diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 7ea040803c..b29e1e4054 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1910,6 +1910,12 @@ // https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 // //#define FYSETC_MINI_12864 +#ifdef FYSETC_MINI_12864 + #define FYSETC_MINI_12864_REV_1_2 // types C, D, E & F back light is monochrome (always on) - discrete RGB signals + //#define FYSETC_MINI_12864_REV_2_0 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - discrete RGB signals + //#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - RGB + //#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - Neopixel +#endif // // Factory display for Creality CR-10 @@ -2013,6 +2019,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp index a1934886f9..5adc7fcf09 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp @@ -53,7 +53,7 @@ // Public functions // -------------------------------------------------------------------------- -#if ENABLED(DUE_SOFTWARE_SPI) +#if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI) // -------------------------------------------------------------------------- // software SPI @@ -739,7 +739,42 @@ #define SPI_MODE_2_DUE_HW 0 #define SPI_MODE_3_DUE_HW 1 + /** + * The DUE SPI controller is set up so the upper word of the longword + * written to the transmit data register selects which SPI Chip Select + * Register is used. This allows different streams to have different SPI + * settings. + * + * In practice it's spooky. Some combinations hang the system, while others + * upset the peripheral device. + * + * SPI mode should be the same for all streams. The FYSETC_MINI_12864 gets + * upset if the clock phase changes after chip select goes active. + * + * SPI_CSR_CSAAT should be set for all streams. If not the WHILE_TX(0) + * macro returns immediately which can result in the SPI chip select going + * inactive before all the data has been sent. + * + * The TMC2130 library uses SPI0->SPI_CSR[3]. + * + * The U8G hardware SPI uses SPI0->SPI_CSR[0]. The system hangs and/or the + * FYSETC_MINI_12864 gets upset if lower baud rates are used and the SD card + * is inserted or removed. + * + * The SD card uses SPI0->SPI_CSR[3]. Efforts were made to use [1] and [2] + * but they all resulted in hangs or garbage on the LCD. + * + * The SPI controlled chip selects are NOT enabled in the GPIO controller. + * The application must control the chip select. + * + * All of the above can be avoided by defining FORCE_SOFT_SPI to force the + * display to use software SPI. + * + */ + void spiInit(uint8_t spiRate=6) { // Default to slowest rate if not specified) + // Also sets U8G SPI rate to 4MHz and the SPI mode to 3 + // 8.4 MHz, 4 MHz, 2 MHz, 1 MHz, 0.5 MHz, 0.329 MHz, 0.329 MHz constexpr int spiDivider[] = { 10, 21, 42, 84, 168, 255, 255 }; if (spiRate > 6) spiRate = 1; @@ -760,15 +795,16 @@ // TMC2103 compatible setup // Master mode, no fault detection, PCS bits in data written to TDR select CSR register SPI0->SPI_MR = SPI_MR_MSTR | SPI_MR_PS | SPI_MR_MODFDIS; - // SPI mode 0, 8 Bit data transfer, baud rate - SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_0_DUE_HW; // use same CSR as TMC2130 + // SPI mode 3, 8 Bit data transfer, baud rate + SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // use same CSR as TMC2130 + SPI0->SPI_CSR[0] = SPI_CSR_SCBR(spiDivider[1]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // U8G default to 4MHz } void spiBegin() { spiInit(); } static uint8_t spiTransfer(uint8_t data) { WHILE_TX(0); - SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte + SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte (use SPI0->SPI_CSR[3]) WHILE_TX(0); WHILE_RX(0); return SPI0->SPI_RDR; diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp index 1546407a1e..3cef880bca 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp +++ b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp @@ -99,7 +99,7 @@ static void u8g_com_DUE_st7920_write_byte_sw_spi(uint8_t rs, uint8_t val) { spiSend_sw_DUE(rs ? 0x0FA : 0x0F8); // Command or Data DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe } - spiSend_sw_DUE(val & 0x0F0); + spiSend_sw_DUE(val & 0xF0); spiSend_sw_DUE(val << 4); } @@ -168,6 +168,42 @@ uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va return 1; } -#endif // HAS_GRAPHICAL_LCD +#if ENABLED(LIGHTWEIGHT_UI) + #include "../../lcd/ultralcd.h" + #include "../shared/HAL_ST7920.h" + #define ST7920_CS_PIN LCD_PINS_RS + + #if DOGM_SPI_DELAY_US > 0 + #define U8G_DELAY() DELAY_US(DOGM_SPI_DELAY_US) + #else + #define U8G_DELAY() DELAY_US(10) + #endif + + void ST7920_cs() { + WRITE(ST7920_CS_PIN, HIGH); + U8G_DELAY(); + } + + void ST7920_ncs() { + WRITE(ST7920_CS_PIN, LOW); + } + + void ST7920_set_cmd() { + spiSend_sw_DUE(0xF8); + DELAY_US(40); + } + + void ST7920_set_dat() { + spiSend_sw_DUE(0xFA); + DELAY_US(40); + } + + void ST7920_write_byte(const uint8_t val) { + spiSend_sw_DUE(val & 0xF0); + spiSend_sw_DUE(val << 4); + } +#endif // LIGHTWEIGHT_UI + +#endif // HAS_GRAPHICAL_LCD #endif // ARDUINO_ARCH_SAM diff --git a/Marlin/src/HAL/HAL_ESP32/HAL.cpp b/Marlin/src/HAL/HAL_ESP32/HAL.cpp index c755eb6056..53966de55e 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL.cpp +++ b/Marlin/src/HAL/HAL_ESP32/HAL.cpp @@ -133,12 +133,16 @@ int freeMemory() { // -------------------------------------------------------------------------- // ADC // -------------------------------------------------------------------------- -#define ADC1_CHANNEL(pin) ADC1_GPIO##pin_CHANNEL +#define ADC1_CHANNEL(pin) ADC1_GPIO ## pin ## _CHANNEL adc1_channel_t get_channel(int pin) { switch (pin) { - case 36: return ADC1_GPIO36_CHANNEL; - case 39: return ADC1_GPIO39_CHANNEL; + case 39: return ADC1_CHANNEL(39); + case 36: return ADC1_CHANNEL(36); + case 35: return ADC1_CHANNEL(35); + case 34: return ADC1_CHANNEL(34); + case 33: return ADC1_CHANNEL(33); + case 32: return ADC1_CHANNEL(32); } return ADC1_CHANNEL_MAX; @@ -147,8 +151,15 @@ adc1_channel_t get_channel(int pin) { void HAL_adc_init() { // Configure ADC adc1_config_width(ADC_WIDTH_12Bit); - adc1_config_channel_atten(get_channel(36), ADC_ATTEN_11db); adc1_config_channel_atten(get_channel(39), ADC_ATTEN_11db); + adc1_config_channel_atten(get_channel(36), ADC_ATTEN_11db); + adc1_config_channel_atten(get_channel(35), ADC_ATTEN_11db); + adc1_config_channel_atten(get_channel(34), ADC_ATTEN_11db); + adc1_config_channel_atten(get_channel(33), ADC_ATTEN_11db); + adc1_config_channel_atten(get_channel(32), ADC_ATTEN_11db); + + // Note that adc2 is shared with the WiFi module, which has higher priority, so the conversion may fail. + // That's why we're not setting it up here. // Calculate ADC characteristics i.e. gain and offset factors esp_adc_cal_characterize(ADC_UNIT_1, ADC_ATTEN_DB_11, ADC_WIDTH_BIT_12, V_REF, &characteristics); diff --git a/Marlin/src/HAL/HAL_ESP32/HAL.h b/Marlin/src/HAL/HAL_ESP32/HAL.h index 3285a8b2b9..16859263b2 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL.h +++ b/Marlin/src/HAL/HAL_ESP32/HAL.h @@ -30,13 +30,18 @@ #include +// these are going to be re-defined in Arduino.h #undef DISABLED #undef M_PI +#undef _BV #include +// revert back to the correct (old) definition #undef DISABLED #define DISABLED(V...) DO(DIS,&&,V) +// re-define in case Arduino.h has been skipped due to earlier inclusion (i.e. in Marlin\src\HAL\HAL_ESP32\i2s.cpp) +#define _BV(b) (1UL << (b)) #include "../shared/math_32bit.h" #include "../shared/HAL_SPI.h" diff --git a/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h b/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h index dc2cd708de..b71ca78418 100644 --- a/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h +++ b/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h @@ -27,6 +27,10 @@ * Utility functions */ +// I2S expander pin mapping. +#define IS_I2S_EXPANDER_PIN(IO) TEST(IO, 7) +#define I2S_EXPANDER_PIN_INDEX(IO) (IO & 0x7F) + // Set pin as input #define _SET_INPUT(IO) pinMode(IO, INPUT) @@ -37,10 +41,10 @@ #define _PULLUP(IO, v) pinMode(IO, v ? INPUT_PULLUP : INPUT) // Read a pin wrapper -#define READ(IO) digitalRead(IO) +#define READ(IO) (IS_I2S_EXPANDER_PIN(IO) ? i2s_state(I2S_EXPANDER_PIN_INDEX(IO)) : digitalRead(IO)) // Write to a pin wrapper -#define WRITE(IO, v) (TEST(IO, 7) ? i2s_write(IO & 0x7F, v) : digitalWrite(IO, v)) +#define WRITE(IO, v) (IS_I2S_EXPANDER_PIN(IO) ? i2s_write(I2S_EXPANDER_PIN_INDEX(IO), v) : digitalWrite(IO, v)) // Set pin as input wrapper #define SET_INPUT(IO) _SET_INPUT(IO) @@ -61,8 +65,9 @@ #define extDigitalRead(IO) digitalRead(IO) #define extDigitalWrite(IO,V) digitalWrite(IO,V) -#define PWM_PIN(P) true -#define USEABLE_HARDWARE_PWM(P) PWM_PIN(P) +// PWM outputs +#define PWM_PIN(P) (P < 34) // NOTE Pins >= 34 are input only on ESP32, so they can't be used for output. +#define USEABLE_HARDWARE_PWM(P) (!IS_I2S_EXPANDER_PIN(P) && PWM_PIN(P)) // Toggle pin value #define TOGGLE(IO) WRITE(IO, !READ(IO)) diff --git a/Marlin/src/HAL/HAL_ESP32/i2s.cpp b/Marlin/src/HAL/HAL_ESP32/i2s.cpp index 42e65eacd7..0345889e07 100644 --- a/Marlin/src/HAL/HAL_ESP32/i2s.cpp +++ b/Marlin/src/HAL/HAL_ESP32/i2s.cpp @@ -21,7 +21,12 @@ */ #ifdef ARDUINO_ARCH_ESP32 -#include // replace that with the proper imports +// replace that with the proper imports, then cleanup workarounds in Marlin\src\HAL\HAL_ESP32\HAL.h +#include +// revert back to the correct definition +#undef DISABLED +#define DISABLED(V...) DO(DIS,&&,V) + #include "i2s.h" #include "../../core/macros.h" #include "driver/periph_ctrl.h" @@ -315,6 +320,10 @@ void i2s_write(uint8_t pin, uint8_t val) { SET_BIT_TO(i2s_port_data, pin, val); } +uint8_t i2s_state(uint8_t pin) { + return TEST(i2s_port_data, pin); +} + void i2s_push_sample() { dma.current[dma.rw_pos++] = i2s_port_data; } diff --git a/Marlin/src/HAL/HAL_ESP32/i2s.h b/Marlin/src/HAL/HAL_ESP32/i2s.h index 337d91b203..fbe7b2419a 100644 --- a/Marlin/src/HAL/HAL_ESP32/i2s.h +++ b/Marlin/src/HAL/HAL_ESP32/i2s.h @@ -26,6 +26,8 @@ extern uint32_t i2s_port_data; int i2s_init(); +uint8_t i2s_state(uint8_t pin); + void i2s_write(uint8_t pin, uint8_t val); void i2s_push_sample(); diff --git a/Marlin/src/HAL/HAL_ESP32/spi_pins.h b/Marlin/src/HAL/HAL_ESP32/spi_pins.h index 896d9fa853..4ef6d14ec3 100644 --- a/Marlin/src/HAL/HAL_ESP32/spi_pins.h +++ b/Marlin/src/HAL/HAL_ESP32/spi_pins.h @@ -18,7 +18,7 @@ */ #pragma once -#define SS_PIN 5 +#define SS_PIN SDSS #define SCK_PIN 18 #define MISO_PIN 19 #define MOSI_PIN 23 diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL.h b/Marlin/src/HAL/HAL_LPC1768/HAL.h index 0ac6db167e..12d73c6713 100644 --- a/Marlin/src/HAL/HAL_LPC1768/HAL.h +++ b/Marlin/src/HAL/HAL_LPC1768/HAL.h @@ -147,6 +147,9 @@ using FilteredADC = LPC176x::ADC; #define HAL_READ_ADC() FilteredADC::get_result() #define HAL_ADC_READY() FilteredADC::finished_conversion() +// A grace period for the ADC readings to stabilize before they start causing thermal protection errors. +#define THERMAL_PROTECTION_GRACE_PERIOD 500 + // Parse a G-code word into a pin index int16_t PARSED_PIN_INDEX(const char code, const int16_t dval); // P0.6 thru P0.9 are for the onboard SD card diff --git a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h b/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h index ecf0eb0c07..2338b34ee3 100644 --- a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h +++ b/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h @@ -66,12 +66,7 @@ #endif #endif // SPINDLE_LASER_ENABLE -#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && HAS_DRIVER(TMC2130) && DISABLED(TMC_USE_SW_SPI) \ - && (MB(RAMPS_14_RE_ARM_EFB) \ - || MB(RAMPS_14_RE_ARM_EEB) \ - || MB(RAMPS_14_RE_ARM_EFF) \ - || MB(RAMPS_14_RE_ARM_EEF) \ - || MB(RAMPS_14_RE_ARM_SF)) +#if IS_RE_ARM_BOARD && ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && HAS_DRIVER(TMC2130) && DISABLED(TMC_USE_SW_SPI) #error "Re-ARM with REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER and TMC2130 require TMC_USE_SW_SPI" #endif diff --git a/Marlin/src/HAL/shared/HAL_ST7920.h b/Marlin/src/HAL/shared/HAL_ST7920.h new file mode 100644 index 0000000000..9af1286c7a --- /dev/null +++ b/Marlin/src/HAL/shared/HAL_ST7920.h @@ -0,0 +1,36 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * HAL/HAL_ST7920.h + * For the HALs that provide direct access to the ST7920 display + * (bypassing U8G), it will allow the LIGHTWEIGHT_UI to operate. + */ + +#if HAS_GRAPHICAL_LCD && ENABLED(LIGHTWEIGHT_UI) + void ST7920_cs(); + void ST7920_ncs(); + void ST7920_set_cmd(); + void ST7920_set_dat(); + void ST7920_write_byte(const uint8_t data); +#endif \ No newline at end of file diff --git a/Marlin/src/core/debug_out.h b/Marlin/src/core/debug_out.h index 81e1e216b4..c43c928a29 100644 --- a/Marlin/src/core/debug_out.h +++ b/Marlin/src/core/debug_out.h @@ -26,6 +26,7 @@ // (or not) in a given .cpp file // +#undef DEBUG_PRINT_P #undef DEBUG_ECHO_START #undef DEBUG_ERROR_START #undef DEBUG_CHAR diff --git a/Marlin/src/core/language.h b/Marlin/src/core/language.h index 0dfd54b3af..14dcf8bd30 100644 --- a/Marlin/src/core/language.h +++ b/Marlin/src/core/language.h @@ -344,7 +344,6 @@ #define MSG_LCD_N3 " 4" #define MSG_LCD_N4 " 5" #define MSG_LCD_N5 " 6" -#define MSG_E0 "E0" #define MSG_E1 "E1" #define MSG_E2 "E2" #define MSG_E3 "E3" diff --git a/Marlin/src/gcode/calibrate/G34_M422.cpp b/Marlin/src/gcode/calibrate/G34_M422.cpp index 9a26400a97..36550a7bd7 100644 --- a/Marlin/src/gcode/calibrate/G34_M422.cpp +++ b/Marlin/src/gcode/calibrate/G34_M422.cpp @@ -126,6 +126,12 @@ void GcodeSuite::G34() { extruder_duplication_enabled = false; #endif + // Before moving other axes raise Z, if needed. Never lower Z. + if (current_position[Z_AXIS] < Z_CLEARANCE_BETWEEN_PROBES) { + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Raise Z (before moving to probe pos) to ", Z_CLEARANCE_BETWEEN_PROBES); + do_blocking_move_to_z(Z_CLEARANCE_BETWEEN_PROBES); + } + // Remember corrections to determine errors on each iteration float last_z_align_move[Z_STEPPER_COUNT] = ARRAY_N(Z_STEPPER_COUNT, 10000.0f, 10000.0f, 10000.0f), z_measured[Z_STEPPER_COUNT] = { 0 }; diff --git a/Marlin/src/gcode/eeprom/M500-M504.cpp b/Marlin/src/gcode/eeprom/M500-M504.cpp index 12e323bd7b..e21e125066 100644 --- a/Marlin/src/gcode/eeprom/M500-M504.cpp +++ b/Marlin/src/gcode/eeprom/M500-M504.cpp @@ -25,18 +25,11 @@ #include "../../core/serial.h" #include "../../inc/MarlinConfig.h" -#if ENABLED(EXTENSIBLE_UI) - #include "../../lcd/extensible_ui/ui_api.h" -#endif - /** * M500: Store settings in EEPROM */ void GcodeSuite::M500() { (void)settings.save(); - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onStoreSettings(); - #endif } /** @@ -44,9 +37,6 @@ void GcodeSuite::M500() { */ void GcodeSuite::M501() { (void)settings.load(); - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onLoadSettings(); - #endif } /** @@ -54,9 +44,6 @@ void GcodeSuite::M501() { */ void GcodeSuite::M502() { (void)settings.reset(); - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onFactoryReset(); - #endif } #if DISABLED(DISABLE_M503) diff --git a/Marlin/src/gcode/feature/trinamic/M906.cpp b/Marlin/src/gcode/feature/trinamic/M906.cpp index 51a3cefde2..0466bfff4e 100644 --- a/Marlin/src/gcode/feature/trinamic/M906.cpp +++ b/Marlin/src/gcode/feature/trinamic/M906.cpp @@ -29,8 +29,18 @@ #include "../../../module/stepper_indirection.h" /** - * M906: Set motor current in milliamps using axis codes X, Y, Z, E - * Report driver currents when no axis specified + * M906: Set motor current in milliamps. + * + * Parameters: + * X[current] - Set mA current for X driver(s) + * Y[current] - Set mA current for Y driver(s) + * Z[current] - Set mA current for Z driver(s) + * E[current] - Set mA current for E driver(s) + * + * I[index] - Axis sub-index (Omit or 0 for X, Y, Z; 1 for X2, Y2, Z2; 2 for Z3.) + * T[index] - Extruder index (Zero-based. Omit for E0 only.) + * + * With no parameters report driver currents. */ void GcodeSuite::M906() { #define TMC_SAY_CURRENT(Q) tmc_get_current(stepper##Q) diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 320dc00ec3..81c0678e3f 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -138,6 +138,8 @@ #elif ENABLED(MKS_MINI_12864) #define MINIPANEL + #define DEFAULT_LCD_CONTRAST 150 + #define LCD_CONTRAST_MAX 255 #elif ENABLED(FYSETC_MINI_12864) @@ -153,7 +155,9 @@ #if EITHER(MAKRPANEL, MINIPANEL) #define DOGLCD #define ULTIPANEL - #define DEFAULT_LCD_CONTRAST 17 + #ifndef DEFAULT_LCD_CONTRAST + #define DEFAULT_LCD_CONTRAST 17 + #endif #endif #if ENABLED(ULTI_CONTROLLER) @@ -325,7 +329,7 @@ /** * Default LCD contrast for Graphical LCD displays */ -#define HAS_LCD_CONTRAST HAS_GRAPHICAL_LCD && defined(DEFAULT_LCD_CONTRAST) +#define HAS_LCD_CONTRAST (HAS_GRAPHICAL_LCD && defined(DEFAULT_LCD_CONTRAST)) #if HAS_LCD_CONTRAST #ifndef LCD_CONTRAST_MIN #define LCD_CONTRAST_MIN 0 @@ -562,3 +566,5 @@ #if ENABLED(SLIM_LCD_MENUS) #define BOOT_MARLIN_LOGO_SMALL #endif + +#define IS_RE_ARM_BOARD (MB(RAMPS_14_RE_ARM_EFB) || MB(RAMPS_14_RE_ARM_EEB) || MB(RAMPS_14_RE_ARM_EFF) || MB(RAMPS_14_RE_ARM_EEF) || MB(RAMPS_14_RE_ARM_SF)) diff --git a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp index c8927725c5..57a6e96904 100644 --- a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp +++ b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp @@ -1038,9 +1038,7 @@ void MarlinUI::draw_status_screen() { } void draw_select_screen(PGM_P const yes, PGM_P const no, const bool yesno, PGM_P const pref, const char * const string, PGM_P const suff) { - SETCURSOR(0, 0); lcd_put_u8str_P(pref); - if (string) wrap_string(1, string); - if (suff) lcd_put_u8str_P(suff); + ui.draw_select_screen_prompt(pref, string, suff); SETCURSOR(0, LCD_HEIGHT - 1); lcd_put_wchar(yesno ? ' ' : '['); lcd_put_u8str_P(no); lcd_put_wchar(yesno ? ' ' : ']'); SETCURSOR_RJ(utf8_strlen_P(yes) + 2, LCD_HEIGHT - 1); diff --git a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h index 7141eeb180..d25b58d9a4 100644 --- a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h +++ b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h @@ -94,3 +94,16 @@ public: : U8GLIB(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset) { } }; + + +extern u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, u8g_dev_uc1701_mini12864_HAL_2x_hw_spi; + +class U8GLIB_MINI12864_2X_HAL : public U8GLIB { +public: + U8GLIB_MINI12864_2X_HAL(uint8_t sck, uint8_t mosi, uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset) + { } + U8GLIB_MINI12864_2X_HAL(uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset) + { } +}; diff --git a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp index a72b3e4fc8..8b12a83570 100644 --- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp +++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp @@ -158,9 +158,7 @@ void ST7920_Lite_Status_Screen::entry_mode_select(const bool ac_increase, const // function for scroll_or_addr_select() void ST7920_Lite_Status_Screen::_scroll_or_addr_select(const bool sa) { extended_function_set(true); - cmd(0b00100010 | - (sa ? 0b000001 : 0) - ); + cmd(0b00000010 | (sa ? 0b00000001 : 0)); current_bits.sa = sa; } @@ -907,34 +905,6 @@ void ST7920_Lite_Status_Screen::clear_text_buffer() { ncs(); } -#if ENABLED(U8GLIB_ST7920) && !defined(U8G_HAL_LINKS) && !defined(__SAM3X8E__) - - #include "ultralcd_st7920_u8glib_rrd_AVR.h" - - void ST7920_Lite_Status_Screen::cs() { - ST7920_CS(); - current_bits.synced = false; - } - - void ST7920_Lite_Status_Screen::ncs() { - ST7920_NCS(); - current_bits.synced = false; - } - - void ST7920_Lite_Status_Screen::sync_cmd() { - ST7920_SET_CMD(); - } - - void ST7920_Lite_Status_Screen::sync_dat() { - ST7920_SET_DAT(); - } - - void ST7920_Lite_Status_Screen::write_byte(const uint8_t data) { - ST7920_WRITE_BYTE(data); - } - -#endif - void MarlinUI::draw_status_screen() { ST7920_Lite_Status_Screen::update(false); } diff --git a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h index 8a19030d6b..1fb707ca1d 100644 --- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h +++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h @@ -15,6 +15,8 @@ */ #pragma once +#include "../../HAL/shared/HAL_ST7920.h" + #include "../../core/macros.h" #include "../../libs/duration_t.h" @@ -28,11 +30,11 @@ class ST7920_Lite_Status_Screen { uint8_t sa : 1; } current_bits; - static void cs(); - static void ncs(); - static void sync_cmd(); - static void sync_dat(); - static void write_byte(const uint8_t w); + static void cs() { ST7920_cs(); current_bits.synced = false; } + static void ncs() { ST7920_cs(); current_bits.synced = false; } + static void sync_cmd() { ST7920_set_cmd(); } + static void sync_dat() { ST7920_set_dat(); } + static void write_byte(const uint8_t w) { ST7920_write_byte(w); } FORCE_INLINE static void write_word(const uint16_t w) { write_byte((w >> 8) & 0xFF); diff --git a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp index 35f7d4161a..4dd8759e7a 100644 --- a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp +++ b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp @@ -66,42 +66,47 @@ #define PAGE_HEIGHT 8 static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = { - U8G_ESC_CS(0), /* disable chip */ - U8G_ESC_ADR(0), /* instruction mode */ - U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */ - U8G_ESC_CS(1), /* enable chip */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_ADR(0), /* instruction mode */ + U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */ + U8G_ESC_CS(1), /* enable chip */ - 0x0E2, /* soft reset */ - 0x040, /* set display start line to 0 */ - 0x0A0, /* ADC set to reverse */ - 0x0C8, /* common output mode */ - 0x0A6, /* display normal, bit val 0: LCD pixel off. */ - 0x0A2, /* LCD bias 1/9 */ - 0x02F, /* all power control circuits on */ - 0x0F8, /* set booster ratio to */ - 0x000, /* 4x */ - 0x023, /* set V0 voltage resistor ratio to large */ - 0x081, /* set contrast */ - 0x027, /* contrast value */ - 0x0AC, /* indicator */ - 0x000, /* disable */ - 0x0AF, /* display on */ + 0x0E2, /* soft reset */ + 0x040, /* set display start line to 0 */ + 0x0A0, /* ADC set to reverse */ + 0x0C8, /* common output mode */ + 0x0A6, /* display normal, bit val 0: LCD pixel off. */ + 0x0A2, /* LCD bias 1/9 */ + 0x02F, /* all power control circuits on */ + 0x0F8, /* set booster ratio to */ + 0x000, /* 4x */ + 0x023, /* set V0 voltage resistor ratio to large */ + 0x081, /* set contrast */ + 0x027, /* contrast value */ + 0x0AC, /* indicator */ + 0x000, /* disable */ + 0x0AF, /* display on */ - U8G_ESC_DLY(100), /* delay 100 ms */ - 0x0A5, /* display all points, ST7565 */ - U8G_ESC_DLY(100), /* delay 100 ms */ - U8G_ESC_DLY(100), /* delay 100 ms */ - 0x0A4, /* normal display */ - U8G_ESC_CS(0), /* disable chip */ - U8G_ESC_END /* end of sequence */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_CS(1), /* enable chip */ + + 0x0A5, /* display all points, ST7565 */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_CS(1), /* enable chip */ + 0x0A4, /* normal display */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_END /* end of sequence */ }; static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = { - U8G_ESC_ADR(0), /* instruction mode */ - U8G_ESC_CS(1), /* enable chip */ - 0x010, /* set upper 4 bit of the col adr to 0 */ - 0x000, /* set lower 4 bit of the col adr to 4 */ - U8G_ESC_END /* end of sequence */ + U8G_ESC_ADR(0), /* instruction mode */ + U8G_ESC_CS(1), /* enable chip */ + 0x010, /* set upper 4 bit of the col adr to 0 */ + 0x000, /* set lower 4 bit of the col adr to 4 */ + U8G_ESC_END /* end of sequence */ }; uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) { diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp index 4ef6fc6248..4a33045592 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp @@ -175,14 +175,14 @@ void MarlinUI::set_font(const MarlinFont font_nr) { // Can the text fit to the right of the bitmap? if (text_max_width < rspace) { - constexpr uint8_t inter = (width - text_max_width - (START_BMPWIDTH)) / 3; // Evenly distribute horizontal space + constexpr int8_t inter = (width - text_max_width - (START_BMPWIDTH)) / 3; // Evenly distribute horizontal space offx = inter; // First the boot logo... offy = (height - (START_BMPHEIGHT)) / 2; // ...V-aligned in the full height txt_offx_1 = txt_offx_2 = inter + (START_BMPWIDTH) + inter; // Text right of the bitmap txt_base = (height + MENU_FONT_ASCENT + text_total_height - (MENU_FONT_HEIGHT)) / 2; // Text vertical center } else { - constexpr uint8_t inter = (height - text_total_height - (START_BMPHEIGHT)) / 3; // Evenly distribute vertical space + constexpr int8_t inter = (height - text_total_height - (START_BMPHEIGHT)) / 3; // Evenly distribute vertical space offy = inter; // V-align boot logo proportionally offx = rspace / 2; // Center the boot logo in the whole space txt_offx_1 = (width - text_width_1) / 2; // Text 1 centered @@ -439,9 +439,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop } void draw_select_screen(PGM_P const yes, PGM_P const no, const bool yesno, PGM_P const pref, const char * const string, PGM_P const suff) { - SETCURSOR(0, 0); lcd_put_u8str_P(pref); - if (string) wrap_string(1, string); - if (suff) lcd_put_u8str_P(suff); + ui.draw_select_screen_prompt(pref, string, suff); draw_boxed_string(1, LCD_HEIGHT - 1, no, !yesno); draw_boxed_string(LCD_WIDTH - (utf8_strlen_P(yes) + 1), LCD_HEIGHT - 1, yes, yesno); } diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.h b/Marlin/src/lcd/dogm/ultralcd_DOGM.h index 1f2c90b9d9..8ce25d0e77 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.h +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.h @@ -111,8 +111,8 @@ // The MINIPanel display //#define U8G_CLASS U8GLIB_MINI12864 //#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes - #define U8G_CLASS U8GLIB_MINI12864_2X - #if EITHER(FYSETC_MINI_12864, TARGET_LPC1768) + #define U8G_CLASS U8GLIB_MINI12864_2X_HAL + #if BOTH(FYSETC_MINI_12864, FORCE_SOFT_SPI) #define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI #else #define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI diff --git a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp index c99a7085a1..969cef10bb 100644 --- a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp +++ b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp @@ -134,4 +134,13 @@ u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = {u8g_dev_rrd_st7920_128x64_fn, &u8g #pragma GCC reset_options +#if ENABLED(LIGHTWEIGHT_UI) + #include "../../HAL/shared/HAL_ST7920.h" + void ST7920_cs() { ST7920_CS(); } + void ST7920_ncs() { ST7920_NCS(); } + void ST7920_set_cmd() { ST7920_SET_CMD(); } + void ST7920_set_dat() { ST7920_SET_DAT(); } + void ST7920_write_byte(const uint8_t val) { ST7920_WRITE_BYTE(val); } +#endif + #endif // U8GLIB_ST7920 && !U8G_HAL_LINKS && !