Fixed AUTOTEMP (M109 S215 B260 F1 starts autotemp)
Changed SLOWDOWN. IF this does not work ok OLD_SLOWDOWN is the old algo.
This commit is contained in:
parent
8aee9d51b6
commit
67cf105bc6
@ -121,7 +121,7 @@
|
||||
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
||||
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
||||
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
@ -196,7 +196,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
//#define ULTRA_LCD //general lcd support, also 16x2
|
||||
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
|
||||
//#define ULTIPANEL
|
||||
#define ULTIPANEL
|
||||
#ifdef ULTIPANEL
|
||||
// #define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define SDSUPPORT
|
||||
|
@ -41,8 +41,8 @@
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
|
||||
//#define AUTOTEMP
|
||||
// on an ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
#define AUTOTEMP
|
||||
#ifdef AUTOTEMP
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
@ -94,8 +94,8 @@
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
@ -147,9 +147,6 @@
|
||||
|
||||
#endif // ADVANCE
|
||||
|
||||
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
|
||||
//#define DEBUG_STEPS
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
@ -64,6 +64,7 @@
|
||||
|
||||
|
||||
#define SERIAL_PROTOCOL(x) MYSERIAL.print(x);
|
||||
#define SERIAL_PROTOCOL_F(x,y) MYSERIAL.print(x,y);
|
||||
#define SERIAL_PROTOCOLPGM(x) serialprintPGM(MYPGM(x));
|
||||
#define SERIAL_PROTOCOLLN(x) {MYSERIAL.print(x);MYSERIAL.write('\n');}
|
||||
#define SERIAL_PROTOCOLLNPGM(x) {serialprintPGM(MYPGM(x));MYSERIAL.write('\n');}
|
||||
|
@ -849,14 +849,14 @@ void process_commands()
|
||||
}
|
||||
#if (TEMP_0_PIN > -1)
|
||||
SERIAL_PROTOCOLPGM("ok T:");
|
||||
SERIAL_PROTOCOL(degHotend(tmp_extruder));
|
||||
//SERIAL_PROTOCOLPGM("/");
|
||||
//SERIAL_PROTOCOL(degTargetHotend(tmp_extruder));
|
||||
SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1);
|
||||
SERIAL_PROTOCOLPGM(" /");
|
||||
SERIAL_PROTOCOL_F(degTargetHotend(tmp_extruder),1);
|
||||
#if TEMP_BED_PIN > -1
|
||||
SERIAL_PROTOCOLPGM(" B:");
|
||||
SERIAL_PROTOCOL(degBed());
|
||||
//SERIAL_PROTOCOLPGM("/");
|
||||
//SERIAL_PROTOCOL(degTargetBed());
|
||||
SERIAL_PROTOCOL_F(degBed(),1);
|
||||
SERIAL_PROTOCOLPGM(" /");
|
||||
SERIAL_PROTOCOL_F(degTargetBed(),1);
|
||||
#endif //TEMP_BED_PIN
|
||||
#else
|
||||
SERIAL_ERROR_START;
|
||||
@ -888,7 +888,7 @@ void process_commands()
|
||||
if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder);
|
||||
#ifdef AUTOTEMP
|
||||
if (code_seen('S')) autotemp_min=code_value();
|
||||
if (code_seen('G')) autotemp_max=code_value();
|
||||
if (code_seen('B')) autotemp_max=code_value();
|
||||
if (code_seen('F'))
|
||||
{
|
||||
autotemp_factor=code_value();
|
||||
@ -915,7 +915,7 @@ void process_commands()
|
||||
if( (millis() - codenum) > 1000UL )
|
||||
{ //Print Temp Reading and remaining time every 1 second while heating up/cooling down
|
||||
SERIAL_PROTOCOLPGM("T:");
|
||||
SERIAL_PROTOCOL( degHotend(tmp_extruder) );
|
||||
SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1);
|
||||
SERIAL_PROTOCOLPGM(" E:");
|
||||
SERIAL_PROTOCOL((int)tmp_extruder);
|
||||
#ifdef TEMP_RESIDENCY_TIME
|
||||
@ -968,7 +968,8 @@ void process_commands()
|
||||
SERIAL_PROTOCOLPGM(" E:");
|
||||
SERIAL_PROTOCOL((int)active_extruder);
|
||||
SERIAL_PROTOCOLPGM(" B:");
|
||||
SERIAL_PROTOCOLLN(degBed());
|
||||
SERIAL_PROTOCOL_F(degBed(),1);
|
||||
SERIAL_PROTOCOLLN("");
|
||||
codenum = millis();
|
||||
}
|
||||
manage_heater();
|
||||
@ -1058,8 +1059,21 @@ void process_commands()
|
||||
for(int8_t i=0; i < NUM_AXIS; i++)
|
||||
{
|
||||
if(code_seen(axis_codes[i]))
|
||||
|
||||
if(i == 3) { // E
|
||||
float value = code_value();
|
||||
if(value < 20.0) {
|
||||
float factor = axis_steps_per_unit[i] / value; // increase e constants if M92 E14 is given for netfab.
|
||||
max_e_jerk *= factor;
|
||||
max_feedrate[i] *= factor;
|
||||
axis_steps_per_sqr_second[i] *= factor;
|
||||
}
|
||||
axis_steps_per_unit[i] = value;
|
||||
}
|
||||
else {
|
||||
axis_steps_per_unit[i] = code_value();
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 115: // M115
|
||||
SerialprintPGM(MSG_M115_REPORT);
|
||||
|
@ -51,9 +51,6 @@
|
||||
IntersectionDistance[s1_, s2_, a_, d_] := (2 a d - s1^2 + s2^2)/(4 a)
|
||||
*/
|
||||
|
||||
|
||||
|
||||
|
||||
#include "Marlin.h"
|
||||
#include "planner.h"
|
||||
#include "stepper.h"
|
||||
@ -377,21 +374,27 @@ void plan_init() {
|
||||
void getHighESpeed()
|
||||
{
|
||||
static float oldt=0;
|
||||
if(!autotemp_enabled)
|
||||
if(!autotemp_enabled){
|
||||
return;
|
||||
if(degTargetHotend0()+2<autotemp_min) //probably temperature set to zero.
|
||||
}
|
||||
if(degTargetHotend0()+2<autotemp_min) { //probably temperature set to zero.
|
||||
return; //do nothing
|
||||
}
|
||||
|
||||
float high=0;
|
||||
float high=0.0;
|
||||
uint8_t block_index = block_buffer_tail;
|
||||
|
||||
while(block_index != block_buffer_head) {
|
||||
float se=block_buffer[block_index].steps_e/float(block_buffer[block_index].step_event_count)*block_buffer[block_index].nominal_rate;
|
||||
//se; units steps/sec;
|
||||
if((block_buffer[block_index].steps_x != 0) ||
|
||||
(block_buffer[block_index].steps_y != 0) ||
|
||||
(block_buffer[block_index].steps_z != 0)) {
|
||||
float se=(float(block_buffer[block_index].steps_e)/float(block_buffer[block_index].step_event_count))*block_buffer[block_index].nominal_speed;
|
||||
//se; mm/sec;
|
||||
if(se>high)
|
||||
{
|
||||
high=se;
|
||||
}
|
||||
}
|
||||
block_index = (block_index+1) & (BLOCK_BUFFER_SIZE - 1);
|
||||
}
|
||||
|
||||
@ -407,10 +410,6 @@ void getHighESpeed()
|
||||
}
|
||||
oldt=t;
|
||||
setTargetHotend0(t);
|
||||
// SERIAL_ECHO_START;
|
||||
// SERIAL_ECHOPAIR("highe",high);
|
||||
// SERIAL_ECHOPAIR(" t",t);
|
||||
// SERIAL_ECHOLN("");
|
||||
}
|
||||
#endif
|
||||
|
||||
@ -456,6 +455,9 @@ void check_axes_activity() {
|
||||
analogWrite(FAN_PIN,tail_fan_speed);
|
||||
}
|
||||
#endif
|
||||
#ifdef AUTOTEMP
|
||||
getHighESpeed();
|
||||
#endif
|
||||
}
|
||||
|
||||
|
||||
@ -540,7 +542,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
// Enable all
|
||||
if(block->steps_e != 0) { enable_e0();enable_e1();enable_e2(); }
|
||||
|
||||
|
||||
if (block->steps_e == 0) {
|
||||
if(feed_rate<mintravelfeedrate) feed_rate=mintravelfeedrate;
|
||||
}
|
||||
@ -548,12 +549,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
if(feed_rate<minimumfeedrate) feed_rate=minimumfeedrate;
|
||||
}
|
||||
|
||||
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
|
||||
int moves_queued=(block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1);
|
||||
#ifdef SLOWDOWN
|
||||
if(moves_queued < (BLOCK_BUFFER_SIZE * 0.5) && moves_queued > 1) feed_rate = feed_rate*moves_queued / (BLOCK_BUFFER_SIZE * 0.5);
|
||||
#endif
|
||||
|
||||
float delta_mm[4];
|
||||
delta_mm[X_AXIS] = (target[X_AXIS]-position[X_AXIS])/axis_steps_per_unit[X_AXIS];
|
||||
delta_mm[Y_AXIS] = (target[Y_AXIS]-position[Y_AXIS])/axis_steps_per_unit[Y_AXIS];
|
||||
@ -569,34 +564,33 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
// Calculate speed in mm/second for each axis. No divide by zero due to previous checks.
