Update copyright in header, etc. (#14645)

This commit is contained in:
Ludy 2019-07-17 05:42:36 +02:00 committed by Scott Lahteine
parent 5535a047d7
commit abc9b52692
6 changed files with 77 additions and 64 deletions

View File

@ -260,7 +260,7 @@
#define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on Fysetc schematic)
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN P2_12
#define NEOPIXEL_PIN P2_12
#endif
#elif ENABLED(MINIPANEL)
@ -304,9 +304,14 @@
#endif
#if MB(MKS_SBASE) && HAS_TMC220x
// The shortage of pins becomes apparent.
// Worst case you may have to give up the LCD
// RX pins need to be interrupt capable
/**
* TMC2208/TMC2209 stepper drivers
*
* The shortage of pins becomes apparent.
* Worst case you may have to give up the LCD
* RX pins need to be interrupt capable
*/
#define X_SERIAL_TX_PIN P1_22 // J8-2
#define X_SERIAL_RX_PIN P2_12 // J8-4 Interrupt Capable
#define Y_SERIAL_TX_PIN P1_23 // J8-3
@ -344,26 +349,26 @@
* PWM1.6 P2_05 RAMPS_D10_PIN
*/
/**
* Special pins
* P1_30 - not 5V tolerant - EXP1
* P1_31 - not 5V tolerant - EXP1
* P0_27 - open collector - EXP2
* P0_28 - open collector - EXP2
*
*/
/**
* Special pins
* P1_30 - not 5V tolerant - EXP1
* P1_31 - not 5V tolerant - EXP1
* P0_27 - open collector - EXP2
* P0_28 - open collector - EXP2
*
*/
/**
* Serial Ports
* P0_00 - Port 3
* P0_01 - SD Card (Onboard)
* P0_10 - Port 2
* P0_11 - Y_EN/Y_DIR
* P0_15 - Port 1
* P0_16 - EXP1
* P0_02 - Port 0
* P0_03 - AUX1
* P0_29 - Port -1
* P0_30 - USB
*
*/
/**
* Serial Ports
* P0_00 - Port 3
* P0_01 - SD Card (Onboard)
* P0_10 - Port 2
* P0_11 - Y_EN/Y_DIR
* P0_15 - Port 1
* P0_16 - EXP1
* P0_02 - Port 0
* P0_03 - AUX1
* P0_29 - Port -1
* P0_30 - USB
*
*/

View File

@ -110,7 +110,7 @@
#if HAS_TMC220x
/**
* TMC2208 stepper drivers
* TMC2208/TMC2209 stepper drivers
*
* Hardware serial communication ports.
* If undefined software serial is used according to the pins below

View File

@ -121,24 +121,24 @@
* If undefined software serial is used according to the pins below
*/
/**
* Software serial
*/
//
// Software serial
//
// P2_08 E1-Step
// P2_13 E1-Dir
// P2_08 E1-Step
// P2_13 E1-Dir
#define X_SERIAL_TX_PIN P2_13
#define X_SERIAL_RX_PIN P2_13
#define X_SERIAL_TX_PIN P2_13
#define X_SERIAL_RX_PIN P2_13
#define Y_SERIAL_TX_PIN P0_00
#define Y_SERIAL_RX_PIN P0_00
#define Y_SERIAL_TX_PIN P0_00
#define Y_SERIAL_RX_PIN P0_00
#define Z_SERIAL_TX_PIN P0_01
#define Z_SERIAL_RX_PIN P0_01
#define Z_SERIAL_TX_PIN P0_01
#define Z_SERIAL_RX_PIN P0_01
#define E0_SERIAL_TX_PIN P2_08
#define E0_SERIAL_RX_PIN P2_08
#define E0_SERIAL_TX_PIN P2_08
#define E0_SERIAL_RX_PIN P2_08
#endif
@ -254,9 +254,9 @@
#error "LASER_FEATURE requires 3 free servo pins."
#endif
#endif
#define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN SERVO2_PIN // (5)
#define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN SERVO2_PIN // (5)
#endif
//
@ -309,10 +309,10 @@
#elif HAS_SPI_LCD
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
#if ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN P1_01
@ -337,10 +337,10 @@
#define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#endif
#else
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
#endif
#if ANY(VIKI2, miniVIKI)
@ -365,7 +365,7 @@
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
// results in LCD soft SPI mode 3, SD soft SPI mode 0
#define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally.
#define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
@ -378,7 +378,7 @@
#define RGB_LED_B_PIN P1_08
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN P1_00
#define NEOPIXEL_PIN P1_00
#endif
#else
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2

View File

@ -40,13 +40,17 @@
//#undef BTN_EN1
//#undef BTN_EN2
//#define BTN_EN1 P1_23 // EXP2.5
//#define BTN_EN2 P1_22 // EXP2.3
//#define BTN_EN1 P1_23 // EXP2.5
//#define BTN_EN2 P1_22 // EXP2.3
#if HAS_TMC220x
// The shortage of pins becomes apparent.
// In the worst case you may have to give up the LCD.
// RX pins must be interrupt-capable.
/**
* TMC2208/TMC2209 stepper drivers
*
* The shortage of pins becomes apparent.
* In the worst case you may have to give up the LCD.
* RX pins must be interrupt-capable.
*/
#define X_SERIAL_TX_PIN P4_29 // J8-2
#define X_SERIAL_RX_PIN P4_29 // J8-2

View File

@ -118,8 +118,12 @@
//
#if HAS_TMC220x
// Software serial
// At the moment, F6 rx pins are not pc interrupt pins
/**
* TMC2208/TMC2209 stepper drivers
*
* Software serial communication pins.
* At the moment, F6 rx pins are not pc interrupt pins
*/
#define X_SERIAL_RX_PIN -1 // 71
#define X_SERIAL_TX_PIN 72
#define Y_SERIAL_RX_PIN -1 // 73

View File

@ -1,9 +1,9 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@ -99,9 +99,9 @@
#define E4_ENABLE_PIN 47
#define E4_CS_PIN E0_CS_PIN
#if ENABLED(HAVE_TMC2208)
#if HAS_TMC220x
/**
* TMC2208 stepper drivers
* TMC2208/TMC2209 stepper drivers
*
* Hardware serial communication ports.
* If undefined software serial is used according to the pins below