📌 Define RAMPS_SMART EXP headers, AZSMZ_12864

See #23501
This commit is contained in:
Scott Lahteine 2022-05-09 17:35:32 -05:00
parent a9aca5f5e8
commit bd09f8acff
3 changed files with 51 additions and 25 deletions

View File

@ -101,9 +101,8 @@
#elif ANY(miniVIKI, VIKI2, WYH_L12864, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864) #elif ANY(miniVIKI, VIKI2, WYH_L12864, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864)
#define IS_DOGM_12864 1
#define DOGLCD #define DOGLCD
#define IS_DOGM_12864 1
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#if ENABLED(miniVIKI) #if ENABLED(miniVIKI)

View File

@ -600,6 +600,10 @@
#define LCD_PINS_D6 AUX2_08_PIN #define LCD_PINS_D6 AUX2_08_PIN
#define LCD_PINS_D7 AUX2_10_PIN #define LCD_PINS_D7 AUX2_10_PIN
#elif ENABLED(AZSMZ_12864)
// Pins only defined for RAMPS_SMART currently
#else #else
#if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306)

View File

@ -61,53 +61,43 @@
*/ */
#define BOARD_INFO_NAME "RAMPS-SMART" #define BOARD_INFO_NAME "RAMPS-SMART"
#define ALLOW_SAM3X8E
#include "../ramps/pins_RAMPS.h"
// I2C EEPROM with 4K of space // I2C EEPROM with 4K of space
#define I2C_EEPROM #define I2C_EEPROM
#define MARLIN_EEPROM_SIZE 0x1000 #define MARLIN_EEPROM_SIZE 0x1000 // 4K
#define SDA_PIN 20
#define SCL_PIN 21
// See EEPROM device datasheet for the following values. These are for 24xx256 // See EEPROM device datasheet for the following values. These are for 24xx256
#define EEPROM_SERIAL_ADDR 0x50 // 7 bit i2c address (without R/W bit) #define EEPROM_DEVICE_ADDRESS 0x50 // 7 bit i2c address (without R/W bit)
#define EEPROM_PAGE_SIZE 64 // page write buffer size #define EEPROM_WRITE_DELAY 7 // page write time in milliseconds (docs say 5ms but that is too short)
#define EEPROM_PAGE_WRITE_TIME 7 // page write time in milliseconds (docs say 5ms but that is too short) //#define EEPROM_PAGE_SIZE 64 // page write buffer size
//#define TWI_CLOCK_FREQ 400000
#define TWI_CLOCK_FREQ 400000 //#define EEPROM_ADDRSZ_BYTES TWI_MMR_IADRSZ_2_BYTE // TWI_MMR_IADRSZ_1_BYTE for 1 byte, or TWI_MMR_IADRSZ_2_BYTE for 2 byte
#define EEPROM_ADDRSZ_BYTES TWI_MMR_IADRSZ_2_BYTE // TWI_MMR_IADRSZ_1_BYTE for 1 byte, or TWI_MMR_IADRSZ_2_BYTE for 2 byte //#define EEPROM_AVAILABLE EEPROM_I2C
#define EEPROM_AVAILABLE EEPROM_I2C
#define RESET_PIN 42 // Resets the board if the jumper is attached
// //
// Temperature Sensors // Temperature Sensors
// //
#undef TEMP_0_PIN
#define TEMP_0_PIN 9 // Analog Input #define TEMP_0_PIN 9 // Analog Input
#undef TEMP_1_PIN
#define TEMP_1_PIN 10 // Analog Input #define TEMP_1_PIN 10 // Analog Input
#undef TEMP_BED_PIN
#define TEMP_BED_PIN 11 // Analog Input #define TEMP_BED_PIN 11 // Analog Input
// SPI for MAX Thermocouple // SPI for MAX Thermocouple
#undef TEMP_0_CS_PIN
#if DISABLED(SDSUPPORT) #if DISABLED(SDSUPPORT)
#define TEMP_0_CS_PIN 67 // Don't use 53 if using Display/SD card #define TEMP_0_CS_PIN 67 // Don't use 53 if using Display/SD card
#else #else
#define TEMP_0_CS_PIN 67 // Don't use 49 (SD_DETECT_PIN) #define TEMP_0_CS_PIN 67 // Don't use 49 (SD_DETECT_PIN)
#endif #endif
#define SDA_PIN 20
#define SCL_PIN 21
#define RESET_PIN 42 // Resets the board if the jumper is attached
// //
// LCD / Controller // LCD / Controller
// //
// Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel
#if ENABLED(AZSMZ_12864) #if ENABLED(AZSMZ_12864)
// Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel
#define BEEPER_PIN 66 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65 #define BEEPER_PIN 66 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65
#define DOGLCD_A0 59 #define DOGLCD_A0 59
#define DOGLCD_CS 44 #define DOGLCD_CS 44
@ -116,4 +106,37 @@
#define BTN_ENC 67 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66 #define BTN_ENC 67 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66
#define SD_DETECT_PIN 49 // Pin 49 for display sd interface, 72 for easy adapter board #define SD_DETECT_PIN 49 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 42 #define KILL_PIN 42
#else
/** ------ ------
* 37 |10 9 | 35 (MISO) 50 |10 9 | 52 (SCK)
* 31 | 8 7 | 41 29 | 8 7 | 53
* 33 6 5 | 23 25 6 5 | 51 (MOSI)
* 42 | 4 3 | 44 49 | 4 3 | 27
* GND | 2 1 | 5V GND | 2 1 | --
* ------ ------
* EXP1 EXP2
*/
#define EXP1_03_PIN 44
#define EXP1_04_PIN 42
#define EXP1_05_PIN 23
#define EXP1_06_PIN 33
#define EXP1_07_PIN 41
#define EXP1_08_PIN 31
#define EXP1_09_PIN 35
#define EXP1_10_PIN 37
#define EXP2_03_PIN 27
#define EXP2_04_PIN 49
#define EXP2_05_PIN 51
#define EXP2_06_PIN 25
#define EXP2_07_PIN 53
#define EXP2_08_PIN 29
#define EXP2_09_PIN 52
#define EXP2_10_PIN 50
#endif #endif
#define ALLOW_SAM3X8E
#include "../ramps/pins_RAMPS.h"