|
||||
float inverse_second = feed_rate * inverse_millimeters;
|
||||
|
||||
int moves_queued=(block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1);
|
||||
|
||||
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
|
||||
#ifdef OLD_SLOWDOWN
|
||||
if(moves_queued < (BLOCK_BUFFER_SIZE * 0.5) && moves_queued > 1) feed_rate = feed_rate*moves_queued / (BLOCK_BUFFER_SIZE * 0.5);
|
||||
#endif
|
||||
|
||||
#ifdef SLOWDOWN
|
||||
// segment time im micro seconds
|
||||
unsigned long segment_time = lround(1000000.0/inverse_second);
|
||||
if ((moves_queued > 1) && (moves_queued < (BLOCK_BUFFER_SIZE * 0.5))) {
|
||||
if (segment_time < minsegmenttime) { // buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
|
||||
inverse_second=1000000.0/(segment_time+lround(2*(minsegmenttime-segment_time)/moves_queued));
|
||||
}
|
||||
}
|
||||
#endif
|
||||
// END OF SLOW DOWN SECTION
|
||||
|
||||
|
||||
block->nominal_speed = block->millimeters * inverse_second; // (mm/sec) Always > 0
|
||||
block->nominal_rate = ceil(block->step_event_count * inverse_second); // (step/sec) Always > 0
|
||||
|
||||
|
||||
/*
|
||||
// segment time im micro seconds
|
||||
long segment_time = lround(1000000.0/inverse_second);
|
||||
if ((blockcount>0) && (blockcount < (BLOCK_BUFFER_SIZE - 4))) {
|
||||
if (segment_time<minsegmenttime) { // buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
|
||||
segment_time=segment_time+lround(2*(minsegmenttime-segment_time)/blockcount);
|
||||
}
|
||||
}
|
||||
else {
|
||||
if (segment_time<minsegmenttime) segment_time=minsegmenttime;
|
||||
}
|
||||
// END OF SLOW DOWN SECTION
|
||||
*/
|
||||
|
||||
|
||||
// Calculate speed in mm/sec for each axis
|
||||
// Calculate and limit speed in mm/sec for each axis
|
||||
float current_speed[4];
|
||||
for(int i=0; i < 4; i++) {
|
||||
current_speed[i] = delta_mm[i] * inverse_second;
|
||||
}
|
||||
|
||||
// Limit speed per axis
|
||||
float speed_factor = 1.0; //factor <=1 do decrease speed
|
||||
for(int i=0; i < 4; i++) {
|
||||
current_speed[i] = delta_mm[i] * inverse_second;
|
||||
if(abs(current_speed[i]) > max_feedrate[i])
|
||||
speed_factor = min(speed_factor, max_feedrate[i] / abs(current_speed[i]));
|
||||
}
|
||||
@ -633,17 +627,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
|
||||
// Correct the speed
|
||||
if( speed_factor < 1.0) {
|
||||
// Serial.print("speed factor : "); Serial.println(speed_factor);
|
||||
for(int i=0; i < 4; i++) {
|
||||
if(abs(current_speed[i]) > max_feedrate[i])
|
||||
speed_factor = min(speed_factor, max_feedrate[i] / abs(current_speed[i]));
|
||||
/*
|
||||
if(speed_factor < 0.1) {
|
||||
Serial.print("speed factor : "); Serial.println(speed_factor);
|
||||
Serial.print("current_speed"); Serial.print(i); Serial.print(" : "); Serial.println(current_speed[i]);
|
||||
}
|
||||
*/
|
||||
}
|
||||
for(unsigned char i=0; i < 4; i++) {
|
||||
current_speed[i] *= speed_factor;
|
||||
}
|
||||
@ -784,9 +767,6 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
*/
|
||||
#endif // ADVANCE
|
||||
|
||||
|
||||
|
||||
|
||||
calculate_trapezoid_for_block(block, block->entry_speed/block->nominal_speed,
|
||||
MINIMUM_PLANNER_SPEED/block->nominal_speed);
|
||||
|
||||
@ -797,9 +777,7 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
|
||||
memcpy(position, target, sizeof(target)); // position[] = target[]
|
||||
|
||||
planner_recalculate();
|
||||
#ifdef AUTOTEMP
|
||||
getHighESpeed();
|
||||
#endif
|
||||
|
||||
st_wake_up();
|
||||
}
|
||||
|
||||
|
@ -54,7 +54,6 @@ volatile static unsigned long step_events_completed; // The number of step event
|
||||
static long old_advance = 0;
|
||||
#endif
|
||||
static long e_steps[3];
|
||||
static unsigned char busy = false; // TRUE when SIG_OUTPUT_COMPARE1A is being serviced. Used to avoid retriggering that handler.
