Clean up trailing whitespace and tabs

This commit is contained in:
Scott Lahteine 2017-05-16 15:25:30 -05:00
parent d30e478f97
commit 6b6630e11b
7 changed files with 19 additions and 29 deletions

View File

@ -834,7 +834,7 @@
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#endif
#endif
// Shorthand
#define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))

View File

@ -922,10 +922,10 @@
// at which point movement will be level to the machine's XY plane.
// The height can be set with M420 Z<height>
//#define ENABLE_LEVELING_FADE_HEIGHT
// Set the boundaries for probing (where the probe can reach).
#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#endif
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)

View File

@ -920,10 +920,10 @@
// at which point movement will be level to the machine's XY plane.
// The height can be set with M420 Z<height>
//#define ENABLE_LEVELING_FADE_HEIGHT
// Set the boundaries for probing (where the probe can reach).
#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#endif
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)

View File

@ -926,10 +926,10 @@
// at which point movement will be level to the machine's XY plane.
// The height can be set with M420 Z<height>
//#define ENABLE_LEVELING_FADE_HEIGHT
// Set the boundaries for probing (where the probe can reach).
#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#endif
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)

View File

@ -989,10 +989,10 @@
// at which point movement will be level to the machine's XY plane.
// The height can be set with M420 Z<height>
//#define ENABLE_LEVELING_FADE_HEIGHT
// Set the boundaries for probing (where the probe can reach).
#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#endif
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)

View File

@ -322,17 +322,15 @@
// Check for commands that require the printer to be homed.
if (axis_unhomed_error()) {
if (code_seen('J'))
if (code_seen('J'))
home_all_axes();
else
if (code_seen('P')) {
int p_val;
if (code_has_value()) {
p_val = code_value_int();
if ( p_val==1 || p_val==2 || p_val==4 )
home_all_axes();
}
else if (code_seen('P')) {
if (code_has_value()) {
const int p_val = code_value_int();
if (p_val == 1 || p_val == 2 || p_val == 4)
home_all_axes();
}
}
}
if (g29_parameter_parsing()) return; // abort if parsing the simple parameters causes a problem,
@ -1341,15 +1339,7 @@
// Also for round beds, there are grid points outside the bed that nozzle can't reach.
// Prune them from the list and ignore them till the next Phase (manual nozzle probing).
// if ((probe_as_reference && position_is_reachable_by_probe_raw_xy(mx, my)) || position_is_reachable_raw_xy(mx, my))
// continue;
//
// THE ABOVE CODE IS NOT A REPLACEMENT FOR THE CODE BELOW!!!!!!!
//
bool reachable = probe_as_reference ?
position_is_reachable_by_probe_raw_xy( mx, my ) :
position_is_reachable_raw_xy( mx, my );
if ( ! reachable )
if ( ! (probe_as_reference ? position_is_reachable_by_probe_raw_xy(mx, my) : position_is_reachable_raw_xy(mx, my)) )
continue;
// Reachable. Check if it's the closest location to the nozzle.

View File

@ -632,7 +632,7 @@
z_cxyd = z_cxy1 - z_cxy0; // z height difference along cx from y0 to y1
float z_cxym = z_cxyd * (1.0 / (MESH_Y_DIST)); // z slope per y along cx from y0 to y1
// float z_cxcy = z_cxy0 + z_cxym * cy; // interpolated mesh z height along cx at cy (do inside the segment loop)
// As subsequent segments step through this cell, the z_cxy0 intercept will change
@ -649,7 +649,7 @@
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
z_cxcy *= fade_scaling_factor; // apply fade factor to interpolated mesh height
#endif
z_cxcy += ubl.state.z_offset; // add fixed mesh offset from G29 Z
if (--segments == 0) { // if this is last segment, use ltarget for exact