diff --git a/Marlin/src/pins/pins_COHESION3D_REMIX.h b/Marlin/src/pins/pins_COHESION3D_REMIX.h index 00b6714cea..29979792ef 100644 --- a/Marlin/src/pins/pins_COHESION3D_REMIX.h +++ b/Marlin/src/pins/pins_COHESION3D_REMIX.h @@ -139,11 +139,11 @@ // #if ENABLED(SPINDLE_LASER_ENABLE) #undef HEATER_0_PIN - #define SPINDLE_LASER_ENA_PIN P2_07 // FET 1 #undef HEATER_BED_PIN - #define SPINDLE_LASER_PWM_PIN P2_05 // Bed FET #undef FAN_PIN - #define SPINDLE_DIR_PIN P2_06 // FET 4 + #define SPINDLE_LASER_ENA_PIN P2_07 // FET 1 + #define SPINDLE_LASER_PWM_PIN P2_05 // Bed FET + #define SPINDLE_DIR_PIN P2_06 // FET 4 #endif // @@ -153,41 +153,134 @@ // defined to use the REPRAP_DISCOUNT_SMART_CONTROLLER. // // A remote SD card is currently not supported because the pins routed to the EXP2 -// connector are shared with the onboard SD card, and Marlin does not support reading -// G-code files from the onboard SD card. +// connector are shared with the onboard SD card, and Marlin does not support that +// hardware configuration. // -#if ENABLED(ULTRA_LCD) - #define BEEPER_PIN P1_31 // EXP1-1 - #define SD_DETECT_PIN P0_27 // EXP2-7 +#if ENABLED(FYSETC_MINI_12864) - #define BTN_EN1 P3_26 // EXP2-5 - #define BTN_EN2 P3_25 // EXP2-3 - #define BTN_ENC P1_30 // EXP1-2 + #define FORCE_SOFT_SPI // REQUIRED - results in LCD soft SPI mode 3 - #define LCD_PINS_RS P0_16 // EXP1-4 - #define LCD_SDSS P0_28 // EXP2-4 - #define LCD_PINS_ENABLE P0_18 // EXP1-3 - #define LCD_PINS_D4 P0_15 // EXP1-5 + #define BEEPER_PIN P1_31 // EXP1-1 + #define BTN_ENC P1_30 // EXP1-2 + #define DOGLCD_CS P0_18 // EXP1-3 + #define DOGLCD_A0 P0_16 // EXP1-4 + #define LCD_RESET_PIN P0_15 // EXP1-5 - #define KILL_PIN P2_11 // EXP2-10 + // A custom cable is REQUIRED for EXP2 cable because the SCK & MOSI on the card's EXP2 are dedicated + // to the onboard SD card. All required EXP2 signals come from the Ethernet connector. Pin 1 of this + // connector is the one nearest the motor power connector. + #define DOGLCD_SCK P1_17 // EXP2-2 => Ethernet pin 5 (bottom, 3 from left) + #define BTN_EN2 P1_09 // EXP2-3 => Ethernet pin 9 (bottom, 5 from left) + #define BTN_EN1 P1_04 // EXP2-5 => Ethernet pin 11 (bottom, 6 from left) + #define DOGLCD_MOSI P1_01 // EXP2-6 => Ethernet pin 13 (bottom, 7 from left) - #if ENABLED(SDSUPPORT) - #error "SDSUPPORT is not currently supported by the Cohesion3D boards" + // A custom EXP1 cable is required colored LEDs. Pins 1-5, 9, 10 of the cable go to pins 1-5, 9, 10 + // on the board's EXP1 connector. Pins 6, 7, and 8 of the EXP1 cable go to the Ethernet connector. + // Rev 1.2 displays do NOT require the RGB LEDs. 2.0 and 2.1 displays do require RGB. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left) + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_10 // EXP1-7 => Ethernet pin 10 (top row, 5 from left) + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_00 // EXP1-8 => Ethernet pin 12 (top row, 6 from left) + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left) #endif +#elif ENABLED(ULTRA_LCD) + + #define BEEPER_PIN P1_31 // EXP1-1 + //#define SD_DETECT_PIN P0_27 // EXP2-7 + + #define BTN_EN1 P3_26 // EXP2-5 + #define BTN_EN2 P3_25 // EXP2-3 + #define BTN_ENC P1_30 // EXP1-2 + + #define LCD_PINS_RS P0_16 // EXP1-4 + #define LCD_SDSS P0_28 // EXP2-4 + #define LCD_PINS_ENABLE P0_18 // EXP1-3 + #define LCD_PINS_D4 P0_15 // EXP1-5 + + #define KILL_PIN P2_11 // EXP2-10 + #endif // ULTRA_LCD +// +// SD Support +// +#if NONE(LPC_SD_LCD, LPC_SD_ONBOARD, LPC_SD_CUSTOM_CABLE) + #undef USB_SD_DISABLED + #define USB_SD_ONBOARD + #define LPC_SD_ONBOARD +#endif + +#if ENABLED(LPC_SD_LCD) + + #define SCK_PIN P0_07 // (52) system defined J3-9 & AUX-3 + #define MISO_PIN P0_08 // (50) system defined J3-10 & AUX-3 + #define MOSI_PIN P0_09 // (51) system defined J3-10 & AUX-3 + #define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin + #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card + +#elif ENABLED(LPC_SD_ONBOARD) + + #if ENABLED(USB_SD_ONBOARD) + // When sharing the SD card with a PC the LCD menu options are + // needed to mount/unmount and refresh SD. So disable SD detect. + #define SHARED_SD_CARD + #undef SD_DETECT_PIN // No SD detect pin for the onboard card + #endif + + #define SCK_PIN P0_07 + #define MISO_PIN P0_08 + #define MOSI_PIN P0_09 + #define SS_PIN P0_06 // Chip select for SD card used by Marlin + #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card + +#endif + // // Ethernet pins // -#define ENET_MDIO P1_17 -#define ENET_RX_ER P1_14 -#define ENET_RXD1 P1_10 -#define ENET_MOC P1_16 -#define REF_CLK P1_15 -#define ENET_RXD0 P1_09 -#define ENET_CRS P1_08 -#define ENET_TX_EN P1_04 -#define ENET_TXD0 P1_00 -#define ENET_TXD1 P1_01 +//#define ENET_MDIO P1_17 // Ethernet pin 5 (bottom, 3 from left) +//#define ENET_RX_ER P1_14 +//#define ENET_RXD1 P1_10 // Ethernet pin 10 (top row, 5 from left) +//#define ENET_MOC P1_16 // Ethernet pin 6 (top row, 3 from left) +//#define REF_CLK P1_15 +//#define ENET_RXD0 P1_09 // Ethernet pin 9 (bottom, 5 from left) +//#define ENET_CRS P1_08 // Ethernet pin 8 (top row, 4 from left) - INPUT ONLY +//#define ENET_TX_EN P1_04 // Ethernet pin 11 (bottom, 6 from left) +//#define ENET_TXD0 P1_00 // Ethernet pin 12 (top row, 6 from left) +//#define ENET_TXD1 P1_01 // Ethernet pin 13 (bottom, 7 from left) + +/** + * EXP1 pins + * 1 - P1_31 + * 2 - P1_30 + * 3 - P0_18 + * 4 - P0_16 + * 5 - P0_15 + * 6 - N/C + * 7 - N/C + * 8 - P0_27 (also on EXP2-7) + * 9 - GND + * 10 - +5V + * + * + * EXP2 pins + * 1 - P0_08 + * 2 - P0_07 + * 3 - P3_26 + * 4 - P0_28 + * 5 - P3_25 + * 6 - P0_09 + * 7 - P0_27 (also on EXP1_8) + * 8 - P2_11 + * 9 - GND + * 10 - N/C + */