|
||||
static long acceleration_time, deceleration_time;
|
||||
//static unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate;
|
||||
static unsigned short acc_step_rate; // needed for deccelaration start point
|
||||
@ -216,7 +215,6 @@ void enable_endstops(bool check)
|
||||
|
||||
void st_wake_up() {
|
||||
// TCNT1 = 0;
|
||||
if(busy == false)
|
||||
ENABLE_STEPPER_DRIVER_INTERRUPT();
|
||||
}
|
||||
|
||||
@ -295,6 +293,7 @@ ISR(TIMER1_COMPA_vect)
|
||||
// Anything in the buffer?
|
||||
current_block = plan_get_current_block();
|
||||
if (current_block != NULL) {
|
||||
current_block->busy = true;
|
||||
trapezoid_generator_reset();
|
||||
counter_x = -(current_block->step_event_count >> 1);
|
||||
counter_y = counter_x;
|
||||
@ -773,12 +772,7 @@ void st_init()
|
||||
TIMSK0 |= (1<<OCIE0A);
|
||||
#endif //ADVANCE
|
||||
|
||||
#ifdef ENDSTOPS_ONLY_FOR_HOMING
|
||||
enable_endstops(false);
|
||||
#else
|
||||
enable_endstops(true);
|
||||
#endif
|
||||
|
||||
enable_endstops(true); // Start with endstops active. After homing they can be disabled
|
||||
sei();
|
||||
}
|
||||
|
||||
|
@ -95,17 +95,6 @@ static unsigned long previous_millis_bed_heater;
|
||||
static int maxttemp[EXTRUDERS] = { 16383 }; // the first value used for all
|
||||
static int bed_minttemp = 0;
|
||||
static int bed_maxttemp = 16383;
|
||||
static int heater_pin_map[EXTRUDERS] = { HEATER_0_PIN
|
||||
#if EXTRUDERS > 1
|
||||
, HEATER_1_PIN
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
, HEATER_2_PIN
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
#error Unsupported number of extruders
|
||||
#endif
|
||||
};
|
||||
static void *heater_ttbl_map[EXTRUDERS] = { (void *)heater_0_temptable
|
||||
#if EXTRUDERS > 1
|
||||
, (void *)heater_1_temptable
|
||||
@ -138,7 +127,6 @@ void PID_autotune(float temp)
|
||||
float input;
|
||||
int cycles=0;
|
||||
bool heating = true;
|
||||
soft_pwm[0] = 255>>1;
|
||||
|
||||
unsigned long temp_millis = millis();
|
||||
unsigned long t1=temp_millis;
|
||||
@ -154,7 +142,9 @@ void PID_autotune(float temp)
|
||||
|
||||
SERIAL_ECHOLN("PID Autotune start");
|
||||
|
||||
//disable_heater(); // switch off all heaters.
|
||||
disable_heater(); // switch off all heaters.
