diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 84cf41631d..13f855fc35 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -978,8 +978,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1104,7 +1106,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index 47fea5818a..84794bd98a 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -977,8 +977,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// #define CARTESIO_UI // @@ -1103,7 +1105,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 26493f74a3..cab1522c09 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -391,50 +391,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -486,6 +442,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -656,7 +656,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -962,8 +961,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1088,7 +1089,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 706d2a3987..322b36f19e 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -389,50 +389,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -484,6 +440,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -654,7 +654,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -960,8 +959,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1086,7 +1087,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 18f2734287..59a111d4fd 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -666,7 +666,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -971,8 +970,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1097,7 +1098,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 62b75ff82f..eb209befb1 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -512,8 +512,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // For M851 give a range for adjusting the Z probe offset // -#define Z_PROBE_OFFSET_RANGE_MIN -20 -#define Z_PROBE_OFFSET_RANGE_MAX 20 +#define Z_PROBE_OFFSET_RANGE_MIN -5 +#define Z_PROBE_OFFSET_RANGE_MAX 0 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} @@ -733,11 +733,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Additional Features =========================== //============================================================================= -// @section probes - -#define Z_PROBE_OFFSET_RANGE_MIN -5 -#define Z_PROBE_OFFSET_RANGE_MAX 0 - // @section extras // @@ -977,8 +972,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1103,7 +1100,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 40755a0af3..16ae40da10 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -426,50 +426,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -521,6 +477,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -691,7 +691,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -996,8 +995,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1122,7 +1123,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 64a79f7eb4..a2492565c2 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -674,7 +674,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -979,8 +978,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1105,7 +1106,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 443f9d8ae7..5cbf98f9fa 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -668,7 +668,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -974,8 +973,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1102,7 +1103,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 89b397a80d..1da70ab1b4 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -417,50 +417,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -512,6 +468,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -682,7 +682,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -987,8 +986,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1113,7 +1114,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 5412a499eb..fc7805553e 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -430,50 +430,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -525,6 +481,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -695,7 +695,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1000,8 +999,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1126,7 +1127,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 97195830fd..7712caab3b 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -666,7 +666,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -971,8 +970,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1097,7 +1098,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index be76093053..8225450f7b 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -674,7 +674,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -979,8 +978,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1105,7 +1106,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 496ccc4aa7..1f57ead7e5 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -583,6 +539,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -1063,8 +1063,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1189,7 +1191,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 7cd5a52440..acfe15c187 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -577,6 +533,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -1057,8 +1057,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1183,7 +1185,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index dce2a460c3..34fcddc73c 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -580,6 +536,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -1060,8 +1060,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1186,7 +1188,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 13214454f6..10bc948871 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -440,50 +440,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -574,6 +530,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -588,8 +588,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // For M851 give a range for adjusting the Z probe offset // -#define Z_PROBE_OFFSET_RANGE_MIN -20 -#define Z_PROBE_OFFSET_RANGE_MAX 20 +#define Z_PROBE_OFFSET_RANGE_MIN -15 +#define Z_PROBE_OFFSET_RANGE_MAX 5 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} @@ -821,11 +821,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Additional Features =========================== //============================================================================= -// @section probes - -#define Z_PROBE_OFFSET_RANGE_MIN -15 -#define Z_PROBE_OFFSET_RANGE_MAX 5 - // @section extras // @@ -1065,8 +1060,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1191,7 +1188,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index f9b12b1942..1c295bd519 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -449,50 +449,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -575,6 +531,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -1062,8 +1062,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1188,7 +1190,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 6f30d11885..76bc85ccab 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -412,50 +412,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -507,6 +463,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -677,7 +677,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -982,8 +981,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1108,7 +1109,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306 diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 643372bc7a..e79d722cc5 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -399,50 +399,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -494,6 +450,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -664,7 +664,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -973,8 +972,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define ULTIPANEL +// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// //#define CARTESIO_UI // @@ -1099,7 +1100,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define U8GLIB_SSD1306 +// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// //#define SAV_3DGLCD #if ENABLED(SAV_3DGLCD) //#define U8GLIB_SSD1306