🔧 Group FAST_PWM_FAN.options (#23331)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

Marlin/Configuration.h

@@ -2841,9 +2841,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

Marlin/Configuration_adv.h

@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
+ * to produce a frequency as close as possible to the desired frequency.
- * frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
  *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+//#define FAST_PWM_FAN    // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  //#define FAST_PWM_FAN_FREQUENCY 31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

Marlin/src/inc/Conditionals_post.h

@@ -2667,17 +2667,6 @@
   #error "FAN_OFF_PWM must be less than or equal to FAN_MIN_PWM."
 #endif
 
-/**
- * FAST PWM FAN default PWM frequency
- */
-#if !defined(FAST_PWM_FAN_FREQUENCY) && ENABLED(FAST_PWM_FAN)
-  #ifdef __AVR__
-    #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
-  #else
-    #define FAST_PWM_FAN_FREQUENCY 1000U
-  #endif
-#endif
-
 /**
  * Controller Fan Settings
  */

Marlin/src/pins/stm32f1/pins_LONGER3D_LK.h

@@ -95,7 +95,6 @@
   #define FAN_MAX_PWM                        255
 #else
   #define FAST_PWM_FAN                            // STM32 Variant allow TIMER2 Hardware PWM
-  #define FAST_PWM_FAN_FREQUENCY           31400  // This frequency allow a good range, fan starts at 3%, half noise at 50%
   #define FAN_MIN_PWM                          5
   #define FAN_MAX_PWM                        255
 #endif