diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 4aff7fe099..9db8dee5f4 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -37,6 +37,8 @@ // 7 = Ultimaker // 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) // 8 = Teensylu +// 81 = Printrboard (AT90USB1286) +// 82 = Brainwave (AT90USB646) // 9 = Gen3+ // 70 = Megatronics // 90 = Alpha OMCA board diff --git a/Marlin/pins.h b/Marlin/pins.h index febe2cd1f3..f61f534d04 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -1015,6 +1015,206 @@ #endif #endif +/**************************************************************************************** +* Printrboard Rev. B pin assingments (ATMEGA90USB1286) +* Requires the Teensyduino software with Teensy++ 2.0 selected in arduino IDE! + http://www.pjrc.com/teensy/teensyduino.html +* See http://reprap.org/wiki/Printrboard for more info +****************************************************************************************/ +#if MOTHERBOARD == 81 +#define MOTHERBOARD 8 // Disable MarlinSerial etc. +#define KNOWN_BOARD 1 + +#ifndef __AVR_AT90USB1286__ +#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu. +#endif + +#define X_STEP_PIN 28 +#define X_DIR_PIN 29 +#define X_ENABLE_PIN 19 +#define X_MIN_PIN 47 +#define X_MAX_PIN -1 + +#define Y_STEP_PIN 30 +#define Y_DIR_PIN 31 +#define Y_ENABLE_PIN 18 +#define Y_MIN_PIN 20 +#define Y_MAX_PIN -1 + +#define Z_STEP_PIN 32 +#define Z_DIR_PIN 33 +#define Z_ENABLE_PIN 17 +#define Z_MIN_PIN 36 +#define Z_MAX_PIN -1 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 35 +#define E0_ENABLE_PIN 13 + +#define HEATER_0_PIN 15 // Extruder +#define HEATER_1_PIN -1 +#define HEATER_2_PIN -1 +#define HEATER_BED_PIN 14 // Bed +#define FAN_PIN 16 // Fan + +#define TEMP_0_PIN 1 // Extruder - ANALOG PIN NUMBERING +#define TEMP_1_PIN -1 +#define TEMP_2_PIN -1 +#define TEMP_BED_PIN 0 // Bed - ANALOG PIN NUMBERING + +#define SDPOWER -1 +#define SDSS 26 +#define LED_PIN -1 +#define PS_ON_PIN -1 +#define KILL_PIN -1 + +#ifndef SDSUPPORT +// these pins are defined in the SD library if building with SD support + #define SCK_PIN 21 + #define MISO_PIN 22 + #define MOSI_PIN 23 +#endif + +#ifdef ULTRA_LCD + + #ifdef NEWPANEL + //arduino pin which triggers an piezzo beeper + #define BEEPER 33 // Beeper on AUX-4 + +#ifndef MCP28017_LCD + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 +#endif // MCP28017_LCD + + //buttons are directly attached using AUX-2 + #define BTN_EN1 11 // PC1 + #define BTN_EN2 12 // PC2 +#ifndef VERSAPANEL + #define BTN_ENC 31 //the click +#endif + + #define BLEN_C 2 + #define BLEN_B 1 + #define BLEN_A 0 + + #define SDCARDDETECT -1 // Ramps does not use this port + + //encoder rotation values + #define encrot0 0 + #define encrot1 2 + #define encrot2 3 + #define encrot3 1 + + #else //old style panel with shift register + //arduino pin witch triggers an piezzo beeper + #define BEEPER 33 No Beeper added + + //buttons are attached to a shift register + // Not wired this yet + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 + + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + //encoder rotation values + #define encrot0 0 + #define encrot1 2 + #define encrot2 3 + #define encrot3 1 + + //bits in the shift register that carry the buttons for: + // left up center down right red + #define BL_LE 7 + #define BL_UP 6 + #define BL_MI 5 + #define BL_DW 4 + #define BL_RI 3 + #define BL_ST 2 + + #define BLEN_B 1 + #define BLEN_A 0 + #endif +#endif //ULTRA_LCD + +#endif + +/**************************************************************************************** + * Brainwave 1.0 pin assignments (AT90USB646) + * Requires hardware bundle for Arduino: + https://github.com/unrepentantgeek/brainwave-arduino + ****************************************************************************************/ +#if MOTHERBOARD == 82 +#define MOTHERBOARD 8 // Disable MarlinSerial etc. +#define KNOWN_BOARD 1 + +#ifndef __AVR_AT90USB646__ +#error Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu. +#endif + +#define X_STEP_PIN 27 +#define X_DIR_PIN 29 +#define X_ENABLE_PIN 28 +#define X_MIN_PIN 7 +#define X_MAX_PIN -1 +#define X_ATT_PIN 26 + +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 32 +#define Y_MIN_PIN 6 +#define Y_MAX_PIN -1 +#define Y_ATT_PIN 30 + +#define Z_STEP_PIN 17 +#define Z_DIR_PIN 19 +#define Z_ENABLE_PIN 18 +#define Z_MIN_PIN 5 +#define Z_MAX_PIN -1 +#define Z_ATT_PIN 16 + +#define E0_STEP_PIN 21 +#define E0_DIR_PIN 23 +#define E0_ENABLE_PIN 22 +#define E0_ATT_PIN 20 + +#define HEATER_0_PIN 4 // Extruder +#define HEATER_1_PIN -1 +#define HEATER_2_PIN -1 +#define HEATER_BED_PIN 38 // Bed +#define FAN_PIN 3 // Fan + +#define TEMP_0_PIN 7 // Extruder / Analog pin numbering +#define TEMP_1_PIN -1 +#define TEMP_2_PIN -1 +#define TEMP_BED_PIN 6 // Bed / Analog pin numbering + +#define SDPOWER -1 +#define SDSS -1 +#define LED_PIN 39 +#define PS_ON_PIN -1 +#define KILL_PIN -1 +#define ALARM_PIN -1 + +#ifndef SDSUPPORT +// these pins are defined in the SD library if building with SD support + #define SCK_PIN 21 + #define MISO_PIN 22 + #define MOSI_PIN 23 +#endif + +#endif + /**************************************************************************************** * Gen3+ pin assignment *