|
||||
|
||||
soft_pwm[0] = 255>>1;
|
||||
|
||||
for(;;) {
|
||||
|
||||
@ -202,6 +192,7 @@ void PID_autotune(float temp)
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd);
|
||||
/*
|
||||
Kp = 0.33*Ku;
|
||||
Ki = Kp/Tu;
|
||||
Kd = Kp*Tu/3;
|
||||
@ -216,6 +207,7 @@ void PID_autotune(float temp)
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd);
|
||||
*/
|
||||
}
|
||||
}
|
||||
soft_pwm[0] = (bias + d) >> 1;
|
||||
@ -225,7 +217,7 @@ void PID_autotune(float temp)
|
||||
}
|
||||
}
|
||||
if(input > (temp + 20)) {
|
||||
SERIAL_PROTOCOLLNPGM("PID Autotune failed !, Temperature to high");
|
||||
SERIAL_PROTOCOLLNPGM("PID Autotune failed! Temperature to high");
|
||||
return;
|
||||
}
|
||||
if(millis() - temp_millis > 2000) {
|
||||
@ -235,6 +227,14 @@ void PID_autotune(float temp)
|
||||
SERIAL_PROTOCOLPGM(" @:");
|
||||
SERIAL_PROTOCOLLN(getHeaterPower(0));
|
||||
}
|
||||
if(((millis() - t1) + (millis() - t2)) > (10L*60L*1000L*2L)) {
|
||||
SERIAL_PROTOCOLLNPGM("PID Autotune failed! timeout");
|
||||
return;
|
||||
}
|
||||
if(cycles > 5) {
|
||||
SERIAL_PROTOCOLLNPGM("PID Autotune finished ! Place the Kp, Ki and Kd constants in the configuration.h");
|
||||
return;
|
||||
}
|
||||
LCD_STATUS;
|
||||
}
|
||||
}
|
||||
@ -313,11 +313,9 @@ void manage_heater()
|
||||
// Check if temperature is within the correct range
|
||||
if((current_raw[e] > minttemp[e]) && (current_raw[e] < maxttemp[e]))
|
||||
{
|
||||
//analogWrite(heater_pin_map[e], pid_output);
|
||||
soft_pwm[e] = (int)pid_output >> 1;
|
||||
}
|
||||
else {
|
||||
//analogWrite(heater_pin_map[e], 0);
|
||||
soft_pwm[e] = 0;
|
||||
}
|
||||
} // End extruder for loop
|
||||
@ -680,7 +678,7 @@ void disable_heater()
|
||||
target_raw[0]=0;
|
||||
soft_pwm[0]=0;
|
||||
#if HEATER_0_PIN > -1
|
||||
digitalWrite(HEATER_0_PIN,LOW);
|
||||
WRITE(HEATER_0_PIN,LOW);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@ -688,7 +686,7 @@ void disable_heater()
|
||||
target_raw[1]=0;
|
||||
soft_pwm[1]=0;
|
||||
#if HEATER_1_PIN > -1
|
||||
digitalWrite(HEATER_1_PIN,LOW);
|
||||
WRITE(HEATER_1_PIN,LOW);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@ -696,20 +694,20 @@ void disable_heater()
|
||||
target_raw[2]=0;
|
||||
soft_pwm[2]=0;
|
||||
#if HEATER_2_PIN > -1
|
||||
digitalWrite(HEATER_2_PIN,LOW);
|
||||
WRITE(HEATER_2_PIN,LOW);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if TEMP_BED_PIN > -1
|
||||
target_raw_bed=0;
|
||||
#if HEATER_BED_PIN > -1
|
||||
digitalWrite(HEATER_BED_PIN,LOW);
|
||||
WRITE(HEATER_BED_PIN,LOW);
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
void max_temp_error(uint8_t e) {
|
||||
digitalWrite(heater_pin_map[e], 0);
|
||||
disable_heater();
|
||||
if(IsStopped() == false) {
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLN(e);
|
||||
@ -718,7 +716,7 @@ void max_temp_error(uint8_t e) {
|
||||
}
|
||||
|
||||
void min_temp_error(uint8_t e) {
|
||||
digitalWrite(heater_pin_map[e], 0);
|
||||
disable_heater();
|
||||
if(IsStopped() == false) {
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLN(e);
|
||||
@ -727,7 +725,7 @@ void min_temp_error(uint8_t e) {
|
||||
}
|
||||
|
||||
void bed_max_temp_error(void) {
|
||||
digitalWrite(HEATER_BED_PIN, 0);
|
||||
WRITE(HEATER_BED_PIN, 0);
|
||||
if(IsStopped() == false) {
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLNPGM("Temperature heated bed switched off. MAXTEMP triggered !!");
|
||||
|
Loading…
Reference in New Issue
Block a user