GTM32 Pro pins updates (#14505)

This commit is contained in:
Alexander Amelkin 2019-07-06 05:09:17 +03:00 committed by Scott Lahteine
parent 10a71e332d
commit 7a42132002

View File

@ -34,21 +34,36 @@
#define BOARD_NAME "GTM32 Pro VB" #define BOARD_NAME "GTM32 Pro VB"
//#define DISABLE_DEBUG //#define DISABLE_DEBUG
//
// It is required to disable JTAG function because its pins are
// used as GPIO to drive the Y axis stepper.
// DO NOT ENABLE!
//
#define DISABLE_JTAG #define DISABLE_JTAG
//
// If you don't need the SWDIO functionality (any more), you may
// disable SWD here to regain PA13/PA14 pins for other use.
//
//#define DISABLE_JTAGSWD //#define DISABLE_JTAGSWD
// Ignore temp readings during development. // Ignore temp readings during development.
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // EEPROM end address (4kB)
// //
// Limit Switches // Limit Switches
// //
#define X_MIN_PIN PE5 #define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 #define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 #define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 #define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 #define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 #define Z_MAX_PIN PE0 // ENDSTOPS 4,6
// //
// Steppers // Steppers
@ -65,46 +80,52 @@
#define Z_DIR_PIN PD3 #define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3 #define Z_ENABLE_PIN PB3
#define E0_STEP_PIN PB2 // Extruder stepper pins
#define E0_DIR_PIN PB11 // NOTE: Numbering here is made according to EXT connector numbers,
#define E0_ENABLE_PIN PC4 // the FANx_PWM line numbering in the schematics is reverse.
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0 #define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6 #define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1 #define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PC14 #define E2_STEP_PIN PB2
#define E2_DIR_PIN PC13 #define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC15 #define E2_ENABLE_PIN PC4
// //
// Heaters / Fans // Heaters / Fans
// //
#define HEATER_0_PIN PB0 #define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 #define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 #define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 #define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define FAN_PIN PB7 // TODO: Add functionality //
#define FAN1_PIN PB8 // TODO: Add functionality // These are FAN PWM pins on EXT0..EXT2 connectors.
#define FAN2_PIN PB9 // TODO: Add functionality //
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
// //
// Temperature Sensors // Temperature Sensors
// //
#define TEMP_0_PIN PC2 // PORT NUMBERING #define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // PORT NUMBERING #define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // PORT NUMBERING #define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // PORT NUMBERING #define TEMP_BED_PIN PC3 // CON2X3 hotbed port
// //
// Misc. Functions // Misc. Functions
// //
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector #define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//#define RESET_PIN NRST
#define T_PEN PE6
#define BEEPER_PIN PB10
// //
// LCD / Controller // LCD / Controller
@ -112,6 +133,11 @@
#if HAS_SPI_LCD #if HAS_SPI_LCD
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
//
// LCD display on J2 FFC40
// Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select #define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI) #define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock #define LCD_PINS_D4 PD8 // SCK (CLK) clock
@ -119,12 +145,12 @@
#define LCD_PINS_D6 PD10 #define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15 #define LCD_PINS_D7 PE15
#define BTN_EN1 PE8 #else
#define BTN_EN2 PE9 //
#define BTN_ENC PE13 // Serial LCDs can be implemented in ExtUI
//
#define SD_DETECT_PIN PC7 //#define LCD_UART_TX PD8
#define KILL_PIN -1 //#define LCD_UART_RX PD9
#endif #endif
#ifndef ST7920_DELAY_1 #ifndef ST7920_DELAY_1
@ -137,59 +163,72 @@
#define ST7920_DELAY_3 DELAY_NS(715) #define ST7920_DELAY_3 DELAY_NS(715)
#endif #endif
//
// UART LCD Pins, if used
//
//#define LCD_PINS_D14 PD9 // RXD3
//#define LCD_PINS_D13 PD8 // TXD3
#endif // HAS_SPI_LCD #endif // HAS_SPI_LCD
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
// //
// SPI2 on LCD conn // Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
// //
#define SPI2_MOSI PB15 #define BTN_EN1 PE8
#define SPI2_MISO PB14 #define BTN_EN2 PE9
#define SPI2_SCK PB13 #define BTN_ENC PE13
#define SPI2_NSS PB12
#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
#endif
// //
// SD Card on LCD // Beeper
// //
#define SD_CD PC7 #ifdef GTM32_PRO_VB_USE_LCD_BEEPER
#define SD_DATA0 PC8 // This is pin 32 on J2 FFC40 and pin, goes to the beeper
#define SD_DATA1 PC9 // on Geeetech's version of RepRapDiscount Smart Controller
#define SD_DATA2 PC10 // (e.g. on Rostock 301)
#define SD_DATA3 PC11 #define BEEPER_PIN PE12
#define SD_CMD PD2 #else
#define SD_CLK PC12 // This is the beeper on the board itself
#define BEEPER_PIN PB10
#endif
/**
* The on-board TF_CARD_SOCKET microSD card socket has no SD Detect pin wired.
*
* The FFC10 (SD_CARD) connector has the same pins as those routed to the FFC40 (J2)
* connector, which usually go to the SD Card slot on the Geeetech version of the
* RepRapDiscount Smart Controller. Both connectors have the card detect signal.
*
* The on-board SD card and the external card (on either SD_CARD or J2) are two
* separate devices and can work simultaneously. Unfortunately, Marlin only supports
* a single SPI Flash device (as of 2019-07-05) so only one is enabled here.
*/
#if ENABLED(GTM32_PRO_VB_USE_EXT_SDCARD)
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
// //
// SPI Flash (on board Card Socket) // ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
// //
#define SPI1_NSS PA4 #define ESP_WIFI_MODULE_COM 2
#define SPI1_SCK PA5 #define ESP_WIFI_MODULE_BAUDRATE 115200
#define SPI1_MISO PA6 #define ESP_WIFI_MODULE_RESET_PIN -1
#define SPI1_MOSI PA7
//
// Debug
//
//#define SDA PA13
//#define SCL PA14
//
// Wifi
//
#define USART2_RX PA3 // Default alternate function
#define USART2_TX PA2 // Default alternate function
//
// For future use
//
//#undef USB_DM
//#undef CAN_TX
//#undef USB_DP
//#undef CAN_RX
//#undef BOARD_JTDI_PIN
//#define BOOT0 BOOT0