@ #define FSMC_DMA_DEV DMA2 #define FSMC_DMA_CHANNEL DMA_CH5 - #define TOUCH_BUTTONS_HW_SPI - #define TOUCH_BUTTONS_HW_SPI_DEVICE 2 + #define TFT_BUFFER_SIZE 14400 + #if ENABLED(TFT_CLASSIC_UI) + #define TFT_MARLINBG_COLOR 0x3186 // White + #define TFT_MARLINUI_COLOR 0xC7B6 // green + #define TFT_BTARROWS_COLOR 0xDEE6 // Yellow + #define TFT_BTOKMENU_COLOR 0x145F // Cyan + #endif #endif #if NEED_TOUCH_PINS