Configurator is out-of-date AGAIN (PR#2550)

This commit is contained in:
Richard Wackerbarth 2015-07-30 09:29:43 -05:00
parent 67c4d22984
commit 525d0dc239
2 changed files with 18 additions and 3 deletions

View File

@ -305,10 +305,10 @@ Here are some standard links for getting your machine calibrated:
// @section machine // @section machine
// Uncomment this option to enable CoreXY kinematics // Uncomment this option to enable CoreXY kinematics
// #define COREXY //#define COREXY
// Uncomment this option to enable CoreXZ kinematics // Uncomment this option to enable CoreXZ kinematics
// #define COREXZ //#define COREXZ
// Enable this option for Toshiba steppers // Enable this option for Toshiba steppers
//#define CONFIG_STEPPERS_TOSHIBA //#define CONFIG_STEPPERS_TOSHIBA
@ -612,6 +612,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define EEPROM_CHITCHAT // Please keep turned on if you can. #define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif #endif
//
// M100 Free Memory Watcher
//
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
// @section temperature // @section temperature
// Preheat Constants // Preheat Constants

View File

@ -94,6 +94,11 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// This defines the minimal speed for the main fan, run in PWM mode
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
//#define FAN_MIN_PWM 50
// @section extruder // @section extruder
// Extruder cooling fans // Extruder cooling fans
@ -290,7 +295,9 @@
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should // in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise // be commented out otherwise
#define SDCARDDETECTINVERTED #ifndef ELB_FULL_GRAPHIC_CONTROLLER
#define SDCARDDETECTINVERTED
#endif
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
@ -448,6 +455,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
#define FILAMENTCHANGE_ZADD 10 #define FILAMENTCHANGE_ZADD 10
#define FILAMENTCHANGE_FIRSTRETRACT -2 #define FILAMENTCHANGE_FIRSTRETRACT -2
#define FILAMENTCHANGE_FINALRETRACT -100 #define FILAMENTCHANGE_FINALRETRACT -100
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
#endif #endif
#endif #endif