__SAM3X8E__ diff --git a/Marlin/src/lcd/language/language_de.h b/Marlin/src/lcd/language/language_de.h index 3fa3be90ef..9275b08643 100644 --- a/Marlin/src/lcd/language/language_de.h +++ b/Marlin/src/lcd/language/language_de.h @@ -332,9 +332,11 @@ #define MSG_ENDSTOP_ABORT _UxGT("Endstopp Abbr.") #define MSG_HEATING_FAILED_LCD _UxGT("HEIZEN ERFOLGLOS") #define MSG_HEATING_FAILED_LCD_BED _UxGT("Bett heizen fehlge.") +#define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Geh. heizen fehlge.") #define MSG_ERR_REDUNDANT_TEMP _UxGT("REDUND. TEMP-ABWEI.") #define MSG_THERMAL_RUNAWAY LCD_STR_THERMOMETER _UxGT(" NICHT ERREICHT") #define MSG_THERMAL_RUNAWAY_BED _UxGT("BETT") MSG_THERMAL_RUNAWAY +#define MSG_THERMAL_RUNAWAY_CHAMBER _UxGT("GEH.") MSG_THERMAL_RUNAWAY #define MSG_ERR_MAXTEMP LCD_STR_THERMOMETER _UxGT(" ÜBERSCHRITTEN") #define MSG_ERR_MINTEMP LCD_STR_THERMOMETER _UxGT(" UNTERSCHRITTEN") #define MSG_ERR_MAXTEMP_BED _UxGT("BETT ") LCD_STR_THERMOMETER _UxGT(" ÜBERSCHRITTEN") diff --git a/Marlin/src/lcd/language/language_en.h b/Marlin/src/lcd/language/language_en.h index c60f8b8051..5677ecbae9 100644 --- a/Marlin/src/lcd/language/language_en.h +++ b/Marlin/src/lcd/language/language_en.h @@ -753,12 +753,27 @@ #ifndef MSG_START_PRINT #define MSG_START_PRINT _UxGT("Start print") #endif +#ifndef MSG_BUTTON_NEXT + #define MSG_BUTTON_NEXT _UxGT("Next") +#endif +#ifndef MSG_BUTTON_INIT + #define MSG_BUTTON_INIT _UxGT("Init") +#endif +#ifndef MSG_BUTTON_STOP + #define MSG_BUTTON_STOP _UxGT("Stop") +#endif #ifndef MSG_BUTTON_PRINT #define MSG_BUTTON_PRINT _UxGT("Print") #endif +#ifndef MSG_BUTTON_RESET + #define MSG_BUTTON_RESET _UxGT("Reset") +#endif #ifndef MSG_BUTTON_CANCEL #define MSG_BUTTON_CANCEL _UxGT("Cancel") #endif +#ifndef MSG_BUTTON_DONE + #define MSG_BUTTON_DONE _UxGT("Done") +#endif #ifndef MSG_PAUSE_PRINT #define MSG_PAUSE_PRINT _UxGT("Pause print") #endif @@ -930,6 +945,9 @@ #ifndef MSG_HEATING_FAILED_LCD_BED #define MSG_HEATING_FAILED_LCD_BED _UxGT("Bed heating failed") #endif +#ifndef MSG_HEATING_FAILED_LCD_CHAMBER + #define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Chamber heating fail") +#endif #ifndef MSG_ERR_REDUNDANT_TEMP #define MSG_ERR_REDUNDANT_TEMP _UxGT("Err: REDUNDANT TEMP") #endif @@ -939,6 +957,9 @@ #ifndef MSG_THERMAL_RUNAWAY_BED #define MSG_THERMAL_RUNAWAY_BED _UxGT("BED THERMAL RUNAWAY") #endif +#ifndef MSG_THERMAL_RUNAWAY_CHAMBER + #define MSG_THERMAL_RUNAWAY_CHAMBER _UxGT("CHAMBER T. RUNAWAY") +#endif #ifndef MSG_ERR_MAXTEMP #define MSG_ERR_MAXTEMP _UxGT("Err: MAXTEMP") #endif diff --git a/Marlin/src/lcd/language/language_fr.h b/Marlin/src/lcd/language/language_fr.h index 058062ee91..e45bb3277d 100644 --- a/Marlin/src/lcd/language/language_fr.h +++ b/Marlin/src/lcd/language/language_fr.h @@ -33,19 +33,25 @@ #define CHARSIZE 2 #define WELCOME_MSG MACHINE_NAME _UxGT(" prête.") +#define MSG_YES _UxGT("Oui") +#define MSG_NO _UxGT("Non") #define MSG_BACK _UxGT("Retour") #define MSG_SD_INSERTED _UxGT("Carte insérée") #define MSG_SD_REMOVED _UxGT("Carte retirée") -#define MSG_LCD_ENDSTOPS _UxGT("Butées") // Max length 8 characters +#define MSG_LCD_ENDSTOPS _UxGT("Butées") +#define MSG_LCD_SOFT_ENDSTOPS _UxGT("Butées SW") #define MSG_MAIN _UxGT("Menu principal") -#define MSG_AUTOSTART _UxGT("Demarrage auto") +#define MSG_ADVANCED_SETTINGS _UxGT("Config. avancée") +#define MSG_CONFIGURATION _UxGT("Configuration") +#define MSG_AUTOSTART _UxGT("Exéc. auto#.gcode") #define MSG_DISABLE_STEPPERS _UxGT("Arrêter moteurs") #define MSG_DEBUG_MENU _UxGT("Menu debug") #define MSG_PROGRESS_BAR_TEST _UxGT("Test barre progress.") #define MSG_AUTO_HOME _UxGT("Origine auto.") -#define MSG_AUTO_HOME_X _UxGT("Origine X Auto.") -#define MSG_AUTO_HOME_Y _UxGT("Origine Y Auto.") -#define MSG_AUTO_HOME_Z _UxGT("Origine Z Auto.") +#define MSG_AUTO_HOME_X _UxGT("Origine X auto.") +#define MSG_AUTO_HOME_Y _UxGT("Origine Y auto.") +#define MSG_AUTO_HOME_Z _UxGT("Origine Z auto.") +#define MSG_AUTO_Z_ALIGN _UxGT("Align. Z auto.") #define MSG_LEVEL_BED_HOMING _UxGT("Origine XYZ") #define MSG_LEVEL_BED_WAITING _UxGT("Clic pour commencer") #define MSG_LEVEL_BED_NEXT_POINT _UxGT("Point suivant") @@ -59,14 +65,20 @@ #define MSG_PREHEAT_1_ALL _UxGT("Préch. " PREHEAT_1_LABEL " Tout") #define MSG_PREHEAT_1_END MSG_PREHEAT_1 _UxGT(" buse") #define MSG_PREHEAT_1_BEDONLY _UxGT("Préch. " PREHEAT_1_LABEL " lit") -#define MSG_PREHEAT_1_SETTINGS _UxGT("Régl. prech. " PREHEAT_1_LABEL) +#define MSG_PREHEAT_1_SETTINGS _UxGT("Régl. préch. " PREHEAT_1_LABEL) #define MSG_PREHEAT_2 _UxGT("Préchauffage " PREHEAT_2_LABEL) #define MSG_PREHEAT_2_N _UxGT("Préchauff. " PREHEAT_2_LABEL " ") #define MSG_PREHEAT_2_ALL _UxGT("Préch. " PREHEAT_2_LABEL " Tout") #define MSG_PREHEAT_2_END MSG_PREHEAT_2 _UxGT(" buse") #define MSG_PREHEAT_2_BEDONLY _UxGT("Préch. " PREHEAT_2_LABEL " lit") -#define MSG_PREHEAT_2_SETTINGS _UxGT("Régl. prech. " PREHEAT_2_LABEL) +#define MSG_PREHEAT_2_SETTINGS _UxGT("Régl. préch. " PREHEAT_2_LABEL) +#define MSG_PREHEAT_CUSTOM _UxGT("Préchauff. perso.") #define MSG_COOLDOWN _UxGT("Refroidir") +#define MSG_LASER_MENU _UxGT("Contrôle Laser") +#define MSG_LASER_OFF _UxGT("Laser Off") +#define MSG_LASER_ON _UxGT("Laser On") +#define MSG_LASER_POWER _UxGT("Puissance") +#define MSG_SPINDLE_REVERSE _UxGT("Inverser broches") #define MSG_SWITCH_PS_ON _UxGT("Allumer alim.") #define MSG_SWITCH_PS_OFF _UxGT("Eteindre alim.") #define MSG_EXTRUDE _UxGT("Extrusion") @@ -77,12 +89,24 @@ #define MSG_LEVEL_CORNERS _UxGT("Niveau coins") #define MSG_NEXT_CORNER _UxGT("Coin suivant") #define MSG_EDITING_STOPPED _UxGT("Arrêt édit. maillage") -#define MSG_USER_MENU _UxGT("Commandes perso") +#define MSG_MESH_X _UxGT("Index X") +#define MSG_MESH_Y _UxGT("Index Y") +#define MSG_MESH_EDIT_Z _UxGT("Valeur Z") +#define MSG_USER_MENU _UxGT("Commandes perso.") #define MSG_UBL_DOING_G29 _UxGT("G29 en cours") #define MSG_UBL_UNHOMED _UxGT("Origine XYZ d'abord") #define MSG_UBL_TOOLS _UxGT("Outils UBL") #define MSG_UBL_LEVEL_BED _UxGT("Niveau lit unifié") +#define MSG_IDEX_MENU _UxGT("Mode IDEX") +#define MSG_IDEX_MODE_AUTOPARK _UxGT("Auto-Park") +#define MSG_IDEX_MODE_DUPLICATE _UxGT("Duplication") +#define MSG_IDEX_MODE_MIRRORED_COPY _UxGT("Copie miroir") +#define MSG_IDEX_MODE_FULL_CTRL _UxGT("Contrôle complet") +#define MSG_OFFSETS_MENU _UxGT("Offsets Outil") +#define MSG_X_OFFSET _UxGT("Buse 2 X") +#define MSG_Y_OFFSET _UxGT("Buse 2 Y") +#define MSG_Z_OFFSET _UxGT("Buse 2 Z") #define MSG_UBL_MANUAL_MESH _UxGT("Maillage manuel") #define MSG_UBL_BC_INSERT _UxGT("Poser câle & mesurer") #define MSG_UBL_BC_INSERT2 _UxGT("Mesure") @@ -167,6 +191,7 @@ #define MSG_MOVE_Y _UxGT("Dépl. Y") #define MSG_MOVE_Z _UxGT("Dépl. Z") #define MSG_MOVE_E _UxGT("Extrudeur") +#define MSG_HOTEND_TOO_COLD _UxGT("Buse trop froide") #define MSG_MOVE_01MM _UxGT("Dépl. 0.1mm") #define MSG_MOVE_1MM _UxGT("Dépl. 1mm") #define MSG_MOVE_10MM _UxGT("Dépl. 10mm") @@ -174,6 +199,7 @@ #define MSG_BED_Z _UxGT("Lit Z") #define MSG_NOZZLE _UxGT("Buse") #define MSG_BED _UxGT("Lit") +#define MSG_CHAMBER _UxGT("Caisson") #define MSG_FAN_SPEED _UxGT("Vitesse ventil.") #define MSG_EXTRA_FAN_SPEED _UxGT("Extra V ventil.") @@ -203,6 +229,7 @@ #endif #define MSG_VE_JERK _UxGT("Ve jerk") #define MSG_VELOCITY _UxGT("Vélocité") +#define MSG_JUNCTION_DEVIATION _UxGT("Déviat. jonct.") #define MSG_VMAX _UxGT("Vmax ") #define MSG_VMIN _UxGT("Vmin ") #define MSG_VTRAV_MIN _UxGT("V dépl. min") @@ -240,19 +267,26 @@ #define MSG_LOAD_EEPROM _UxGT("Lire config") #define MSG_RESTORE_FAILSAFE _UxGT("Restaurer défauts") #define MSG_INIT_EEPROM _UxGT("Initialiser EEPROM") +#define MSG_SD_UPDATE _UxGT("MàJ. SD") +#define MSG_RESET_PRINTER _UxGT("RàZ. imprimante") #define MSG_REFRESH _UxGT("Actualiser") #define MSG_WATCH _UxGT("Surveiller") #define MSG_PREPARE _UxGT("Préparer") #define MSG_TUNE _UxGT("Régler") +#define MSG_START_PRINT _UxGT("Démarrer Impr.") +#define MSG_BUTTON_PRINT _UxGT("Imprimer") +#define MSG_BUTTON_CANCEL _UxGT("Annuler") #define MSG_PAUSE_PRINT _UxGT("Interrompre impr.") #define MSG_RESUME_PRINT _UxGT("Reprendre impr.") #define MSG_STOP_PRINT _UxGT("Arrêter impr.") +#define MSG_OUTAGE_RECOVERY _UxGT("Récupér. coupure") #define MSG_CARD_MENU _UxGT("Impr. depuis SD") #define MSG_NO_CARD _UxGT("Pas de carte") #define MSG_DWELL _UxGT("Repos...") -#define MSG_USERWAIT _UxGT("Atten. de l'util.") +#define MSG_USERWAIT _UxGT("Attente utilis.") #define MSG_PRINT_PAUSED _UxGT("Impr. en pause") -#define MSG_PRINT_ABORTED _UxGT("Impr. Annulée") +#define MSG_PRINTING _UxGT("Impression") +#define MSG_PRINT_ABORTED _UxGT("Impr. annulée") #define MSG_NO_MOVE _UxGT("Moteurs bloqués.") #define MSG_KILLED _UxGT("MORT.") #define MSG_STOPPED _UxGT("STOPPÉ.") @@ -264,34 +298,50 @@ #define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("Ech. Rappel mm") #define MSG_CONTROL_RETRACT_RECOVERF _UxGT("Rappel V") #define MSG_CONTROL_RETRACT_RECOVER_SWAPF _UxGT("Ech. Rappel V") -#define MSG_AUTORETRACT _UxGT("Retrait. Auto.") +#define MSG_AUTORETRACT _UxGT("Retrait auto.") +#define MSG_TOOL_CHANGE _UxGT("Changement outil") +#define MSG_TOOL_CHANGE_ZLIFT _UxGT("Augmenter Z") +#define MSG_SINGLENOZZLE_PRIME_SPD _UxGT("Vitesse primaire") +#define MSG_SINGLENOZZLE_RETRACT_SPD _UxGT("Vitesse retrait") +#define MSG_NOZZLE_STANDBY _UxGT("Attente buse") +#define MSG_FILAMENT_SWAP_LENGTH _UxGT("Distance retrait") #define MSG_FILAMENTCHANGE _UxGT("Changer filament") #define MSG_FILAMENTLOAD _UxGT("Charger fil.") #define MSG_FILAMENTUNLOAD _UxGT("Décharger fil.") #define MSG_FILAMENTUNLOAD_ALL _UxGT("Décharger tout") #define MSG_INIT_SDCARD _UxGT("Init. la carte SD") #define MSG_CHANGE_SDCARD _UxGT("Changer de carte") -#define MSG_ZPROBE_OUT _UxGT("Z sonde hors lit") +#define MSG_ZPROBE_OUT _UxGT("Sonde Z hors lit") #define MSG_SKEW_FACTOR _UxGT("Facteur écart") #define MSG_BLTOUCH _UxGT("BLTouch") #define MSG_BLTOUCH_SELFTEST _UxGT("Autotest BLTouch") #define MSG_BLTOUCH_RESET _UxGT("RaZ BLTouch") #define MSG_BLTOUCH_DEPLOY _UxGT("Déployer BLTouch") +#define MSG_BLTOUCH_SW_MODE _UxGT("Mode BLTouch SW") +#define MSG_BLTOUCH_5V_MODE _UxGT("Mode BLTouch 5V") +#define MSG_BLTOUCH_OD_MODE _UxGT("Mode BLTouch OD") #define MSG_BLTOUCH_STOW _UxGT("Ranger BLTouch") +#define MSG_MANUAL_DEPLOY _UxGT("Déployer Sonde Z") +#define MSG_MANUAL_STOW _UxGT("Ranger Sonde Z") #define MSG_HOME _UxGT("Origine") // Used as MSG_HOME " " MSG_X MSG_Y MSG_Z " " MSG_FIRST #define MSG_FIRST _UxGT("Premier") #define MSG_ZPROBE_ZOFFSET _UxGT("Décalage Z") #define MSG_BABYSTEP_X _UxGT("Babystep X") #define MSG_BABYSTEP_Y _UxGT("Babystep Y") #define MSG_BABYSTEP_Z _UxGT("Babystep Z") +#define MSG_BABYSTEP_TOTAL _UxGT("Total") #define MSG_ENDSTOP_ABORT _UxGT("Butée abandon") #define MSG_HEATING_FAILED_LCD _UxGT("Erreur de chauffe") +#define MSG_HEATING_FAILED_LCD_BED _UxGT("Erreur de chauffe lit") #define MSG_ERR_REDUNDANT_TEMP _UxGT("Err: TEMP. REDONDANTE") #define MSG_THERMAL_RUNAWAY _UxGT("EMBALLEMENT THERM.") +#define MSG_THERMAL_RUNAWAY_BED _UxGT("ERREUR THERMIQUE LIT") #define MSG_ERR_MAXTEMP _UxGT("Err: TEMP. MAX") #define MSG_ERR_MINTEMP _UxGT("Err: TEMP. MIN") #define MSG_ERR_MAXTEMP_BED _UxGT("Err: TEMP. MAX LIT") #define MSG_ERR_MINTEMP_BED _UxGT("Err: TEMP. MIN LIT") +#define MSG_ERR_MAXTEMP_CHAMBER _UxGT("Err: MAXTEMP CAISSON") +#define MSG_ERR_MINTEMP_CHAMBER _UxGT("Err: MINTEMP CAISSON") #define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST #define MSG_HALTED _UxGT("IMPR. STOPPÉE") @@ -301,7 +351,9 @@ #define MSG_SHORT_MINUTE _UxGT("m") // One character only #define MSG_HEATING _UxGT("En chauffe...") +#define MSG_COOLING _UxGT("Refroidissement") #define MSG_BED_HEATING _UxGT("Lit en chauffe...") +#define MSG_BED_COOLING _UxGT("Refroid. du lit...") #define MSG_DELTA_CALIBRATE _UxGT("Calibration Delta") #define MSG_DELTA_CALIBRATE_X _UxGT("Calibrer X") #define MSG_DELTA_CALIBRATE_Y _UxGT("Calibrer Y") @@ -310,6 +362,7 @@ #define MSG_DELTA_SETTINGS _UxGT("Réglages Delta") #define MSG_DELTA_AUTO_CALIBRATE _UxGT("Calibration Auto") #define MSG_DELTA_HEIGHT_CALIBRATE _UxGT("Hauteur Delta") +#define MSG_DELTA_Z_OFFSET_CALIBRATE _UxGT("Delta Z sonde") #define MSG_DELTA_DIAG_ROD _UxGT("Diagonale") #define MSG_DELTA_HEIGHT _UxGT("Hauteur") #define MSG_DELTA_RADIUS _UxGT("Rayon") @@ -323,9 +376,9 @@ #define MSG_MESH_LEVELING _UxGT("Niveau maillage") #define MSG_INFO_STATS_MENU _UxGT("Stats. imprimante") #define MSG_INFO_BOARD_MENU _UxGT("Infos carte") -#define MSG_INFO_THERMISTOR_MENU _UxGT("Thermistors") +#define MSG_INFO_THERMISTOR_MENU _UxGT("Thermistances") #define MSG_INFO_EXTRUDERS _UxGT("Extrudeurs") -#define MSG_INFO_BAUDRATE _UxGT("Baud") +#define MSG_INFO_BAUDRATE _UxGT("Bauds") #define MSG_INFO_PROTOCOL _UxGT("Protocole") #define MSG_CASE_LIGHT _UxGT("Lumière caisson") #define MSG_CASE_LIGHT_BRIGHTNESS _UxGT("Luminosité") @@ -358,35 +411,109 @@ #define MSG_FILAMENT_CHANGE_OPTION_PURGE _UxGT("Purger encore") #define MSG_FILAMENT_CHANGE_OPTION_RESUME _UxGT("Reprendre impr.") #define MSG_FILAMENT_CHANGE_NOZZLE _UxGT(" Buse: ") +#define MSG_RUNOUT_SENSOR _UxGT("Capteur Fil.") #define MSG_ERR_HOMING_FAILED _UxGT("Echec origine") #define MSG_ERR_PROBING_FAILED _UxGT("Echec sonde") #define MSG_M600_TOO_COLD _UxGT("M600: Trop froid") +#define MSG_MMU2_FILAMENT_CHANGE_HEADER _UxGT("CHANGER FILAMENT") +#define MSG_MMU2_CHOOSE_FILAMENT_HEADER _UxGT("CHOISIR FILAMENT") +#define MSG_MMU2_MENU _UxGT("MMU") +#define MSG_MMU2_WRONG_FIRMWARE _UxGT("Update MMU firmware!") +#define MSG_MMU2_NOT_RESPONDING _UxGT("MMU ne répond plus") +#define MSG_MMU2_RESUME _UxGT("Continuer impr.") +#define MSG_MMU2_RESUMING _UxGT("Reprise...") +#define MSG_MMU2_LOAD_FILAMENT _UxGT("Charger filament") +#define MSG_MMU2_LOAD_ALL _UxGT("Charger tous") +#define MSG_MMU2_LOAD_TO_NOZZLE _UxGT("Charger dans buse") +#define MSG_MMU2_EJECT_FILAMENT _UxGT("Ejecter filament") +#define MSG_MMU2_EJECT_FILAMENT0 _UxGT("Ejecter fil. 1") +#define MSG_MMU2_EJECT_FILAMENT1 _UxGT("Ejecter fil. 2") +#define MSG_MMU2_EJECT_FILAMENT2 _UxGT("Ejecter fil. 3") +#define MSG_MMU2_EJECT_FILAMENT3 _UxGT("Ejecter fil. 4") +#define MSG_MMU2_EJECT_FILAMENT4 _UxGT("Ejecter fil. 5") +#define MSG_MMU2_UNLOAD_FILAMENT _UxGT("Retrait filament") +#define MSG_MMU2_LOADING_FILAMENT _UxGT("Chargem. fil. %i...") +#define MSG_MMU2_EJECTING_FILAMENT _UxGT("Ejection fil...") +#define MSG_MMU2_UNLOADING_FILAMENT _UxGT("Retrait fil....") +#define MSG_MMU2_ALL _UxGT("Tous") +#define MSG_MMU2_FILAMENT0 _UxGT("Filament 1") +#define MSG_MMU2_FILAMENT1 _UxGT("Filament 2") +#define MSG_MMU2_FILAMENT2 _UxGT("Filament 3") +#define MSG_MMU2_FILAMENT3 _UxGT("Filament 4") +#define MSG_MMU2_FILAMENT4 _UxGT("Filament 5") +#define MSG_MMU2_RESET _UxGT("Réinit. MMU") +#define MSG_MMU2_RESETTING _UxGT("Réinit. MMU...") +#define MSG_MMU2_EJECT_RECOVER _UxGT("Retrait, click") + +#define MSG_MIX _UxGT("Mix") +#define MSG_MIX_COMPONENT _UxGT("Composante") +#define MSG_MIXER _UxGT("Mixeur") +#define MSG_GRADIENT _UxGT("Dégradé") +#define MSG_FULL_GRADIENT _UxGT("Dégradé complet") +#define MSG_TOGGLE_MIX _UxGT("Toggle mix") +#define MSG_CYCLE_MIX _UxGT("Cycle mix") +#define MSG_GRADIENT_MIX _UxGT("Mix dégradé") +#define MSG_REVERSE_GRADIENT _UxGT("Inverser dégradé") +#define MSG_ACTIVE_VTOOL _UxGT("Active V-tool") +#define MSG_START_VTOOL _UxGT("Début V-tool") +#define MSG_END_VTOOL _UxGT(" Fin V-tool") +#define MSG_GRADIENT_ALIAS _UxGT("Alias V-tool") +#define MSG_RESET_VTOOLS _UxGT("Réinit. V-tools") +#define MSG_COMMIT_VTOOL _UxGT("Valider Mix V-tool") +#define MSG_VTOOLS_RESET _UxGT("V-tools réinit. ok") +#define MSG_START_Z _UxGT("Début Z") +#define MSG_END_Z _UxGT(" Fin Z") +#define MSG_BRICKOUT _UxGT("Casse-briques") +#define MSG_INVADERS _UxGT("Invaders") +#define MSG_SNAKE _UxGT("Sn4k3") +#define MSG_MAZE _UxGT("Labyrinthe") #if LCD_HEIGHT >= 4 // Up to 3 lines allowed - #define MSG_FILAMENT_CHANGE_INIT_1 _UxGT("Attente Démarrage") - #define MSG_FILAMENT_CHANGE_INIT_2 _UxGT("du filament") - #define MSG_FILAMENT_CHANGE_INIT_3 _UxGT("changer") - #define MSG_FILAMENT_CHANGE_UNLOAD_1 _UxGT("Attente de") - #define MSG_FILAMENT_CHANGE_UNLOAD_2 _UxGT("décharger filament") + #define MSG_ADVANCED_PAUSE_WAITING_1 _UxGT("Presser bouton") + #define MSG_ADVANCED_PAUSE_WAITING_2 _UxGT("pour reprendre") + #define MSG_PAUSE_PRINT_INIT_1 _UxGT("Parking...") + #define MSG_FILAMENT_CHANGE_INIT_1 _UxGT("Attente filament") + #define MSG_FILAMENT_CHANGE_INIT_2 _UxGT("pour démarrer") #define MSG_FILAMENT_CHANGE_INSERT_1 _UxGT("Insérer filament") #define MSG_FILAMENT_CHANGE_INSERT_2 _UxGT("et app. bouton") #define MSG_FILAMENT_CHANGE_INSERT_3 _UxGT("pour continuer...") #define MSG_FILAMENT_CHANGE_HEAT_1 _UxGT("Presser le bouton...") - #define MSG_FILAMENT_CHANGE_HEAT_2 _UxGT("Pr chauffer la buse") + #define MSG_FILAMENT_CHANGE_HEAT_2 _UxGT("pr chauffer la buse") #define MSG_FILAMENT_CHANGE_HEATING_1 _UxGT("Buse en chauffe") - #define MSG_FILAMENT_CHANGE_HEATING_2 _UxGT("Patientez SVP...") - #define MSG_FILAMENT_CHANGE_LOAD_1 _UxGT("Attente de") - #define MSG_FILAMENT_CHANGE_LOAD_2 _UxGT("Chargement filament") + #define MSG_FILAMENT_CHANGE_HEATING_2 _UxGT("Patienter SVP...") + #define MSG_FILAMENT_CHANGE_UNLOAD_1 _UxGT("Attente") + #define MSG_FILAMENT_CHANGE_UNLOAD_2 _UxGT("retrait du filament") + #define MSG_FILAMENT_CHANGE_LOAD_1 _UxGT("Attente") + #define MSG_FILAMENT_CHANGE_LOAD_2 _UxGT("chargement filament") #define MSG_FILAMENT_CHANGE_PURGE_1 _UxGT("Attente") - #define MSG_FILAMENT_CHANGE_PURGE_2 _UxGT("Purger filament") - #define MSG_FILAMENT_CHANGE_RESUME_1 _UxGT("Attente impression") - #define MSG_FILAMENT_CHANGE_RESUME_2 _UxGT("pour reprendre") + #define MSG_FILAMENT_CHANGE_PURGE_2 _UxGT("Purge filament") + #define MSG_FILAMENT_CHANGE_CONT_PURGE_1 _UxGT("Presser pour finir") + #define MSG_FILAMENT_CHANGE_CONT_PURGE_2 _UxGT("la purge du filament") + #define MSG_FILAMENT_CHANGE_RESUME_1 _UxGT("Attente reprise") + #define MSG_FILAMENT_CHANGE_RESUME_2 _UxGT("impression") #else // LCD_HEIGHT < 4 // Up to 2 lines allowed - #define MSG_FILAMENT_CHANGE_INIT_1 _UxGT("Patientez...") - #define MSG_FILAMENT_CHANGE_UNLOAD_1 _UxGT("Ejection...") - #define MSG_FILAMENT_CHANGE_INSERT_1 _UxGT("Insérer et clic") + #define MSG_ADVANCED_PAUSE_WAITING_1 _UxGT("Presser pr continuer") + #define MSG_FILAMENT_CHANGE_INIT_1 _UxGT("Patience...") + #define MSG_FILAMENT_CHANGE_INSERT_1 _UxGT("Insérer fil.") + #define MSG_FILAMENT_CHANGE_HEAT_1 _UxGT("Chauffer ?") + #define MSG_FILAMENT_CHANGE_HEATING_1 _UxGT("Chauffage...") + #define MSG_FILAMENT_CHANGE_UNLOAD_1 _UxGT("Ejecting...") #define MSG_FILAMENT_CHANGE_LOAD_1 _UxGT("Chargement...") + #define MSG_FILAMENT_CHANGE_PURGE_1 _UxGT("Purge...") + #define MSG_FILAMENT_CHANGE_CONT_PURGE_1 _UxGT("Terminer ?") #define MSG_FILAMENT_CHANGE_RESUME_1 _UxGT("Reprise...") #endif // LCD_HEIGHT < 4 + +#define MSG_TMC_DRIVERS _UxGT("Drivers TMC") +#define MSG_TMC_CURRENT _UxGT("Courant driver") +#define MSG_TMC_HYBRID_THRS _UxGT("Seuil hybride") +#define MSG_TMC_HOMING_THRS _UxGT("Home sans capteur") +#define MSG_TMC_STEPPING_MODE _UxGT("Mode pas à pas") +#define MSG_TMC_STEALTH_ENABLED _UxGT("StealthChop activé") +#define MSG_SERVICE_RESET _UxGT("Réinit.") +#define MSG_SERVICE_IN _UxGT(" dans:") +#define MSG_BACKLASH _UxGT("Backlash") +#define MSG_BACKLASH_CORRECTION _UxGT("Correction") +#define MSG_BACKLASH_SMOOTHING _UxGT("Lissage") diff --git a/Marlin/src/lcd/language/language_it.h b/Marlin/src/lcd/language/language_it.h index 36bfd70f19..78450b47bd 100644 --- a/Marlin/src/lcd/language/language_it.h +++ b/Marlin/src/lcd/language/language_it.h @@ -330,9 +330,11 @@ #define MSG_ENDSTOP_ABORT _UxGT("Finecorsa annullati") #define MSG_HEATING_FAILED_LCD _UxGT("Riscald. Fallito") #define MSG_HEATING_FAILED_LCD_BED _UxGT("Risc. piatto fallito") +#define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Risc. camera fallito") #define MSG_ERR_REDUNDANT_TEMP _UxGT("Err: TEMP RIDONDANTE") #define MSG_THERMAL_RUNAWAY _UxGT("TEMP FUORI CONTROLLO") #define MSG_THERMAL_RUNAWAY_BED _UxGT("TEMP PIAT.FUORI CTRL") +#define MSG_THERMAL_RUNAWAY_CHAMBER _UxGT("T.CAMERA FUORI CTRL") #define MSG_ERR_MAXTEMP _UxGT("Err: TEMP MASSIMA") #define MSG_ERR_MINTEMP _UxGT("Err: TEMP MINIMA") #define MSG_ERR_MAXTEMP_BED _UxGT("Err: TEMP MAX PIATTO") diff --git a/Marlin/src/lcd/menu/menu.cpp b/Marlin/src/lcd/menu/menu.cpp index 1a053ad850..ba6957ddaf 100644 --- a/Marlin/src/lcd/menu/menu.cpp +++ b/Marlin/src/lcd/menu/menu.cpp @@ -268,6 +268,8 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co #if HAS_GRAPHICAL_LCD drawing_screen = false; #endif + + set_ui_selection(false); } } @@ -436,12 +438,21 @@ void _lcd_draw_homing() { void _lcd_toggle_bed_leveling() { set_bed_leveling_enabled(!planner.leveling_active); } #endif -void do_select_screen(PGM_P const yes, PGM_P const no, bool &yesno, PGM_P const pref, const char * const string, PGM_P const suff) { +// +// Selection screen presents a prompt and two options +// +bool ui_selection; // = false +void set_ui_selection(const bool sel) { ui_selection = sel; } +void do_select_screen(PGM_P const yes, PGM_P const no, selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string/*=NULL*/, PGM_P const suff/*=NULL*/) { if (ui.encoderPosition) { - yesno = int16_t(ui.encoderPosition) > 0; + ui_selection = int16_t(ui.encoderPosition) > 0; ui.encoderPosition = 0; } - draw_select_screen(yes, no, yesno, pref, string, suff); + const bool got_click = ui.use_click(); + if (got_click || ui.should_draw()) { + draw_select_screen(yes, no, ui_selection, pref, string, suff); + if (got_click) { ui_selection ? yesFunc() : noFunc(); } + } } #endif // HAS_LCD_MENU diff --git a/Marlin/src/lcd/menu/menu.h b/Marlin/src/lcd/menu/menu.h index acc51a2ae0..de3bd210fb 100644 --- a/Marlin/src/lcd/menu/menu.h +++ b/Marlin/src/lcd/menu/menu.h @@ -65,12 +65,15 @@ DECLARE_MENU_EDIT_TYPE(uint32_t, long5, ftostr5rj, 0.01f ); // 123 ///////// Menu Item Draw Functions ///////// //////////////////////////////////////////// -void draw_edit_screen(PGM_P const pstr, const char* const value=NULL); +typedef void (*selectFunc_t)(); void draw_select_screen(PGM_P const yes, PGM_P const no, const bool yesno, PGM_P const pref, const char * const string, PGM_P const suff); -void do_select_screen(PGM_P const yes, PGM_P const no, bool &yesno, PGM_P const pref, const char * const string=NULL, PGM_P const suff=NULL); -inline void do_select_screen_yn(bool &yesno, PGM_P const pref, const char * const string, PGM_P const suff) { - do_select_screen(PSTR(MSG_YES), PSTR(MSG_NO), yesno, pref, string, suff); +void set_ui_selection(const bool sel); +void do_select_screen(PGM_P const yes, PGM_P const no, selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string=NULL, PGM_P const suff=NULL); +inline void do_select_screen_yn(selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string=NULL, PGM_P const suff=NULL) { + do_select_screen(PSTR(MSG_YES), PSTR(MSG_NO), yesFunc, noFunc, pref, string, suff); } + +void draw_edit_screen(PGM_P const pstr, const char* const value=NULL); void draw_menu_item(const bool sel, const uint8_t row, PGM_P const pstr, const char pre_char, const char post_char); void draw_menu_item_static(const uint8_t row, PGM_P const pstr, const bool center=true, const bool invert=false, const char *valstr=NULL); void _draw_menu_item_edit(const bool sel, const uint8_t row, PGM_P const pstr, const char* const data, const bool pgm); diff --git a/Marlin/src/lcd/menu/menu_advanced.cpp b/Marlin/src/lcd/menu/menu_advanced.cpp index 05396f8507..9d99d03962 100644 --- a/Marlin/src/lcd/menu/menu_advanced.cpp +++ b/Marlin/src/lcd/menu/menu_advanced.cpp @@ -604,16 +604,13 @@ void menu_backlash(); #include "../../module/configuration_store.h" - static void lcd_init_eeprom() { - ui.completion_feedback(settings.init_eeprom()); - ui.goto_previous_screen(); - } - static void lcd_init_eeprom_confirm() { - START_MENU(); - MENU_BACK(MSG_ADVANCED_SETTINGS); - MENU_ITEM(function, MSG_INIT_EEPROM, lcd_init_eeprom); - END_MENU(); + do_select_screen( + PSTR(MSG_BUTTON_INIT), PSTR(MSG_BUTTON_CANCEL), + []{ ui.completion_feedback(settings.init_eeprom()); }, + ui.goto_previous_screen, + PSTR(MSG_INIT_EEPROM), NULL, PSTR("?") + ); } #endif diff --git a/Marlin/src/lcd/menu/menu_bed_corners.cpp b/Marlin/src/lcd/menu/menu_bed_corners.cpp index b36d8dd3b1..de24ed5a56 100644 --- a/Marlin/src/lcd/menu/menu_bed_corners.cpp +++ b/Marlin/src/lcd/menu/menu_bed_corners.cpp @@ -50,13 +50,6 @@ static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Pleas static bool leveling_was_active = false; #endif -static inline void _lcd_level_bed_corners_back() { - #if HAS_LEVELING - set_bed_leveling_enabled(leveling_was_active); - #endif - ui.goto_previous_screen_no_defer(); -} - /** * Level corners, starting in the front-left corner. */ @@ -94,17 +87,23 @@ static inline void _lcd_goto_next_corner() { } static inline void menu_level_bed_corners() { - START_MENU(); - MENU_ITEM(function, - #if ENABLED(LEVEL_CENTER_TOO) - MSG_LEVEL_BED_NEXT_POINT - #else - MSG_NEXT_CORNER - #endif - , _lcd_goto_next_corner + do_select_screen( + PSTR(MSG_BUTTON_NEXT), PSTR(MSG_BUTTON_DONE), + _lcd_goto_next_corner, + []{ + #if HAS_LEVELING + set_bed_leveling_enabled(leveling_was_active); + #endif + ui.goto_previous_screen_no_defer(); + }, + PSTR( + #if ENABLED(LEVEL_CENTER_TOO) + MSG_LEVEL_BED_NEXT_POINT + #else + MSG_NEXT_CORNER + #endif + ), NULL, PSTR("?") ); - MENU_ITEM(function, MSG_BACK, _lcd_level_bed_corners_back); - END_MENU(); } static inline void _lcd_level_bed_corners_homing() { @@ -112,6 +111,7 @@ static inline void _lcd_level_bed_corners_homing() { if (all_axes_homed()) { bed_corner = 0; ui.goto_screen(menu_level_bed_corners); + set_ui_selection(true); _lcd_goto_next_corner(); } } diff --git a/Marlin/src/lcd/menu/menu_job_recovery.cpp b/Marlin/src/lcd/menu/menu_job_recovery.cpp index 6d584948c4..f819052977 100644 --- a/Marlin/src/lcd/menu/menu_job_recovery.cpp +++ b/Marlin/src/lcd/menu/menu_job_recovery.cpp @@ -44,6 +44,8 @@ static void lcd_power_loss_recovery_cancel() { ui.return_to_status(); } +// TODO: Display long filename with Cancel/Resume buttons +// Requires supporting methods in PLR class. void menu_job_recovery() { ui.defer_status_screen(); START_MENU(); diff --git a/Marlin/src/lcd/menu/menu_main.cpp b/Marlin/src/lcd/menu/menu_main.cpp index 325f09b9b4..db9c6c867c 100644 --- a/Marlin/src/lcd/menu/menu_main.cpp +++ b/Marlin/src/lcd/menu/menu_main.cpp @@ -101,10 +101,7 @@ } void menu_abort_confirm() { - START_MENU(); - MENU_BACK(MSG_MAIN); - MENU_ITEM(function, MSG_STOP_PRINT, lcd_abort_job); - END_MENU(); + do_select_screen(PSTR(MSG_BUTTON_STOP), PSTR(MSG_BACK), lcd_abort_job, ui.goto_previous_screen, PSTR(MSG_STOP_PRINT), NULL, PSTR("?")); } #endif // MACHINE_CAN_STOP diff --git a/Marlin/src/lcd/menu/menu_mixer.cpp b/Marlin/src/lcd/menu/menu_mixer.cpp index 8e5b6f4d0f..77124d1146 100644 --- a/Marlin/src/lcd/menu/menu_mixer.cpp +++ b/Marlin/src/lcd/menu/menu_mixer.cpp @@ -250,17 +250,17 @@ void lcd_mixer_mix_edit() { // // Reset All V-Tools // -inline void _lcd_reset_vtools() { - LCD_MESSAGEPGM(MSG_VTOOLS_RESET); - ui.return_to_status(); - mixer.reset_vtools(); -} - void menu_mixer_vtools_reset_confirm() { - START_MENU(); - MENU_BACK(MSG_BACK); - MENU_ITEM(function, MSG_RESET_VTOOLS, _lcd_reset_vtools); - END_MENU(); + do_select_screen( + PSTR(MSG_BUTTON_RESET), PSTR(MSG_BUTTON_CANCEL), + []{ + mixer.reset_vtools(); + LCD_MESSAGEPGM(MSG_VTOOLS_RESET); + ui.return_to_status(); + }, + ui.goto_previous_screen, + PSTR(MSG_RESET_VTOOLS), NULL, PSTR("?") + ); } void menu_mixer() { diff --git a/Marlin/src/lcd/menu/menu_sdcard.cpp b/Marlin/src/lcd/menu/menu_sdcard.cpp index 274643841f..d574dc150e 100644 --- a/Marlin/src/lcd/menu/menu_sdcard.cpp +++ b/Marlin/src/lcd/menu/menu_sdcard.cpp @@ -81,17 +81,12 @@ inline void sdcard_start_selected_file() { #if ENABLED(SD_MENU_CONFIRM_START) - bool do_print_file; void menu_sd_confirm() { - if (ui.should_draw()) - do_select_screen(PSTR(MSG_BUTTON_PRINT), PSTR(MSG_BUTTON_CANCEL), do_print_file, PSTR(MSG_START_PRINT " "), card.longest_filename(), PSTR("?")); - - if (ui.use_click()) { - if (do_print_file) - sdcard_start_selected_file(); - else - ui.goto_previous_screen(); - } + do_select_screen( + PSTR(MSG_BUTTON_PRINT), PSTR(MSG_BUTTON_CANCEL), + sdcard_start_selected_file, ui.goto_previous_screen, + PSTR(MSG_START_PRINT " "), card.longest_filename(), PSTR("?") + ); } #endif @@ -106,7 +101,6 @@ class MenuItem_sdfile { sd_items = screen_items; #endif #if ENABLED(SD_MENU_CONFIRM_START) - do_print_file = false; MenuItem_submenu::action(menu_sd_confirm); #else sdcard_start_selected_file(); diff --git a/Marlin/src/lcd/menu/menu_service.cpp b/Marlin/src/lcd/menu/menu_service.cpp index 05d43f5fd0..3ab890d7bb 100644 --- a/Marlin/src/lcd/menu/menu_service.cpp +++ b/Marlin/src/lcd/menu/menu_service.cpp @@ -31,52 +31,32 @@ #include "menu.h" #include "../../module/printcounter.h" -inline void _lcd_reset_service(const int index) { - print_job_timer.resetServiceInterval(index); - BUZZ(200, 404); - ui.reset_status(); - ui.return_to_status(); +inline void _menu_service(const int index, PGM_P const name) { + char sram[30]; + strncpy_P(sram, name, 29); + do_select_screen( + PSTR(MSG_BUTTON_RESET), PSTR(MSG_BUTTON_CANCEL), + []{ + print_job_timer.resetServiceInterval(index); + ui.completion_feedback(true); + ui.reset_status(); + ui.return_to_status(); + }, + ui.goto_previous_screen, + PSTR(MSG_SERVICE_RESET), sram, PSTR("?") + ); } #if SERVICE_INTERVAL_1 > 0 - void menu_action_reset_service1() { _lcd_reset_service(1); } + void menu_service1() { _menu_service(1, PSTR(SERVICE_NAME_1)); } #endif #if SERVICE_INTERVAL_2 > 0 - void menu_action_reset_service2() { _lcd_reset_service(2); } + void menu_service2() { _menu_service(2, PSTR(SERVICE_NAME_2)); } #endif #if SERVICE_INTERVAL_3 > 0 - void menu_action_reset_service3() { _lcd_reset_service(3); } -#endif - -inline void _menu_service(const int index) { - START_MENU(); - MENU_BACK(MSG_MAIN); - switch (index) { - #if SERVICE_INTERVAL_1 > 0 - case 1: MENU_ITEM(function, MSG_SERVICE_RESET, menu_action_reset_service1); break; - #endif - #if SERVICE_INTERVAL_2 > 0 - case 2: MENU_ITEM(function, MSG_SERVICE_RESET, menu_action_reset_service2); break; - #endif - #if SERVICE_INTERVAL_3 > 0 - case 3: MENU_ITEM(function, MSG_SERVICE_RESET, menu_action_reset_service3); break; - #endif - } - END_MENU(); -} - -#if SERVICE_INTERVAL_1 > 0 - void menu_service1() { _menu_service(1); } -#endif - -#if SERVICE_INTERVAL_2 > 0 - void menu_service2() { _menu_service(2); } -#endif - -#if SERVICE_INTERVAL_3 > 0 - void menu_service3() { _menu_service(3); } + void menu_service3() { _menu_service(3, PSTR(SERVICE_NAME_3)); } #endif #endif // HAS_LCD_MENU && HAS_SERVICE_INTERVALS && PRINTCOUNTER diff --git a/Marlin/src/lcd/menu/menu_tmc.cpp b/Marlin/src/lcd/menu/menu_tmc.cpp index 3d44649599..13634c5894 100644 --- a/Marlin/src/lcd/menu/menu_tmc.cpp +++ b/Marlin/src/lcd/menu/menu_tmc.cpp @@ -32,7 +32,7 @@ #include "../../module/stepper_indirection.h" #include "../../feature/tmc_util.h" -#define TMC_EDIT_STORED_I_RMS(ST) MENU_ITEM_EDIT_CALLBACK(uint16_4, MSG_##ST, &stepper##ST.val_mA, 100, 3000, refresh_stepper_current_##ST) +#define TMC_EDIT_STORED_I_RMS(ST,MSG) MENU_ITEM_EDIT_CALLBACK(uint16_4, MSG, &stepper##ST.val_mA, 100, 3000, refresh_stepper_current_##ST) #if AXIS_IS_TMC(X) void refresh_stepper_current_X() { stepperX.refresh_stepper_current(); } @@ -78,50 +78,50 @@ void menu_tmc_current() { START_MENU(); MENU_BACK(MSG_TMC_DRIVERS); #if AXIS_IS_TMC(X) - TMC_EDIT_STORED_I_RMS(X); + TMC_EDIT_STORED_I_RMS(X, MSG_X); #endif #if AXIS_IS_TMC(Y) - TMC_EDIT_STORED_I_RMS(Y); + TMC_EDIT_STORED_I_RMS(Y, MSG_Y); #endif #if AXIS_IS_TMC(Z) - TMC_EDIT_STORED_I_RMS(Z); + TMC_EDIT_STORED_I_RMS(Z, MSG_Z); #endif #if AXIS_IS_TMC(X2) - TMC_EDIT_STORED_I_RMS(X2); + TMC_EDIT_STORED_I_RMS(X2, MSG_X2); #endif #if AXIS_IS_TMC(Y2) - TMC_EDIT_STORED_I_RMS(Y2); + TMC_EDIT_STORED_I_RMS(Y2, MSG_Y2); #endif #if AXIS_IS_TMC(Z2) - TMC_EDIT_STORED_I_RMS(Z2); + TMC_EDIT_STORED_I_RMS(Z2, MSG_Z2); #endif #if AXIS_IS_TMC(Z3) - TMC_EDIT_STORED_I_RMS(Z3); + TMC_EDIT_STORED_I_RMS(Z3, MSG_Z3); #endif #if AXIS_IS_TMC(E0) - TMC_EDIT_STORED_I_RMS(E0); + TMC_EDIT_STORED_I_RMS(E0, MSG_E1); #endif #if AXIS_IS_TMC(E1) - TMC_EDIT_STORED_I_RMS(E1); + TMC_EDIT_STORED_I_RMS(E1, MSG_E2); #endif #if AXIS_IS_TMC(E2) - TMC_EDIT_STORED_I_RMS(E2); + TMC_EDIT_STORED_I_RMS(E2, MSG_E3); #endif #if AXIS_IS_TMC(E3) - TMC_EDIT_STORED_I_RMS(E3); + TMC_EDIT_STORED_I_RMS(E3, MSG_E4); #endif #if AXIS_IS_TMC(E4) - TMC_EDIT_STORED_I_RMS(E4); + TMC_EDIT_STORED_I_RMS(E4, MSG_E5); #endif #if AXIS_IS_TMC(E5) - TMC_EDIT_STORED_I_RMS(E5); + TMC_EDIT_STORED_I_RMS(E5, MSG_E6); #endif END_MENU(); } #if ENABLED(HYBRID_THRESHOLD) - #define TMC_EDIT_STORED_HYBRID_THRS(ST) MENU_ITEM_EDIT_CALLBACK(uint8, MSG_##ST, &stepper##ST.stored.hybrid_thrs, 0, 255, refresh_hybrid_thrs_##ST); + #define TMC_EDIT_STORED_HYBRID_THRS(ST, MSG) MENU_ITEM_EDIT_CALLBACK(uint8, MSG, &stepper##ST.stored.hybrid_thrs, 0, 255, refresh_hybrid_thrs_##ST); #if AXIS_HAS_STEALTHCHOP(X) void refresh_hybrid_thrs_X() { stepperX.refresh_hybrid_thrs(planner.settings.axis_steps_per_mm[X_AXIS]); } @@ -167,43 +167,43 @@ void menu_tmc_current() { START_MENU(); MENU_BACK(MSG_TMC_DRIVERS); #if AXIS_HAS_STEALTHCHOP(X) - TMC_EDIT_STORED_HYBRID_THRS(X); + TMC_EDIT_STORED_HYBRID_THRS(X, MSG_X); #endif #if AXIS_HAS_STEALTHCHOP(Y) - TMC_EDIT_STORED_HYBRID_THRS(Y); + TMC_EDIT_STORED_HYBRID_THRS(Y, MSG_Y); #endif #if AXIS_HAS_STEALTHCHOP(Z) - TMC_EDIT_STORED_HYBRID_THRS(Z); + TMC_EDIT_STORED_HYBRID_THRS(Z, MSG_Z); #endif #if AXIS_HAS_STEALTHCHOP(X2) - TMC_EDIT_STORED_HYBRID_THRS(X2); + TMC_EDIT_STORED_HYBRID_THRS(X2, MSG_X2); #endif #if AXIS_HAS_STEALTHCHOP(Y2) - TMC_EDIT_STORED_HYBRID_THRS(Y2); + TMC_EDIT_STORED_HYBRID_THRS(Y2, MSG_Y2); #endif #if AXIS_HAS_STEALTHCHOP(Z2) - TMC_EDIT_STORED_HYBRID_THRS(Z2); + TMC_EDIT_STORED_HYBRID_THRS(Z2, MSG_Z2); #endif #if AXIS_HAS_STEALTHCHOP(Z3) - TMC_EDIT_STORED_HYBRID_THRS(Z3); + TMC_EDIT_STORED_HYBRID_THRS(Z3, MSG_Z3); #endif #if AXIS_HAS_STEALTHCHOP(E0) - TMC_EDIT_STORED_HYBRID_THRS(E0); + TMC_EDIT_STORED_HYBRID_THRS(E0, MSG_E1); #endif #if AXIS_HAS_STEALTHCHOP(E1) - TMC_EDIT_STORED_HYBRID_THRS(E1); + TMC_EDIT_STORED_HYBRID_THRS(E1, MSG_E2); #endif #if AXIS_HAS_STEALTHCHOP(E2) - TMC_EDIT_STORED_HYBRID_THRS(E2); + TMC_EDIT_STORED_HYBRID_THRS(E2, MSG_E3); #endif #if AXIS_HAS_STEALTHCHOP(E3) - TMC_EDIT_STORED_HYBRID_THRS(E3); + TMC_EDIT_STORED_HYBRID_THRS(E3, MSG_E4); #endif #if AXIS_HAS_STEALTHCHOP(E4) - TMC_EDIT_STORED_HYBRID_THRS(E4); + TMC_EDIT_STORED_HYBRID_THRS(E4, MSG_E5); #endif #if AXIS_HAS_STEALTHCHOP(E5) - TMC_EDIT_STORED_HYBRID_THRS(E5); + TMC_EDIT_STORED_HYBRID_THRS(E5, MSG_E6); #endif END_MENU(); } @@ -243,7 +243,7 @@ void menu_tmc_current() { #if HAS_STEALTHCHOP - #define TMC_EDIT_STEP_MODE(ST) MENU_ITEM_EDIT_CALLBACK(bool, MSG_##ST, &stepper##ST.stored.stealthChop_enabled, refresh_stepping_mode_##ST) + #define TMC_EDIT_STEP_MODE(ST, MSG) MENU_ITEM_EDIT_CALLBACK(bool, MSG, &stepper##ST.stored.stealthChop_enabled, refresh_stepping_mode_##ST) #if AXIS_HAS_STEALTHCHOP(X) void refresh_stepping_mode_X() { stepperX.refresh_stepping_mode(); } @@ -290,43 +290,43 @@ void menu_tmc_current() { STATIC_ITEM(MSG_TMC_STEALTH_ENABLED); MENU_BACK(MSG_TMC_DRIVERS); #if AXIS_HAS_STEALTHCHOP(X) - TMC_EDIT_STEP_MODE(X); + TMC_EDIT_STEP_MODE(X, MSG_X); #endif #if AXIS_HAS_STEALTHCHOP(Y) - TMC_EDIT_STEP_MODE(Y); + TMC_EDIT_STEP_MODE(Y, MSG_Y); #endif #if AXIS_HAS_STEALTHCHOP(Z) - TMC_EDIT_STEP_MODE(Z); + TMC_EDIT_STEP_MODE(Z, MSG_Z); #endif #if AXIS_HAS_STEALTHCHOP(X2) - TMC_EDIT_STEP_MODE(X2); + TMC_EDIT_STEP_MODE(X2, MSG_X2); #endif #if AXIS_HAS_STEALTHCHOP(Y2) - TMC_EDIT_STEP_MODE(Y2); + TMC_EDIT_STEP_MODE(Y2, MSG_Y2); #endif #if AXIS_HAS_STEALTHCHOP(Z2) - TMC_EDIT_STEP_MODE(Z2); + TMC_EDIT_STEP_MODE(Z2, MSG_Z2); #endif #if AXIS_HAS_STEALTHCHOP(Z3) - TMC_EDIT_STEP_MODE(Z3); + TMC_EDIT_STEP_MODE(Z3, MSG_Z3); #endif #if AXIS_HAS_STEALTHCHOP(E0) - TMC_EDIT_STEP_MODE(E0); + TMC_EDIT_STEP_MODE(E0, MSG_E1); #endif #if AXIS_HAS_STEALTHCHOP(E1) - TMC_EDIT_STEP_MODE(E1); + TMC_EDIT_STEP_MODE(E1, MSG_E2); #endif #if AXIS_HAS_STEALTHCHOP(E2) - TMC_EDIT_STEP_MODE(E2); + TMC_EDIT_STEP_MODE(E2, MSG_E3); #endif #if AXIS_HAS_STEALTHCHOP(E3) - TMC_EDIT_STEP_MODE(E3); + TMC_EDIT_STEP_MODE(E3, MSG_E4); #endif #if AXIS_HAS_STEALTHCHOP(E4) - TMC_EDIT_STEP_MODE(E4); + TMC_EDIT_STEP_MODE(E4, MSG_E5); #endif #if AXIS_HAS_STEALTHCHOP(E5) - TMC_EDIT_STEP_MODE(E5); + TMC_EDIT_STEP_MODE(E5, MSG_E6); #endif END_MENU(); } diff --git a/Marlin/src/lcd/menu/menu_ubl.cpp b/Marlin/src/lcd/menu/menu_ubl.cpp index 9b7a5b5fa6..8b182b89b9 100644 --- a/Marlin/src/lcd/menu/menu_ubl.cpp +++ b/Marlin/src/lcd/menu/menu_ubl.cpp @@ -615,8 +615,10 @@ void _lcd_ubl_step_by_step() { void _lcd_ubl_level_bed() { START_MENU(); MENU_BACK(MSG_MOTION); - MENU_ITEM(gcode, MSG_UBL_ACTIVATE_MESH, PSTR("G29 A")); - MENU_ITEM(gcode, MSG_UBL_DEACTIVATE_MESH, PSTR("G29 D")); + if (planner.leveling_active) + MENU_ITEM(gcode, MSG_UBL_DEACTIVATE_MESH, PSTR("G29 D")); + else + MENU_ITEM(gcode, MSG_UBL_ACTIVATE_MESH, PSTR("G29 A")); MENU_ITEM(submenu, MSG_UBL_STEP_BY_STEP_MENU, _lcd_ubl_step_by_step); MENU_ITEM(function, MSG_UBL_MESH_EDIT, _lcd_ubl_output_map_lcd_cmd); MENU_ITEM(submenu, MSG_UBL_STORAGE_MESH_MENU, _lcd_ubl_storage_mesh); diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp index cb8b308df3..0d4b88d2c3 100644 --- a/Marlin/src/lcd/ultralcd.cpp +++ b/Marlin/src/lcd/ultralcd.cpp @@ -192,24 +192,39 @@ millis_t next_button_update_ms; #endif - void wrap_string(uint8_t y, const char * const string) { - uint8_t x = LCD_WIDTH; + void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte) { + SETCURSOR(x, y); if (string) { uint8_t *p = (uint8_t*)string; for (;;) { - if (x >= LCD_WIDTH) { - x = 0; - SETCURSOR(0, y++); - } wchar_t ch; - p = get_utf8_value_cb(p, read_byte_ram, &ch); + p = get_utf8_value_cb(p, cb_read_byte, &ch); if (!ch) break; lcd_put_wchar(ch); x++; + if (x >= LCD_WIDTH) { + x = 0; y++; + SETCURSOR(0, y); + } } } } + void MarlinUI::draw_select_screen_prompt(PGM_P const pref, const char * const string/*=NULL*/, PGM_P const suff/*=NULL*/) { + const uint8_t plen = utf8_strlen_P(pref), slen = suff ? utf8_strlen_P(suff) : 0; + uint8_t x = 0, y = 0; + if (!string && plen + slen <= LCD_WIDTH) { + x = (LCD_WIDTH - plen - slen) / 2; + y = LCD_HEIGHT > 3 ? 1 : 0; + } + wrap_string_P(x, y, pref); + if (string) { + if (x) { x = 0; y++; } // Move to the start of the next line + wrap_string(x, y, string); + } + if (suff) wrap_string_P(x, y, suff); + } + #endif // HAS_LCD_MENU void MarlinUI::init() { @@ -668,6 +683,7 @@ void MarlinUI::update() { static uint16_t max_display_update_time = 0; static millis_t next_lcd_update_ms; + millis_t ms = millis(); #if HAS_LCD_MENU @@ -729,11 +745,12 @@ void MarlinUI::update() { refresh(); init_lcd(); // May revive the LCD if static electricity killed it + ms = millis(); + next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL; // delay LCD update until after SD activity completes } #endif // SDSUPPORT && SD_DETECT_PIN - const millis_t ms = millis(); if (ELAPSED(ms, next_lcd_update_ms) #if HAS_GRAPHICAL_LCD || drawing_screen diff --git a/Marlin/src/lcd/ultralcd.h b/Marlin/src/lcd/ultralcd.h index be694ddfe4..2ea7f45279 100644 --- a/Marlin/src/lcd/ultralcd.h +++ b/Marlin/src/lcd/ultralcd.h @@ -72,7 +72,11 @@ #define LCDWRITE(c) lcd_put_wchar(c) #endif - void wrap_string(uint8_t y, const char * const string); + #include "fontutils.h" + + void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte); + inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr) { _wrap_string(x, y, pstr, read_byte_rom); } + inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string) { _wrap_string(x, y, string, read_byte_ram); } #if ENABLED(SDSUPPORT) #include "../sd/cardreader.h" @@ -457,6 +461,8 @@ public: static void ubl_plot(const uint8_t x, const uint8_t inverted_y); #endif + static void draw_select_screen_prompt(PGM_P const pref, const char * const string=NULL, PGM_P const suff=NULL); + #elif HAS_SPI_LCD static constexpr bool lcd_clicked = false; diff --git a/Marlin/src/module/configuration_store.cpp b/Marlin/src/module/configuration_store.cpp index 0552f555a5..a766d91b6e 100644 --- a/Marlin/src/module/configuration_store.cpp +++ b/Marlin/src/module/configuration_store.cpp @@ -64,6 +64,10 @@ #include "../feature/bedlevel/bedlevel.h" #endif +#if ENABLED(EXTENSIBLE_UI) + #include "../lcd/extensible_ui/ui_api.h" +#endif + #if HAS_SERVOS #include "servo.h" #endif @@ -1120,6 +1124,10 @@ void MarlinSettings::postprocess() { store_mesh(ubl.storage_slot); #endif + #if ENABLED(EXTENSIBLE_UI) + if (!eeprom_error) ExtUI::onStoreSettings(); + #endif + return !eeprom_error; } @@ -1874,7 +1882,13 @@ void MarlinSettings::postprocess() { } bool MarlinSettings::load() { - if (validate()) return _load(); + if (validate()) { + const bool success = _load(); + #if ENABLED(EXTENSIBLE_UI) + if (success) ExtUI::onLoadSettings(); + #endif + return success; + } reset(); return true; } @@ -2290,6 +2304,10 @@ void MarlinSettings::reset() { DEBUG_ECHO_START(); DEBUG_ECHOLNPGM("Hardcoded Default Settings Loaded"); + + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onFactoryReset(); + #endif } #if DISABLED(DISABLE_M503) diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 8f3361944d..25a45661aa 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -86,17 +86,17 @@ Temperature thermalManager; */ #if HAS_HEATED_BED - #define _BED_PSTR(E) (E) == -1 ? PSTR(MSG ## _BED) : + #define _BED_PSTR(M,E) (E) == -1 ? PSTR(M) : #else - #define _BED_PSTR(E) + #define _BED_PSTR(M,E) #endif #if HAS_HEATED_CHAMBER - #define _CHAMBER_PSTR(E) (E) == -2 ? PSTR(MSG ## _CHAMBER) : + #define _CHAMBER_PSTR(M,E) (E) == -2 ? PSTR(M) : #else - #define _CHAMBER_PSTR(E) + #define _CHAMBER_PSTR(M,E) #endif -#define _E_PSTR(M,E,N) (HOTENDS >= (N) && (E) == (N)-1) ? PSTR(MSG_E##N " " M) : -#define TEMP_ERR_PSTR(M,E) _BED_PSTR(E) _CHAMBER_PSTR(E) _E_PSTR(M,E,2) _E_PSTR(M,E,3) _E_PSTR(M,E,4) _E_PSTR(M,E,5) _E_PSTR(M,E,6) PSTR(MSG_E1 " " M) +#define _E_PSTR(M,E,N) ((HOTENDS) >= (N) && (E) == (N)-1) ? PSTR(MSG_E##N " " M) : +#define TEMP_ERR_PSTR(M,E) _BED_PSTR(M##_BED,E) _CHAMBER_PSTR(M##_CHAMBER,E) _E_PSTR(M,E,2) _E_PSTR(M,E,3) _E_PSTR(M,E,4) _E_PSTR(M,E,5) _E_PSTR(M,E,6) PSTR(MSG_E1 " " M) // public: @@ -944,11 +944,29 @@ void Temperature::manage_heater() { if (temp_hotend[1].current < MAX(HEATER_1_MINTEMP, HEATER_1_MAX6675_TMIN + .01)) min_temp_error(1); #endif - #if WATCH_HOTENDS || WATCH_BED || DISABLED(PIDTEMPBED) || HAS_AUTO_FAN || HEATER_IDLE_HANDLER || WATCH_CHAMBER + #define HAS_THERMAL_PROTECTION (ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER)) + + #if HAS_THERMAL_PROTECTION || DISABLED(PIDTEMPBED) || HAS_AUTO_FAN || HEATER_IDLE_HANDLER millis_t ms = millis(); #endif + #if HAS_THERMAL_PROTECTION + #ifndef THERMAL_PROTECTION_GRACE_PERIOD + #define THERMAL_PROTECTION_GRACE_PERIOD 0 // No grace period needed on well-behaved boards + #endif + #if THERMAL_PROTECTION_GRACE_PERIOD > 0 + static millis_t grace_period = ms + THERMAL_PROTECTION_GRACE_PERIOD; + if (ELAPSED(ms, grace_period)) grace_period = 0UL; + #else + static constexpr millis_t grace_period = 0UL; + #endif + #endif + HOTEND_LOOP() { + #if ENABLED(THERMAL_PROTECTION_HOTENDS) + if (!grace_period && degHotend(e) > temp_range[e].maxtemp) + _temp_error(e, PSTR(MSG_T_THERMAL_RUNAWAY), TEMP_ERR_PSTR(MSG_THERMAL_RUNAWAY, e)); + #endif #if HEATER_IDLE_HANDLER hotend_idle[e].update(ms); @@ -1001,6 +1019,11 @@ void Temperature::manage_heater() { #if HAS_HEATED_BED + #if ENABLED(THERMAL_PROTECTION_BED) + if (!grace_period && degBed() > BED_MAXTEMP) + _temp_error(-1, PSTR(MSG_T_THERMAL_RUNAWAY), TEMP_ERR_PSTR(MSG_THERMAL_RUNAWAY, -1)); + #endif + #if WATCH_BED // Make sure temperature is increasing if (watch_bed.elapsed(ms)) { // Time to check the bed? @@ -1071,6 +1094,11 @@ void Temperature::manage_heater() { #if HAS_HEATED_CHAMBER + #if ENABLED(THERMAL_PROTECTION_CHAMBER) + if (!grace_period && degChamber() > CHAMBER_MAXTEMP) + _temp_error(-2, PSTR(MSG_T_THERMAL_RUNAWAY), TEMP_ERR_PSTR(MSG_THERMAL_RUNAWAY, -2)); + #endif + #if WATCH_CHAMBER // Make sure temperature is increasing if (watch_chamber.elapsed(ms)) { // Time to check the chamber? @@ -1602,7 +1630,7 @@ void Temperature::init() { } #endif -#if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER) +#if HAS_THERMAL_PROTECTION #if ENABLED(THERMAL_PROTECTION_HOTENDS) Temperature::tr_state_machine_t Temperature::tr_state_machine[HOTENDS]; // = { { TRInactive, 0 } }; @@ -1619,17 +1647,17 @@ void Temperature::init() { static float tr_target_temperature[HOTENDS + 1] = { 0.0 }; /** - SERIAL_ECHO_START(); - SERIAL_ECHOPGM("Thermal Thermal Runaway Running. Heater ID: "); - if (heater_id == -2) SERIAL_ECHOPGM("chamber"); - if (heater_id < 0) SERIAL_ECHOPGM("bed"); else SERIAL_ECHO(heater_id); - SERIAL_ECHOPAIR(" ; State:", sm.state, " ; Timer:", sm.timer, " ; Temperature:", current, " ; Target Temp:", target); - if (heater_id >= 0) - SERIAL_ECHOPAIR(" ; Idle Timeout:", hotend_idle[heater_id].timed_out); - else - SERIAL_ECHOPAIR(" ; Idle Timeout:", bed_idle.timed_out); - SERIAL_EOL(); - */ + SERIAL_ECHO_START(); + SERIAL_ECHOPGM("Thermal Thermal Runaway Running. Heater ID: "); + if (heater_id == -2) SERIAL_ECHOPGM("chamber"); + if (heater_id < 0) SERIAL_ECHOPGM("bed"); else SERIAL_ECHO(heater_id); + SERIAL_ECHOPAIR(" ; State:", sm.state, " ; Timer:", sm.timer, " ; Temperature:", current, " ; Target Temp:", target); + if (heater_id >= 0) + SERIAL_ECHOPAIR(" ; Idle Timeout:", hotend_idle[heater_id].timed_out); + else + SERIAL_ECHOPAIR(" ; Idle Timeout:", bed_idle.timed_out); + SERIAL_EOL(); + //*/ const int heater_index = heater_id >= 0 ? heater_id : HOTENDS; @@ -2647,7 +2675,7 @@ void Temperature::isr() { void Temperature::set_heating_message(const uint8_t e) { const bool heating = isHeatingHotend(e); #if HOTENDS > 1 - ui.status_printf_P(0, heating ? PSTR("E%i " MSG_HEATING) : PSTR("E%i " MSG_COOLING), int(e + 1)); + ui.status_printf_P(0, heating ? PSTR("E%c " MSG_HEATING) : PSTR("E%c " MSG_COOLING), '1' + e); #else ui.set_status_P(heating ? PSTR("E " MSG_HEATING) : PSTR("E " MSG_COOLING)); #endif diff --git a/Marlin/src/module/tool_change.cpp b/Marlin/src/module/tool_change.cpp index 9108a23ab4..3b97cb60c1 100644 --- a/Marlin/src/module/tool_change.cpp +++ b/Marlin/src/module/tool_change.cpp @@ -280,47 +280,37 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { grabpos = parkingposx[tmp_extruder] + (tmp_extruder ? PARKING_EXTRUDER_GRAB_DISTANCE : -(PARKING_EXTRUDER_GRAB_DISTANCE)) + x_offset; /** - * 1. Raise Z-Axis to give enough clearance - * 2. Move to park position of old extruder - * 3. Disengage magnetic field, wait for delay - * 4. Move near new extruder - * 5. Engage magnetic field for new extruder - * 6. Move to parking incl. offset of new extruder - * 7. Lower Z-Axis + * 1. Move to park position of old extruder + * 2. Disengage magnetic field, wait for delay + * 3. Move near new extruder + * 4. Engage magnetic field for new extruder + * 5. Move to parking incl. offset of new extruder + * 6. Lower Z-Axis */ // STEP 1 if (DEBUGGING(LEVELING)) DEBUG_POS("Start Autopark", current_position); - current_position[Z_AXIS] += toolchange_settings.z_raise; - - if (DEBUGGING(LEVELING)) DEBUG_POS("(1) Raise Z-Axis", current_position); - - fast_line_to_current(Z_AXIS); - planner.synchronize(); - - // STEP 2 - current_position[X_AXIS] = parkingposx[active_extruder] + x_offset; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOLNPAIR("(2) Park extruder ", int(active_extruder)); + DEBUG_ECHOLNPAIR("(1) Park extruder ", int(active_extruder)); DEBUG_POS("Moving ParkPos", current_position); } fast_line_to_current(X_AXIS); planner.synchronize(); - // STEP 3 + // STEP 2 - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Disengage magnet "); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(2) Disengage magnet "); pe_deactivate_solenoid(active_extruder); - // STEP 4 + // STEP 3 - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Move to position near new extruder"); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Move to position near new extruder"); current_position[X_AXIS] += active_extruder ? -10 : 10; // move 10mm away from parked extruder @@ -329,8 +319,8 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { fast_line_to_current(X_AXIS); planner.synchronize(); - // STEP 5 - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(5) Engage magnetic field"); + // STEP 4 + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Engage magnetic field"); #if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT) pe_activate_solenoid(active_extruder); //just save power for inverted magnets @@ -338,16 +328,16 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { pe_activate_solenoid(tmp_extruder); - // STEP 6 + // STEP 5 current_position[X_AXIS] = grabpos + (tmp_extruder ? -10 : 10); fast_line_to_current(X_AXIS); current_position[X_AXIS] = grabpos; - if (DEBUGGING(LEVELING)) DEBUG_POS("(6) Unpark extruder", current_position); + if (DEBUGGING(LEVELING)) DEBUG_POS("(5) Unpark extruder", current_position); planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS] * 0.5, active_extruder); planner.synchronize(); - // STEP 7 + // STEP 6 current_position[X_AXIS] = midpos #if HAS_HOTEND_OFFSET @@ -355,7 +345,7 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { #endif ; - if (DEBUGGING(LEVELING)) DEBUG_POS("(7) Move midway between hotends", current_position); + if (DEBUGGING(LEVELING)) DEBUG_POS("(6) Move midway between hotends", current_position); fast_line_to_current(X_AXIS); planner.synchronize(); @@ -385,30 +375,20 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { grabxpos = toolheadposx[tmp_extruder]; /** - * 1. Raise Z to give enough clearance - * 2. Move to switch position of current toolhead - * 3. Unlock tool and drop it in the dock - * 4. Move to the new toolhead - * 5. Grab and lock the new toolhead + * 1. Move to switch position of current toolhead + * 2. Unlock tool and drop it in the dock + * 3. Move to the new toolhead + * 4. Grab and lock the new toolhead */ - // 1. Raise Z to give enough clearance + // 1. Move to switch position of current toolhead if (DEBUGGING(LEVELING)) DEBUG_POS("Starting Toolhead change", current_position); - current_position[Z_AXIS] += toolchange_settings.z_raise; - - if (DEBUGGING(LEVELING)) DEBUG_POS("(1) Raise Z-Axis", current_position); - - fast_line_to_current(Z_AXIS); - planner.synchronize(); - - // 2. Move to switch position of current toolhead - current_position[X_AXIS] = placexpos; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOLNPAIR("(2) Place old tool ", int(active_extruder)); + DEBUG_ECHOLNPAIR("(1) Place old tool ", int(active_extruder)); DEBUG_POS("Move X SwitchPos", current_position); } @@ -422,9 +402,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { fast_line_to_current(Y_AXIS); planner.synchronize(); - // 3. Unlock tool and drop it in the dock + // 2. Unlock tool and drop it in the dock - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Unlock and Place Toolhead"); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(2) Unlock and Place Toolhead"); MOVE_SERVO(SWITCHING_TOOLHEAD_SERVO_NR, angles[1]); safe_delay(500); @@ -443,9 +423,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { fast_line_to_current(Y_AXIS); // move away from docked toolhead planner.synchronize(); - // 4. Move to the new toolhead + // 3. Move to the new toolhead - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Move to new toolhead position"); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Move to new toolhead position"); current_position[X_AXIS] = grabxpos; @@ -460,9 +440,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { fast_line_to_current(Y_AXIS); planner.synchronize(); - // 5. Grab and lock the new toolhead + // 4. Grab and lock the new toolhead - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(5) Grab and lock new toolhead "); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Grab and lock new toolhead "); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS; @@ -497,30 +477,20 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { grabxpos = toolheadposx[tmp_extruder]; /** - * 1. Raise Z to give enough clearance - * 2. Move to switch position of current toolhead - * 3. Release and place toolhead in the dock - * 4. Move to the new toolhead - * 5. Grab the new toolhead and move to security position + * 1. Move to switch position of current toolhead + * 2. Release and place toolhead in the dock + * 3. Move to the new toolhead + * 4. Grab the new toolhead and move to security position */ if (DEBUGGING(LEVELING)) DEBUG_POS("Starting Toolhead change", current_position); - // 1. Raise Z to give enough clearance - - current_position[Z_AXIS] += toolchange_settings.z_raise; - - if (DEBUGGING(LEVELING)) DEBUG_POS("(1) Raise Z-Axis", current_position); - - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Z_AXIS], active_extruder); - planner.synchronize(); - - // 2. Move to switch position current toolhead + // 1. Move to switch position current toolhead current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_CLEAR; if (DEBUGGING(LEVELING)) { - SERIAL_ECHOLNPAIR("(2) Place old tool ", int(active_extruder)); + SERIAL_ECHOLNPAIR("(1) Place old tool ", int(active_extruder)); DEBUG_POS("Move Y SwitchPos + Security", current_position); } @@ -548,9 +518,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[X_AXIS] * 0.25), active_extruder); planner.synchronize(); - // 3. Release and place toolhead in the dock + // 2. Release and place toolhead in the dock - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(3) Release and Place Toolhead"); + if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(2) Release and Place Toolhead"); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_RELEASE; @@ -566,9 +536,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[Y_AXIS]), active_extruder); planner.synchronize(); - // 4. Move to new toolhead position + // 3. Move to new toolhead position - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(4) Move to new toolhead position"); + if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(3) Move to new toolhead position"); current_position[X_AXIS] = grabxpos; @@ -577,9 +547,9 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); planner.synchronize(); - // 5. Grab the new toolhead and move to security position + // 4. Grab the new toolhead and move to security position - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(5) Grab new toolhead and move to security position"); + if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(4) Grab new toolhead and move to security position"); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_RELEASE; @@ -732,7 +702,11 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n if (tmp_extruder >= EXTRUDERS) return invalid_extruder_error(tmp_extruder); - if (!no_move && !all_axes_homed()) { + if (!no_move && (!all_axes_homed() + #if ENABLED(DUAL_X_CARRIAGE) + || dual_x_carriage_mode == DXC_FULL_CONTROL_MODE + #endif + )) { no_move = true; if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("No move on toolchange"); } @@ -785,14 +759,15 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n if (!no_move) { #if DISABLED(SWITCHING_NOZZLE) // Do a small lift to avoid the workpiece in the move back (below) - #if ENABLED(TOOLCHANGE_PARK) - current_position[X_AXIS] = toolchange_settings.change_point.x; - current_position[Y_AXIS] = toolchange_settings.change_point.y; - #endif current_position[Z_AXIS] += toolchange_settings.z_raise; #if HAS_SOFTWARE_ENDSTOPS NOMORE(current_position[Z_AXIS], soft_endstop[Z_AXIS].max); #endif + fast_line_to_current(Z_AXIS); + #if ENABLED(TOOLCHANGE_PARK) + current_position[X_AXIS] = toolchange_settings.change_point.x; + current_position[Y_AXIS] = toolchange_settings.change_point.y; + #endif planner.buffer_line(current_position, feedrate_mm_s, active_extruder); #endif planner.synchronize(); @@ -875,10 +850,10 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) if (should_swap && !too_cold) { #if ENABLED(ADVANCED_PAUSE_FEATURE) - do_pause_e_move(toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME, toolchange_settings.prime_speed); + do_pause_e_move(toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME, MMM_TO_MMS(toolchange_settings.prime_speed)); #else current_position[E_AXIS] += (toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME) / planner.e_factor[tmp_extruder]; - planner.buffer_line(current_position, toolchange_settings.prime_speed, tmp_extruder); + planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.prime_speed), tmp_extruder); #endif planner.synchronize(); diff --git a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h b/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h index 92f7dddfaa..319c56f31f 100644 --- a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h +++ b/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h @@ -190,28 +190,70 @@ #define LCD_PINS_D4 P1_21 #else - #define LCD_PINS_RS P1_19 #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 - #define SD_DETECT_PIN P1_31 // (49) (NOT 5V tolerant) - - #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 #define LCD_PINS_ENABLE P1_18 #define LCD_PINS_D4 P1_20 - #if ENABLED(ULTIPANEL) - #define LCD_PINS_D5 P1_21 - #define LCD_PINS_D6 P1_22 - #define LCD_PINS_D7 P1_23 - #endif + #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 + #define SD_DETECT_PIN P1_31 // (49) (NOT 5V tolerant) - #if ENABLED(MKS_MINI_12864) - #define DOGLCD_CS P1_21 - #define DOGLCD_A0 P1_22 - #endif + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS P1_18 + #define DOGLCD_A0 P1_19 + + #define LCD_BACKLIGHT_PIN -1 + + #define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P1_21 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_22 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_23 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN P1_21 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + + #else // !FYSETC_MINI_12864 + + #if ENABLED(MKS_MINI_12864) + #define DOGLCD_CS P1_21 + #define DOGLCD_A0 P1_22 + #endif + + #if ENABLED(ULTIPANEL) + #define LCD_PINS_D5 P1_21 + #define LCD_PINS_D6 P1_22 + #define LCD_PINS_D7 P1_23 + #endif + + #endif // !FYSETC_MINI_12864 #endif diff --git a/Marlin/src/pins/pins_ESP32.h b/Marlin/src/pins/pins_ESP32.h index 343f3841a6..9901dde200 100644 --- a/Marlin/src/pins/pins_ESP32.h +++ b/Marlin/src/pins/pins_ESP32.h @@ -72,3 +72,6 @@ #define HEATER_0_PIN 2 #define FAN_PIN 13 #define HEATER_BED_PIN 4 + +// SPI +#define SDSS 5 diff --git a/Marlin/src/pins/pins_FORMBOT_RAPTOR.h b/Marlin/src/pins/pins_FORMBOT_RAPTOR.h index 5944be04af..10a517aec4 100644 --- a/Marlin/src/pins/pins_FORMBOT_RAPTOR.h +++ b/Marlin/src/pins/pins_FORMBOT_RAPTOR.h @@ -181,16 +181,16 @@ // Formbot only supports REPRAP_DISCOUNT_SMART_CONTROLLER // #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) - #define LCD_PINS_RS 16 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 #define BEEPER_PIN 37 #define BTN_EN1 31 #define BTN_EN2 33 #define BTN_ENC 35 #define SD_DETECT_PIN 49 #define KILL_PIN 41 + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 #endif diff --git a/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h b/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h index 5970123e1f..16649e42b5 100644 --- a/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h +++ b/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h @@ -155,9 +155,8 @@ // // Misc. Functions // -#define CASE_LIGHT_PIN 8 #define SDSS 53 -#ifndef ROXYs_TRex +#ifndef LED_PIN #define LED_PIN 13 // The Formbot v 1 board has almost no unassigned pins on it. The Board's LED #endif // is a good place to get a signal to control the Max7219 LED Matrix. @@ -168,24 +167,28 @@ #define PS_ON_PIN 12 #endif +#define CASE_LIGHT_PIN 8 + // // LCD / Controller // // Formbot only supports REPRAP_DISCOUNT_SMART_CONTROLLER // #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + #ifndef BEEPER_PIN + #define BEEPER_PIN 37 + #endif + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + #define SD_DETECT_PIN 49 + #ifndef KILL_PIN + #define KILL_PIN 41 + #endif #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 23 #define LCD_PINS_D5 25 #define LCD_PINS_D6 27 #define LCD_PINS_D7 29 - #define BTN_EN1 31 - #define BTN_EN2 33 - #define BTN_ENC 35 - #define SD_DETECT_PIN 49 - #ifndef ROXYs_TRex - #define KILL_PIN 41 - #define BEEPER_PIN 37 - #endif #endif diff --git a/Marlin/src/pins/pins_FORMBOT_TREX3.h b/Marlin/src/pins/pins_FORMBOT_TREX3.h index 5b4bd8b533..8ff09f47c5 100644 --- a/Marlin/src/pins/pins_FORMBOT_TREX3.h +++ b/Marlin/src/pins/pins_FORMBOT_TREX3.h @@ -139,7 +139,7 @@ // #define CASE_LIGHT_PIN 5 #define SDSS 53 -#ifndef ROXYs_TRex +#ifndef LED_PIN #define LED_PIN 13 #endif @@ -165,8 +165,10 @@ #define BTN_EN2 33 #define BTN_ENC 35 #define SD_DETECT_PIN 49 - #ifndef ROXYs_TRex + #ifndef KILL_PIN #define KILL_PIN 41 + #endif + #ifndef BEEPER_PIN #define BEEPER_PIN 37 #endif #endif diff --git a/Marlin/src/pins/pins_FYSETC_F6_13.h b/Marlin/src/pins/pins_FYSETC_F6_13.h index e725583008..d40abd1024 100644 --- a/Marlin/src/pins/pins_FYSETC_F6_13.h +++ b/Marlin/src/pins/pins_FYSETC_F6_13.h @@ -28,8 +28,8 @@ #error "Oops! Select 'FYSETC F6' in 'Tools > Board.'" #endif -#ifdef SD_DETECT_INVERTED - #error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board." +#if ENABLED(SD_DETECT_INVERTED) + //#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board." #endif #define BOARD_NAME "FYSETC F6 1.3" @@ -184,25 +184,46 @@ #define BEEPER_PIN 37 #define SD_DETECT_PIN 49 -#if ENABLED(MKS_MINI_12864) - #define DOGLCD_A0 27 - #define DOGLCD_CS 25 -#endif - #if ENABLED(FYSETC_MINI_12864) // // See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 // #define DOGLCD_A0 16 #define DOGLCD_CS 17 - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN 25 + + #define LCD_BACKLIGHT_PIN -1 + #define KILL_PIN 41 + + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN 27 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN 29 + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" #endif #elif HAS_GRAPHICAL_LCD @@ -214,6 +235,11 @@ #define LCD_PINS_D6 27 #define LCD_PINS_D7 29 + #if ENABLED(MKS_MINI_12864) + #define DOGLCD_CS 25 + #define DOGLCD_A0 27 + #endif + #endif #if ENABLED(NEWPANEL) @@ -222,20 +248,6 @@ #define BTN_ENC 35 #endif -#if ENABLED(FYSETC_MINI_12864) - #define LCD_BACKLIGHT_PIN -1 - #define LCD_RESET_PIN 23 - #define KILL_PIN 41 - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN 25 - #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN 27 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN 29 - #endif -#endif #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN 3 #endif diff --git a/Marlin/src/pins/pins_GEN7_13.h b/Marlin/src/pins/pins_GEN7_13.h index 60c62bdc71..9b1f0d242e 100644 --- a/Marlin/src/pins/pins_GEN7_13.h +++ b/Marlin/src/pins/pins_GEN7_13.h @@ -24,7 +24,7 @@ * Gen7 v1.3 pin assignments */ - /** +/** * Rev B 26 DEC 2016 * * added pointer to a current Arduino IDE extension diff --git a/Marlin/src/pins/pins_RAMPS.h b/Marlin/src/pins/pins_RAMPS.h index 40d3dd11e2..120748eeb3 100644 --- a/Marlin/src/pins/pins_RAMPS.h +++ b/Marlin/src/pins/pins_RAMPS.h @@ -436,7 +436,9 @@ #endif #define BTN_ENC 35 - #define SD_DETECT_PIN 49 + #ifndef SD_DETECT_PIN + #define SD_DETECT_PIN 49 + #endif #define KILL_PIN 41 #if ENABLED(BQ_LCD_SMART_CONTROLLER) @@ -526,7 +528,6 @@ // From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 #define BEEPER_PIN 37 - #define LCD_RESET_PIN 23 #define DOGLCD_A0 16 #define DOGLCD_CS 17 @@ -537,14 +538,36 @@ #define SD_DETECT_PIN 49 - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN 25 + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN 27 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN 29 + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" #endif #elif ENABLED(MINIPANEL) diff --git a/Marlin/src/pins/pins_RAMPS_FD_V1.h b/Marlin/src/pins/pins_RAMPS_FD_V1.h index a8bec209ef..78e75d9116 100644 --- a/Marlin/src/pins/pins_RAMPS_FD_V1.h +++ b/Marlin/src/pins/pins_RAMPS_FD_V1.h @@ -150,32 +150,71 @@ #if ENABLED(NEWPANEL) #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 #endif #if ENABLED(FYSETC_MINI_12864) #define DOGLCD_CS LCD_PINS_ENABLE #define DOGLCD_A0 LCD_PINS_RS - #elif ENABLED(MINIPANEL) - #define DOGLCD_CS 25 - #define DOGLCD_A0 27 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + + #elif ENABLED(NEWPANEL) + + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + #if ENABLED(MINIPANEL) + #define DOGLCD_CS 25 + #define DOGLCD_A0 27 + #endif + #endif #if ANY(VIKI2, miniVIKI) - #define DOGLCD_A0 16 - #define KILL_PIN 51 - #define STAT_LED_BLUE_PIN 29 - #define STAT_LED_RED_PIN 23 - #define DOGLCD_CS 17 - #define DOGLCD_SCK 76 // SCK_PIN - These are required for DUE Hardware SPI - #define DOGLCD_MOSI 75 // MOSI_PIN - #define DOGLCD_MISO 74 // MISO_PIN + #define DOGLCD_A0 16 + #define KILL_PIN 51 + #define STAT_LED_BLUE_PIN 29 + #define STAT_LED_RED_PIN 23 + #define DOGLCD_CS 17 + #define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI + #define DOGLCD_MOSI 75 // MOSI_PIN + #define DOGLCD_MISO 74 // MISO_PIN #endif - #endif // ULTRA_LCD #if HAS_DRIVER(TMC2208) @@ -201,10 +240,8 @@ // // M3/M4/M5 - Spindle/Laser Control // -#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA) - #if HOTENDS < 3 - #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA - #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM - #define SPINDLE_DIR_PIN 47 // Use E2 DIR - #endif +#if HOTENDS < 3 && ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA) + #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA + #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN 47 // Use E2 DIR #endif diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/pins_RAMPS_RE_ARM.h index 9c7bbf4eea..5871b80d15 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/pins_RAMPS_RE_ARM.h @@ -320,6 +320,7 @@ #define DOGLCD_MOSI P0_18 #define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals #define DOGLCD_A0 P1_14 + #define FORCE_SOFT_SPI // required on a Re-ARM system #else #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 diff --git a/Marlin/src/pins/pins_RURAMPS4D_11.h b/Marlin/src/pins/pins_RURAMPS4D_11.h index 517be5b9b5..718e44651e 100644 --- a/Marlin/src/pins/pins_RURAMPS4D_11.h +++ b/Marlin/src/pins/pins_RURAMPS4D_11.h @@ -202,31 +202,24 @@ // #if ENABLED(ULTRA_LCD) - #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) - + #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BEEPER_PIN 62 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN 51 + #endif + + #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) #define LCD_PINS_RS 63 #define LCD_PINS_ENABLE 64 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) - #define BEEPER_PIN 62 - #define LCD_PINS_RS 52 #define LCD_PINS_ENABLE 53 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif HAS_SSD1306_OLED_I2C @@ -234,16 +227,57 @@ #define LCD_SDSS 10 #define SD_DETECT_PIN 51 + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 62 + #define DOGLCD_CS 64 + #define DOGLCD_A0 63 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + #elif ENABLED(SPARK_FULL_GRAPHICS) //http://doku.radds.org/dokumentation/other-electronics/sparklcd/ #error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D." - //#define LCD_PINS_D4 29//? - //#define LCD_PINS_ENABLE 27//? - //#define LCD_PINS_RS 25//? - //#define BTN_EN1 35//? - //#define BTN_EN2 33//? - //#define BTN_ENC 37//? + //#define LCD_PINS_D4 29 //? + //#define LCD_PINS_ENABLE 27 //? + //#define LCD_PINS_RS 25 //? + //#define BTN_EN1 35 //? + //#define BTN_EN2 33 //? + //#define BTN_ENC 37 //? #endif // SPARK_FULL_GRAPHICS diff --git a/Marlin/src/pins/pins_RURAMPS4D_13.h b/Marlin/src/pins/pins_RURAMPS4D_13.h index ab4aea0f2b..ddae87c245 100644 --- a/Marlin/src/pins/pins_RURAMPS4D_13.h +++ b/Marlin/src/pins/pins_RURAMPS4D_13.h @@ -188,31 +188,24 @@ // #if ENABLED(ULTRA_LCD) - #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) - + #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BEEPER_PIN 62 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN 51 + #endif + + #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) #define LCD_PINS_RS 63 #define LCD_PINS_ENABLE 64 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) - #define BEEPER_PIN 62 - #define LCD_PINS_RS 52 #define LCD_PINS_ENABLE 53 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif HAS_SSD1306_OLED_I2C @@ -220,6 +213,47 @@ #define LCD_SDSS 10 #define SD_DETECT_PIN 51 + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 62 + #define DOGLCD_CS 64 + #define DOGLCD_A0 63 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + #elif ENABLED(MKS_MINI_12864) #define ORIG_BEEPER_PIN 62 diff --git a/README.md b/README.md index 115d3d10c2..414efa5e89 100644 --- a/README.md +++ b/README.md @@ -1,7 +1,9 @@ # Marlin 3D Printer Firmware -[![Build Status](https://travis-ci.org/MarlinFirmware/Marlin.svg?branch=RCBugFix)](https://travis-ci.org/MarlinFirmware/Marlin) -[![Coverity Scan Build Status](https://scan.coverity.com/projects/2224/badge.svg)](https://scan.coverity.com/projects/2224) +[![Build Status](https://travis-ci.org/MarlinFirmware/Marlin.svg?branch=bugfix-2.0.x)](https://travis-ci.org/MarlinFirmware/Marlin) +![GitHub](https://img.shields.io/github/license/marlinfirmware/marlin.svg) +![GitHub contributors](https://img.shields.io/github/contributors/marlinfirmware/marlin.svg) +![GitHub Release Date](https://img.shields.io/github/release-date/marlinfirmware/marlin.svg) @@ -65,7 +67,7 @@ The current Marlin dev team consists of: - Roxanne Neufeld [[@Roxy-3D](https://github.com/Roxy-3D)] - USA - Bob Kuhn [[@Bob-the-Kuhn](https://github.com/Bob-the-Kuhn)] - USA - Chris Pepper [[@p3p](https://github.com/p3p)] - UK - - João Brazio [[@jbrazio](https://github.com/jbrazio)] - Brazil + - João Brazio [[@jbrazio](https://github.com/jbrazio)] - Portugal - Erik van der Zalm [[@ErikZalm](https://github.com/ErikZalm)] - Netherlands   [![Flattr Erik](http://api.flattr.com/button/flattr-badge-large.png)](https://flattr.com/submit/auto?user_id=ErikZalm&url=https://github.com/MarlinFirmware/Marlin&title=Marlin&language=&tags=github&category=software) ## License diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 7ea040803c..6b24012db1 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index 7b459d3c33..a236c65cfa 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -2044,6 +2044,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 60c94e8e02..23a18ca030 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -2033,6 +2033,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 1be8dde594..86a9d1bf6a 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index f9de2247b8..19920c0161 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -2024,6 +2024,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index db89142199..fed0e75f09 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -2015,6 +2015,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 68190a9ef9..23f1cf5f36 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -2015,6 +2015,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index e0b5c1a282..b33abd387f 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -2167,6 +2167,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index fee9dad53d..430e175824 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -2028,6 +2028,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index af01e1cf45..540956d7fa 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -2023,6 +2023,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 31a10f05c2..7d23ad27ee 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -2014,6 +2014,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 1d22e52b70..959ec9c669 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 7cbe3edd9d..b8c873de36 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 5ff9eb893b..847a0dbc43 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 91d315373e..a98e73d97a 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -2001,6 +2001,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 64c950f285..474110f36f 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index ef5a1ddb84..3b1eafc686 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -2001,6 +2001,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 09b003c572..06586f2e0d 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -2012,6 +2012,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index 0e0c476888..93f1daf401 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -2023,6 +2023,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index bbb5c4114b..a2c0418d01 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -2014,6 +2014,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index a8222e3b33..bb8872c622 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -2016,6 +2016,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h index 1c6b3d0b8b..2639fc587b 100644 --- a/config/examples/Creality/CR-10mini/Configuration.h +++ b/config/examples/Creality/CR-10mini/Configuration.h @@ -2032,6 +2032,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index eb2c0bf4d0..9fb629a362 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -2023,6 +2023,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index bd22dd9007..1d093d064c 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h index 377e344e82..195440f59e 100644 --- a/config/examples/Creality/Ender-3/Configuration.h +++ b/config/examples/Creality/Ender-3/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 608e6dccfd..e6d585d7a2 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -2023,6 +2023,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 45f0ef3f41..246bd987b7 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -2019,6 +2019,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h index f02a9e2203..1183a2e898 100644 --- a/config/examples/Felix/Configuration.h +++ b/config/examples/Felix/Configuration.h @@ -1995,6 +1995,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 530c1e9797..ec3992e801 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -1995,6 +1995,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 8978fb3baa..410c3052b4 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -2004,6 +2004,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index f2b962411a..5f8a8717ad 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -2019,6 +2019,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 116014d3c1..dcff640026 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -2118,6 +2118,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 82d24eb43f..3432036702 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -2048,6 +2048,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can @@ -2159,3 +2160,9 @@ // Allow servo angle to be edited and saved to EEPROM //#define EDITABLE_SERVO_ANGLES + +#ifdef ROXYs_TRex + #define LED_PIN -1 + #define BEEPER_PIN -1 + #define KILL_PIN -1 +#endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index 992d2c0e17..9c133527a8 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -2041,6 +2041,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can @@ -2152,3 +2153,9 @@ // Allow servo angle to be edited and saved to EEPROM //#define EDITABLE_SERVO_ANGLES + +#ifdef ROXYs_TRex + #define LED_PIN -1 + #define BEEPER_PIN -1 + #define KILL_PIN -1 +#endif diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 0aa45ee20a..462f7f9dee 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -1998,6 +1998,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 6c7b93cff8..1f3b8b66b1 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -2002,6 +2002,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index bd7800bb7e..197e85680a 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -2028,6 +2028,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 6605797f21..930e6dedcb 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -2002,6 +2002,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index d969f9803d..2ad7cb0931 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -2020,6 +2020,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 604ec61f2b..babbbf0afc 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -2029,6 +2029,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 03917da9a7..e65c48122f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -2028,6 +2028,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 666ce89889..7f2ae01d6d 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 6edcc7494e..49b71294ab 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index f859c70128..7cc745496f 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 4e2e0c7f30..5497ce8616 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -2025,6 +2025,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index e06c956457..4048345289 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -2033,6 +2033,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index e382233f69..0efe5b988e 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -2041,6 +2041,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index c9051fb748..270dd7c6a5 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -2012,6 +2012,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 24e930d20b..90e2b17c45 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 2b0413b90b..c399906143 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 97af15a496..ecfc05ead3 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -2015,6 +2015,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index 0bdf95a2c4..8883141cc6 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index e944085fc9..b0dfb4c4c9 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -2021,6 +2021,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index d3c2f4cc94..ff20725785 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 749afb889a..d58be3ee4a 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -2062,6 +2062,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 79fceac73a..82a30f4549 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 3fbd34e9c3..2add4143c6 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h index 86a0b9e88a..14c30d0362 100644 --- a/config/examples/SCARA/Configuration.h +++ b/config/examples/SCARA/Configuration.h @@ -2026,6 +2026,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index f34dee19d3..978acbf91d 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h index 76cbc4575b..abe8d54c4b 100644 --- a/config/examples/STM32/STM32F10/Configuration.h +++ b/config/examples/STM32/STM32F10/Configuration.h @@ -2015,6 +2015,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 3c4a93c816..49b92aefd1 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h index 6ee6cbbcef..ba17e68c14 100644 --- a/config/examples/STM32/stm32f103ret6/Configuration.h +++ b/config/examples/STM32/stm32f103ret6/Configuration.h @@ -2015,6 +2015,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 8b8e85259d..8fcfb0b6b4 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -2044,6 +2044,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 9fb8ed0298..dd6e1d845a 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 7f1935c531..cd89ad5a93 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -2069,6 +2069,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 02af26a50f..b13a74ed42 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 549b9a3ccd..9a58226861 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -2017,6 +2017,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index 0658378a25..a91d1a0f96 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -2034,6 +2034,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 736f158d93..381b760d9f 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -2012,6 +2012,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 0634641812..612942ead1 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -2024,6 +2024,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 06cd59ad41..e95be76d2d 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index fd4fe1e07c..772f7e963a 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index f043405d23..27be2081d8 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -2022,6 +2022,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index fb749e8433..2cf1d85c6b 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -2048,6 +2048,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h index 24aeab6486..262dbfce16 100644 --- a/config/examples/Velleman/K8400/Configuration.h +++ b/config/examples/Velleman/K8400/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 2438b75856..7cf031922a 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 5b234bf0a3..c6d9db2f57 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -2032,6 +2032,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 78d8d6bf1a..a52db9f8ad 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -2026,6 +2026,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index 4ceeb498ba..f7d21c2013 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -2013,6 +2013,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index f59af6179e..7a97646ae5 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -2200,6 +2200,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index f83290a9eb..d1ba36e9a8 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -2141,6 +2141,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index d95d6da056..3b01bfed59 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -2140,6 +2140,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 22154ab350..8be2d2e29e 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -2140,6 +2140,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 42d183a8e4..090409f534 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -2128,6 +2128,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index fd9fc95c84..6f2292bb80 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -2143,6 +2143,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 94ddadc040..99696d4526 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -2128,6 +2128,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index c27c9fd11b..6eb82bc85b 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -2121,6 +2121,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 685b30bc5a..36cea0c6f2 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -2128,6 +2128,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index bd668c0745..94131fd952 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -2130,6 +2130,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index 44cc6a30a3..5a12ddc97f 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -2131,6 +2131,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 1b18389b42..5a92c6a13a 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -2131,6 +2131,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 9c372a0ea0..95d5844778 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -2016,6 +2016,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 495190c9cf..791b3afcb9 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -2016,6 +2016,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index d46552e33c..82eef350cf 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -2008,6 +2008,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h index 5c22c426c5..1e009ff19a 100644 --- a/config/examples/wt150/Configuration.h +++ b/config/examples/wt150/Configuration.h @@ -2018,6 +2018,7 @@ // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] #define SOFT_PWM_SCALE 0 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can