diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 400b2f6e0b..df2eaa279c 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h index cca4784368..8deec82756 100644 --- a/Marlin/example_configurations/Cartesio/Configuration_adv.h +++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index ce5fee9f94..075705faf8 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 63214e64f9..7a6fb6ff46 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index 131d6efb46..4a7c897e19 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index c4a2f20b9e..79e2be3d8f 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -321,13 +321,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h index 1626f2ffe9..06a3d76da3 100644 --- a/Marlin/example_configurations/K8400/Configuration_adv.h +++ b/Marlin/example_configurations/K8400/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 589758e337..354ec7d6de 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index 3033bcdd6d..03a80fb4e5 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index 0ae81cfbbf..b2e339f144 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -316,13 +316,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 63214e64f9..7a6fb6ff46 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index bd8bd22970..e85e3ed5d5 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 14213dac4f..986189c545 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 14213dac4f..986189c545 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index 33e591078f..4c51232ca1 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -313,13 +313,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index 0fc896f6ba..86fe5f1533 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index e8d3bec2d1..4709333a71 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index b0b9e917ff..f1c0f80cd9 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE